Spirit 350 Bedienungsanleitung

PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE

OPERATING YOUR NEW ELLIPTICAL!

Z100 / Z300 Z500 Z700

OWNER’S MANUAL

XE 150

Elliptical

XE 350

Elliptical

XE 550

Elliptical

XE Series Elliptical

Product Registration…………………………………………………………………………. 2

Important Safety Instructions…………………………………………………………………3

Important Electrical Information………………………………………………………………4

Important Operation Instructions……………………………………………………………..4

Assembly Instructions………………………………………………………………………….5

Features……………………………………………………………………………………….. 13

Operation of Your New Elliptical……………………………………………………………...22

Manufacturer’s Limited Warranty……………………………………………………………..33

Table of Contents

ATTENTION-

THIS ELLIPTICAL IS INTENDED FOR RESIDENTIAL USE ONLY

AND IS WARRANTED FOR THAT APPLICATION. ANY OTHER APPLICATION

VOIDS THIS WARRANTY IN ITS ENTIRETY.

XE Series Elliptical

Thank you for your purchase of this quality elliptical trainer from Spirit

Manufacturing, Inc. Your new elliptical was manufactured by one of the leading

fitness manufacturers in the world and is backed by one of the most

comprehensive warranties available. Through your dealer, Spirit will do all we can

to make your ownership experience as pleasant as possible for many years to

come. The local dealership where you purchased this elliptical is your

administrator for all Spirit warranty and service needs. Their responsibility is to

provide you with the technical knowledge and service personnel to make your

experience more informed and any difficulties easier to remedy.

Please take a moment at this time to record the name of the dealer, their

telephone number, and the date of purchase below to make any future, needed

contact easy. We appreciate your support and we will always remember that you

are the reason that we are in business. Please complete and mail your

registration card today and enjoy your new elliptical.

Yours in Health,

Spirit Manufacturing, Inc.

Name of Dealer______________________________________

Telephone Number of Dealer___________________________

Purchase Date_______________________________________

RECORD YOUR SERIAL NUMBER

Please record the Serial Number of this fitness product in the space provided below.

Serial Number_______________________________________

The self-addressed product registration card must be completed in full and returned to

Spirit Manufacturing, Inc or visit www.spiritfitness.com to register online.

CONGRATULATIONS ON YOUR

NEW ELLIPTICAL AND WELCOME

TO THE SPIRIT FAMILY!

Product Registration

XE Series Elliptical

WARNING - Read all instructions before using this appliance.

■Do not operate

elliptical

on deeply padded, plush or shag carpet. Damage to both

carpet and

elliptical

may result.

■Keep children away from the

elliptical

. There are obvious pinch points and other

caution areas that can cause harm.

■ Keep hands away from all moving parts.

■ Never operate the elliptical if it has a damaged cord or plug. If the elliptical is not

working properly, call your dealer.

■ Keep the cord away from heated surfaces.

■Do not operate where aerosol spray products are being used or where oxygen is

being administered. Sparks from the motor may ignite a highly gaseous

environment.

■ Never drop or insert any object into any openings.

■ Do not use outdoors.

■To disconnect, turn all controls to the off position, then remove the plug from the

outlet.

■Do not attempt to use your

elliptical

for any purpose other than for the purpose it is

intended.

■The hand pulse sensors are not medical devices. Various factors, including the

user’s movement, may affect the accuracy of heart rate readings. The pulse sensors are

intended only as exercise aids in determining heart rate trends in general.

■Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable

for use on your

elliptical

. Quality athletic shoes are recommended to avoid leg

fatigue.

SAVE THESE INSTRUCTIONS - THINK SAFETY!

Important Safety Instructions

XE Series Elliptical

WARNING!

●

NEVER remove any cover without first disconnecting AC power supply.

●

If A.C. voltage varies by ten percent (10%) or more, the performance of your elliptical

may be affected. Such conditions are not covered under your warranty. If you

suspect the voltage is low, contact your local power company or a licensed electrician

for proper testing.

●

NEVER expose this

elliptical

to rain or moisture. This product is NOT designed for

Use outdoors, near a pool or spa, or in any other high humidity environment.

●

NEVER operate this elliptical without reading and completely understanding the

results of any operational change you request from the computer.

●

Understand that changes in resistance do not occur immediately. Set your desired

level on the computer console and release the adjustment key. The computer will

obey the command gradually.

●

NEVER use your elliptical during an electrical storm. Surges may occur in your

household power supply that could damage elliptical components.

●

Use caution while participating in other activities while using your elliptical such as

watching television, reading, etc. These distractions may cause you to lose balance

which may result in serious injury.

●

Always hold on to a handrail or hand bar while making control changes.

