Spaceman Gravity Fed Machine Bedienungsanleitung
Soft Serve Ice-Cream Machines
How To Clean, Lubricate and Reassemble Your
Gravity Fed Machine
CREATED by CELCO INC 1
Please follow these start-up instructions every time you clean your machine
For Spaceman Ice Cream Machines already in use, please follow the
“How To Clean and Lubricate Your Gravity Fed Machine”
instructions shown in a separate powerpoint.
CREATED by CELCO INC 2
Twice A Week - Minimum
You must have 6” of clearance on all sides of the machine
The unit requires this spacing to prevent hot air from recirculating into the
machine and causing poor freezer operation.
CREATED by CELCO INC 3
Please Note –Spaceman Lubricant and Stera Sheen Sanitizer (Milkstone
Remover) are both approved for lubricating and sanitizing your Spaceman
machine. If you wish to use another product, please call Celco or Spaceman
for approval as not all products are compatible with Spaceman machines.
Thank You
CREATED by CELCO INC 4
For cleaning and sanitizing your machine you will require:
A Container or Bucket To Hold All Parts
A Food Grade Bucket for Mixing
A Whisk
Disposable Gloves
Brush Kit
Lubricant (1 tube comes with the machine)
Ice Cream Machine Sanitizer
CREATED by CELCO INC 5
Drain Product From The Machine
If the unit was in overnight/standby mode removal of the product is easier as the cylinder
product is not frozen, only chilled.
Remove the lid from
the hopper and take
out the air tube. Set
the air tube into the
container for cleaning
If the unit has
product in it, press
RESET
then wash. If the
machine was just in
use and the cylinder
product is frozen let
the wash cycle run
for a minute or two.
With a bucket under the dispensing
assembly, pull down the draw handles
to dispense the product. If the product
is to be kept, draw one handle at a
time, pouring product into separate
containers, and then place the product
into a fridge. Once product slows
down press RESET.
CREATED by CELCO INC 6
Cleaning The Hopper On The Gravity Fed Unit
Pour clean cold
water into the
hopper to rinse
out the product.
Allow the water to
drain into the
cylinder and then
add more water
to half fill the
hopper
Using the brush
kit, swish the
water around to
remove the
product residue
from the sides
and bottom.
Wash brush in
clean water.
Use a smaller
brush to clean the
tube leading from
the hopper to the
cylinder Press RESET then
WASH and wait for
2 minutes
CREATED by CELCO INC 7
With the wash
mode still on, place
a clean bucket
under the
discharge assembly
door and draw off
the water from the
hoppers
Once the water
slows down to a
trickle, press
RESET to stop
the wash cycle
Add another
bucket of cold
clean water to the
hopper to clean it
this time
Use the brushes
to clean the inside
of the hopper
CREATED by CELCO INC 8
Press RESET and
then WASH and
let it run for 5
minutes
With the wash
mode still on, place
a clean bucket
under the
discharge assembly
door and draw off
the water from the
hoppers
You are now
washing the
machine
Once the water
slows down to a
trickle, press
RESET to stop
the wash cycle.
You can now
turn the
machine off.
CREATED by CELCO INC 9
Remove the
hopper agitator
from the hopper
Move the
hopper agitators
to the container
for washing
Wipe out and dry the
hoppers
CREATED by CELCO INC 10
1, 3, or 5 draw handles –1, 2, or 3 hoppers.
All units are cleaned and sanitized the same way. Machines with multiple
handles and hoppers will have more parts to clean.
In this powerpoint we are cleaning a 3 draw handle unit.
You Are Now Ready To Take The Door Assembly Apart
Andere Spaceman Eismaschine Handbücher
Spaceman
Spaceman SM-6236H Bedienungsanleitung
Spaceman
Spaceman SM-6450 Bedienungsanleitung
Spaceman
Spaceman SM-6228H Bedienungsanleitung
Spaceman
Spaceman SM-6220 Bedienungsanleitung
Spaceman
Spaceman 6228AH Bedienungsanleitung
Spaceman
Spaceman 6210 Bedienungsanleitung
Spaceman
Spaceman SM-6695H Bedienungsanleitung
Spaceman
Spaceman SM-6210 Bedienungsanleitung
Spaceman
Spaceman 6210-60Hz Bedienungsanleitung
Spaceman
Spaceman SM-6455H Bedienungsanleitung
