Spaceman 6228AH Bedienungsanleitung
SPACEMAN AIR
PUMP SOFT
SERVE TRAINING
*use this training guide for Spaceman USA models:
6228AH, 6235AH, 6236AH, 6250AH, 6260AH, 6338AH, and 6378AH
Spaceman USA Soft Serve Pump Training
rev042219
NOTES AND FUNCTIONS OF YOUR MACHINE
Product is poured into the refrigerated hopper (product should be
below 41°F) where it is kept until flowing into the freezing cylinder via
the air tube.
On the front of your machine is an digital control to regulate and
maintain consistent product quality for each flavor as an analog rocker
switch to power the board on or off.
Inside the freezing cylinder, the beater mixes the product while freezing
and produces a soft serve product.
The machine you have purchased is an air pump soft serve machine.
It is capable of producing a variety of products that include: Soft Serve
Frozen Yogurt, Ice Cream, select custard products, and sorbets.
•Air pump (or pressurized) soft serve machines use pressure to add a higher, controlled
percentage of air to the product mix and maintain pressure in the freezing cylinder so that the
air does not escape. Air pump machines are ideal for customers looking for higher profits,
creamier product, or anyone serving cones.
Spaceman USA Soft Serve Pump Training
rev042219
ROUTINE MAINTENANCE OPERATIONS
Clean and Lubricate Daily
Replace Wearable Parts Every
1 to 3 months*
Internal Cleaning Quarterly**
* Based on machine usage and cleaning
intervals; a Tune-Up Kit is available with
all wearable parts (O-rings, gaskets, etc.)
except scraper blades
** Based on cleanliness of location
and proximity to powder-based
machines
For optimal machine performance and
many years of efficiency and reliability
from your machine, Spaceman USA
recommends cleaning and sanitizing the
machine and its parts daily. The machine
comes equipped with a brush kit
specifically designed to efficiently and
properly clean the machine.
Tune-Up Kit
Spaceman USA Soft Serve Pump Training
rev042219
IMPORTANT:
Cleaning and sanitizing
schedules are governed by state
or local regulatory agencies and
MUST be followed accordingly.
Routine maintenance MUST be
performed a minimum of once
every three days.
CAUTIONS:
Do NOT run the machine without properly lubricating
required parts.
Do NOT clean the machine with abrasive or toxic chemicals
and cleaners. Doing so may cause damage to the stainless
steel material.
ONLY use Spaceman-USA-included cleaning brushes and lubrication.
NEVER use metal objects to clean or operate the machine.
ALWAYS replace wearable parts a minimum of every 3 months.
ALWAYS prime machine prior to operating.
ALWAYS inspect parts for excess wear and damage.
ROUTINE MAINTENANCE OPERATIONS
Spaceman USA Soft Serve Pump Training
rev042219
DRAIN PRODUCT
NOTE CAUTION
To expedite draining, turn off
machine 30 minutes prior to
soften product. To expedite
process, keep a bucket
nearby to temporarily store
removed parts.
NEVER use warm water
when rinsing the machine
to prevent damage.
Spaceman USA Soft Serve Pump Training
rev042219
Press RESET buttons;
press WASH buttons
DRAIN PRODUCT
Remove hopper lids and
agitators
2
Place a bucket or other
container below
dispensing assembly
3
Turn power
switches to ON
41
Spaceman USA Soft Serve Pump Training
rev042219
DRAIN PRODUCT
Fill each hopper with
one gallon of COOL
water
Move draw handles to OPEN
position (DOWN); CLOSE
draw handles (UP) when
product flow slows
significantly
Press RESET buttons to
pause wash cycle
Remove product
and dispose or
refrigerate it
5 6 7 8
Spaceman USA Soft Serve Pump Training
rev042219
DRAIN PRODUCT
OPEN draw handles to
drain water and
remaining product;
CLOSE when finished
Use cool water and the large
brush to scrub the sides and
bottom of the hoppers; be VERY
careful not to damage the low-
mix sensor in the hoppers
Place a bucket or other
container below the
dispensing assembly
Press WASH buttons
10 11 12
Spaceman USA Soft Serve Pump Training
rev042219
9
DRAIN PRODUCT
Use the small brush kit to
clean inside the feed tube at
the bottom of the hoppers
Press RESET to
pause wash cycle
Repeat steps 9 to 15
until water exiting the
draw valves is clear
and free of product
If machine has air pumps:
a. Press RESET buttons
b. OPEN draw handles
(DOWN) for 10 to 15
seconds to relieve
pressure in cylinders
13 14 15 16a
16b
Spaceman USA Soft Serve Pump Training
rev042219
DISASSEMBLE
NOTE CAUTION
Prepare dishwashing area
prior to disassembly, use
bucket to temporarily store
large removed parts and a
small container for O-rings,
and have a towel nearby to
capture excess water.
ALWAYS separate O-rings
and gaskets from metal
parts to prevent damage
while washing.
Spaceman USA Soft Serve Pump Training
rev042219
Dieses Handbuch passt für folgende Modelle
6
Inhaltsverzeichnis
Andere Spaceman Eismaschine Handbücher
Spaceman
Spaceman Gravity Fed Machine Bedienungsanleitung
Spaceman
Spaceman 6224 Bedienungsanleitung
Spaceman
Spaceman 6210 Bedienungsanleitung
Spaceman
Spaceman SM-6455H Bedienungsanleitung
Spaceman
Spaceman SM-6236H Bedienungsanleitung
Spaceman
Spaceman 6220 Series Bedienungsanleitung
Spaceman
Spaceman SM-6450 Bedienungsanleitung
Spaceman
Spaceman SM-6220 Bedienungsanleitung
Spaceman
Spaceman SM-6228H Bedienungsanleitung
Spaceman
Spaceman SM-6210 Bedienungsanleitung