Do not use excessive pressure on console control keys. They are precision set to

properly function with little finger pressure. Pushing harder is not going to make the unit

go faster or slower. If you feel the buttons are not functioning properly with normal

pressure, contact your Spirit dealer.

Important Electrical Information

Important Operation Instructions

XE Series Elliptical

■

■■

■UNPACKING THE UNIT

1. Carefully remove all parts from carton and inspect for any damage or missing parts. If

damaged parts are found, or parts are missing, contact your dealer immediately.

2. Locate the hardware package. The hardware is separated into steps. Remove the tools

first. Remove the hardware for each step as needed to avoid confusion.

STEP 1: REAR RAIL ASSEMBLY

1. Remove the hardware from the hardware pack for step 1. You should have four

3-3/4” X 3/8” bolts, four curved washers, two 1/4” X 3/8” bolts, two flat washers

and six 3/4” X 1/8” Phillips head screws.

2. Put the two flat washers on the 2-1/4” bolts and hand-tighten them, through the

top of the middle stabilizer tube, into the rear rail assembly.

3. Put the four curved washers on the 3-3/4” bolts and hand-tighten them through

the front of the middle stabilizer tube, into the rear rail assembly.

4. Using the wrench provided tighten all six bolts securely.

5. Locate the four plastic covers (XE150, XE350 only) for the rear rail assembly

and the one cover for the front stabilizer and install them using the six 3/4” X

1/4“ screws and the Phillips head screw driver provided.

STEP 2: CONSOLE MAST ASSEMBLY

1. Remove the hardware from the hardware pack for step 2. You should have one

2-3/4” X 3/8” bolt, one lock washer, two 1” X 3/8” bolts, two curved washers and

four 1/2” X 1/4” Phillips head screws.

2. Locate the console mast and console mast cover and slide the cover onto the

mast as far as it will go. Make sure the cover is facing the correct way.

3. At the top opening of the main body of the elliptical is a wire harness. Unravel

and straighten out the wire harness and feed it into the bottom of the console

mast tube and out of the top opening.

4. Install the console mast into the receiving bracket in the top of the main body.

Assembly Instructions

XE Series Elliptical

NOTE: there is one bolt already installed in the receiving bracket that will engage

with the slot at the bottom of the console mast. This needs to be tightened at the

end along with the three other console mast bolts.

5. Put the flat washer onto the 2 3/4” bolt and the two curved washers onto the two

1” bolts. Install, and hand tighten, the 2 3/4” bolt through the left side of the

receiving tube into the console mast. NOTE: There is a wire running through the

tube. Be careful not to damage or pinch this wire during this procedure. Damage

to the electronic console could result. Install, and hand tighten, the two 1” bolts

through the front of the receiving tube into the console mast.

6. Using the two sided wrench tighten the three bolts, and the fourth bolt which is

pre-installed, firmly. These bolts should be tightened as much as you possibly

can.

7. Locate the electronic console and the four 1/2” X 1/4” Phillips head screws.

8. There will be two electrical wire connectors at the top opening of the console

mast, one 4 pin (hand pulse sensors), one 10 pin (main wire harness). Connect

these to the mating connectors on the back of the console. The connectors are

keyed so you cannot plug them in the wrong way so do not force them.

9. Storing the excess wire back into the console mast, carefully install the console

onto the mounting plate and secure using the four Phillips head screws.

STEP 3: HANDLE BAR ASSEMBLY

1. Remove the hardware from the hardware pack for step 3. You should have two

5/8” X 3/8” bolts, two large flat washers, two large wave washers and four self

tapping Phillips head screws.

2. Locate and install the 2 large wave washers onto the handle bar axle, one on

each side.

3. Slide the left and right handle bars onto the appropriate side of the axle. There is

a sticker on each handle bar indicating Lfor left and Rfor right.

4. Put the large flat washers onto the two 5/8” X 3/8” bolts and install, and tighten,

in the threaded holes in the ends of the axle.

5. Install the plastic covers over the handle bar/axle connections with the six self

tapping Phillips head screws.

STEP 4: FOOT PAD/CONNECTING ARM ASSEMBLY

1. Remove the hardware from the hardware pack for step 4. You should have two

1-1/4” X 3/8” bolts, two flat washers, two Nyloc® nuts, four 5/8” machine screws

(long), four 3/8” machine screws (short) and two self tapping Phillips head

XE Series Elliptical

screws.

2. On the pedal arms, in the middle on top, there are two axles already installed in

the bushing housings. Remove, from one side of each axle, the bolt (one should

be loose) and washer. Remove the axle and set aside for the next step.

3. Locate the left foot pad/connecting arm. Holding the rear of the foot pad with

your right hand and the connecting arm, just in front of the foot pad, with your left

hand, place the foot pad over the bushing housing.

