Spectra Logic Spectra 2000 Bedienungsanleitung

P.N. 90870070 Revision B

Spectra 2000™Mammoth-2 Drive

Sled Assembly Guide

2 Spectra 2000 Mammoth-2 Drive Sled Assembly Guide

Notices

Spectra Logic Corporation provides this publication “as is” without warranty of any kind, either

expressed or implied, including but not limited to the implied warranties of merchantability or

fitness for a particular purpose. In no event shall Spectra Logic be liable for any loss of profits,

loss of business, loss of use or data, interruption of business, or for indirect, special, incidental,

or consequential damages of any kind, even if Spectra Logic has been advised of the possibility of

such damages arising from any defect or error in this publication or in Virtual Control Panel

software.

Information furnished in this manual is believed to be accurate and reliable. However, no responsibility is assumed by Spectra

Logic for its use. Due to continuing research and development, Spectra Logic may revise this publication from time to time without

notice, and reserves the right to change any product specification at any time without notice.

Some products or services mentioned in this manual are provided by companies other than Spectra Logic . Inquires about one or

more of these products or services should be sent directly to the company in question. This manual refers to the following brand

or product names, registered trademarks, and trademarks that are listed according to their respective owners. These trademarks

may be registered in this country, other countries, or both.

Spectra 2000 Mammoth-2 Drive Sled Assembly Guide

Spectra Logic Corporation

TreeFrog™

Spectra 2000™

Exabyte

Mammoth-2™

Spectra 2000 Mammoth-2 Drive Sled Assembly Guide 3

Contents

Introduction ...........................................................................................................4

Assemble the Drive Sled........................................................................................5

Finish......................................................................................................................8

4 Spectra 2000 Mammoth-2 Drive Sled Assembly Guide

Introduction

About this manual

This guide explains how to assemble a Mammoth-2 drive sled for use with a Spectra 2000

automated tape library.

Caution: The Mammoth-2 tape drive is a static sensitive device. Use a static

dissipative wrist strap or other ESD equipment/tools for this process.

How long will this take?

This procedure should take less than 15 minutes.

What you will need

You will need a Mammoth-2 Drive Sled Assembly Kit, P.N. 90870556. The Mammoth-2 Drive

Sled Assembly Kit contains:

You will also need:



A #1 Phillips screwdriver



A Mammoth-2 drive

Part Number Description

4250 Screws (4)

90870157 Spectra 2000 5.25” Drive Sled

90870316 SCSI ID cable

90870070 Spectra 2000 Mammoth-2 Drive Sled Assembly Guide (this guide)

Spectra 2000 Mammoth-2 Drive Sled Assembly Guide 5

Assemble the Drive Sled

1. Assemble all parts on your work surface (Figure 1).

2. Align the Mammoth-2 drive in the drive sled so the drive door is facing the drive

sled’s front lip and the SCSI ID Settings label is visible at the top of the assembly

(Figure 2).

3. The drive sled has two screw holes at the top of each side. Position the drive so its

screw holes are aligned with the drive sled’s screw holes.

Figure 1 Drive sled assembly parts.

Figure 2 Align the Mammoth-2 in the Drive Sled.

6 Spectra 2000 Mammoth-2 Drive Sled Assembly Guide

Assemble the Drive Sled

4. Use the #1 Phillips screwdriver to attach the Mammoth-2 tape drive to the drive sled

(Figure 3).

Note: Make sure to use only the two screw holes at the top of each side of the

drive sled. There should only be two screws on each side.

Figure 3 Attach the Mammoth-2 to the drive sled.

Spectra 2000 Mammoth-2 Drive Sled Assembly Guide 7

Assemble the Drive Sled

5. Turn the drive sled assembly over and plug the SCSI ID cable into the rear of the

Mammoth-2 drive . The keyed connector will only plug into the drive with the tab

facing up (Figure 4).

Figure 4 Plugthe SCSI ID cable into the drive.

8 Spectra 2000 Mammoth-2 Drive Sled Assembly Guide

Finish

There is a chance your Mammoth-2 drive sled may have been bent in shipping. Before installing

the Mammoth-2 drive sled in your Spectra 2000 automated tape library, check to ensure the

drive sled lip is flush with the drive face plate (Figure 5, Figure 6).

If the Mammoth-2 drive sled is bent:

1. Remove the drive from drive sled.

Caution: You must remove the Mammoth-2 drive from the drive sled before

correcting the bent drive sled lip. Failure to do so can result in damage

to the drive.

Figure 5 Drive sled lip flush with drive faceplate. Figure 6 Drive sled lip bent up from drive faceplate.

Spectra 2000 Mammoth-2 Drive Sled Assembly Guide 9

Finish

2. Using your hands, bend the drive sled so the lip is flush with the drive faceplate.

Use light pressure (Figure 7).

3. Attach the Mammoth-2 tape drive to the drive sled.

Note: If the Mammoth-2 drive screw holes will not align with the drive sled’s

screw holes, you have bent the drive sled lip too far. Remove the drive

from the drive sled and try again.

If you have difficulty

If you need further assistance with this procedure, call Spectra Logic Technical Support at (800)

227-4637 or (303) 449-6444, extension 3175.

Figure 7 Bend drive sled.

Andere Handbücher für Spectra 2000

Inhaltsverzeichnis

Andere Spectra Logic Lagerung Handbücher

Spectra Logic

Spectra Logic Spectra 12000 Bedienungsanleitung

Spectra Logic

Spectra Logic Spectra 64K Bedienungsanleitung

Spectra Logic

Spectra Logic Spectra S50 Bedienungsanleitung

Spectra Logic

Spectra Logic Spectra nTier300 Bedienungsanleitung

Spectra Logic

Spectra Logic Spectra 12K Handbuch

Spectra Logic

Spectra Logic Spectra T950V Bedienungsanleitung

Spectra Logic

Spectra Logic Spectra 10000 Bedienungsanleitung

Spectra Logic

Spectra Logic Spectra RXT150 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T200 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T120 Leitfaden

Spectra Logic

Spectra Logic T-Series Spectra T950 Bedienungsanleitung

Spectra Logic

Spectra Logic Spectra nTier700 Bedienungsanleitung

Spectra Logic

Spectra Logic Spectra nTier300 Bedienungsanleitung

Spectra Logic

Spectra Logic Spectra 2000 Handbuch

Spectra Logic

Spectra Logic Spectra 12000 Handbuch

Spectra Logic

Spectra Logic BlackPearl NAS Bedienungsanleitung

Spectra Logic

Spectra Logic Spectra RXT Media Bedienungsanleitung

Spectra Logic

Spectra Logic Spectra 20K Bedienungsanleitung

Spectra Logic

Spectra Logic BlackPearl Bedienungsanleitung

Spectra Logic

Spectra Logic Spectra 2k AIT Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50 Bedienungsanleitung

Spectra Logic

Spectra Logic Spectra nTier500 Bedienungsanleitung

Spectra Logic

Spectra Logic Spectra nTier300 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T24 Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung

Dell

Dell PowerVault MD3600f Series Bedienungsanleitung