4. Holding the axle (removed in step 2) in one hand, and the foot pad in the other,

line up the large hole in the side of the bracket (under the foot pad) with the hole

in the bushing housing and insert the axle all the way until the washer is flush

against the bracket. You may have to wiggle the axle while moving the foot pad

slightly to get the axle to go in.

5. Take the bolt and washer that you removed from the axle in step 2 and thread it

into the hole in the axle. Tighten the bolt using two wrenches provided. You have

to put a wrench on both axle bolts to tighten firmly.

6. Align the hole in the end of the connecting arm (pivoting rod end) with the hole in

the bracket of the handle bar. The rod end should be on the inside of the handle

bar bracket. Take one of the 1-1/4” X 3/8” bolts and install it through the handle

bar bracket and the rod end. Install a flat washer and Nyloc® nut on the bolt and

tighten firmly using a wrench on the nut and one on the bolt.

7. Repeat for the right side foot pad/connecting arm.

8. Install the plastic covers over the connection of the rod end and handle bar. The

front inside hole in the plastic uses a self tapping screw and the two rear holes

use the 3/8” machine screws (short). There is a short Phillips screw driver

provided for installing the inside screws.

9. Install the two wheel covers using the four 5/8” machine screws (long).

10.Install the locking pins for the adjustable foot pads into the desired holes (XE350,

XE550 only). *See Foot pad angle adjustment section for details of this feature.

11.This step is for the XE550 only. Install the two plastic parts that make up the rear

shroud using the seven Phillips head screws.

XE Series Elliptical

XE150

Assembly drawing (XE150.XE350.XE550)

XE Series Elliptical

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Spirit Ellipsentrainer Handbücher

Spirit

Spirit XE500 Bedienungsanleitung

Spirit

Spirit XE295 Bedienungsanleitung

Spirit

Spirit XE320 Bedienungsanleitung

Spirit

Spirit XE295 Bedienungsanleitung

Spirit

Spirit XG200 Bedienungsanleitung

Spirit

Spirit CE900 Bedienungsanleitung

Spirit

Spirit XE395 Elliptical Bedienungsanleitung

Spirit

Spirit Group Exercise Elliptical Bedienungsanleitung

Spirit

Spirit CE800 Bedienungsanleitung

Spirit

Spirit CE900ENT Bedienungsanleitung

Spirit

Spirit CE800 Bedienungsanleitung

Spirit

Spirit Inspire ZE40 Bedienungsanleitung

Spirit

Spirit 16611608000 Bedienungsanleitung

Spirit

Spirit XG200e Bedienungsanleitung

Spirit

Spirit EL7 Bedienungsanleitung

Spirit

Spirit XE 125 Bedienungsanleitung

Spirit

Spirit Esprit EL255 Bedienungsanleitung

Spirit

Spirit SPT0034- XE195 Bedienungsanleitung

Spirit

Spirit CRS800 Bedienungsanleitung

Spirit

Spirit XE395 Elliptical Bedienungsanleitung

Spirit

Spirit XE895 Bedienungsanleitung

Spirit

Spirit ZE501 Bedienungsanleitung

Spirit

Spirit XE295 Bedienungsanleitung

Spirit

Spirit XE795 Bedienungsanleitung

Beliebte Ellipsentrainer Handbücher anderer Marken

Weslo

Weslo Momentum 4.0 Elliptical Bedienungs- und Wartungshandbuch

Progear Fitness

Progear Fitness Air elliptical pro 1307 Bedienungsanleitung

Torque Fitness

Torque Fitness XPLLP Bedienungsanleitung

Octane Fitness

Octane Fitness PRO3700C Bedienungsanleitung

Xterra

Xterra FS5.8e Bedienungsanleitung

Bodyguard

Bodyguard E-40 Bedienungsanleitung

Bonn Germany

Bonn Germany Concept 2.2 Bedienungsanleitung

Precor

Precor Resolute RSL 620 Bedienungsanleitung

NordicTrack

NordicTrack E 9.2 Elliptical Bedienungsanleitung

Vision Fitness

Vision Fitness X6600iNetTV Bedienungsanleitung

Matrix

Matrix MX-A5x Bedienungsanleitung

SportsArt Fitness

SportsArt Fitness ECO-NATURAL Elite E874 Bedienungsanleitung

Sears

Sears FREE SPIRIT C249 30737 0 Bedienungsanleitung

True

True FS-64 Bedienungsanleitung

Sport-thieme

Sport-thieme ST 310 Bedienungsanleitung

VIRTUFIT

VIRTUFIT CTR 1.1 Bedienungsanleitung

Kettler

Kettler GIRO C 1 Bedienungsanleitung

CIRCLE FITNESS

CIRCLE FITNESS E7 Bedienungsanleitung