ST SPC58XXADPT176S Bedienungsanleitung

Introduction

The SPC58XXADPT176S Rev.B evaluation board supports STMicroelectronics SPC58EE84E7, SPC58NE84E7,

SPC58XN8XE7 and SP58xG8xE7 microcontroller in LQFP 176 24x24x1.4 package with exposed pad down.

Figure 1. SPC58XXADPT176S Rev. B

SPC58XXADPT176S Rev.B evaluation board

UM2723

User manual

UM2723 - Rev 1 - June 2020

For further information contact your local STMicroelectronics sales office.

www.st.com

1Overview

The SPC58XXADPT176S Rev. B mini module is an evaluation board supporting STMicroelectronics

SPC58EE84L7, SPC58NE84E7, SPC58XN8XE7 and SP58xG8xE7 microcontrollers in LQFP 176 24x24x1.4

package with exposed pad down.

This mini module is designed to be connected onto the SPC58XXMB motherboard, offering a mechanism for easy

customer evaluation of the supported devices, and to facilitate hardware and software development.

The mini module may be used as a stand-alone unit allowing access to the CPU, but not to access to the I/O pins

nor any motherboard peripherals.

By default, the mini module is configured for SPC58EE84E7/SPC58NE84E7, easily supports SPC58XN8XE7 and

SPC58xG8xE7 simply changing the following through hole jumpers: J44, J45, J46 and J47.

1.1 Package contents

An SPC58XXADPT176S Rev. B adapter package includes the following item:

• SPC58XXADPT176S Rev. B mini module

1.2 Supported devices

The SPC58XXADPT176S Rev. B mini module supports the following STMicroelectronics family of

microcontrollers in LQFP 176 24x24x1.4 package with exposed pad down:

• SPC58EE84E7/SPC58NE84E7

• SPC58XN8XE7

• SPC58xG8E7

UM2723

Overview

UM2723 - Rev 1 page 2/28

2License agreement

The packaging of this evaluation board was sealed with a seal stating, “by breaking this seal, you agree to the

terms and conditions of the evaluation board license agreement, the terms and conditions of which are available

at http://www.st.com/ebla”. Upon breaking the seal, you and STMicroelectronics entered into the evaluation board

license agreement, a copy of which is also enclosed with the evaluation board for convenience.

Attention: This evaluation board only offers limited features for evaluating ST products. It has not been tested for use with

other products and is not suitable for any safety or other commercial or consumer application. This evaluation

board is otherwise provided “AS IS” and STMicroelectronics disclaims all warranties, express or implied,

including the implied warranties of merchantability and fitness for a particular purpose.

UM2723

License agreement

UM2723 - Rev 1 page 3/28

3Handling precautions

Please take care to handle the package contents in a manner such as to prevent electrostatic discharge.

Before the EVB is used or power is applied, please fully read the following sections on how to correctly configure

the board. Failure to correctly configure the board may cause irreparable component, MCU or EVB damage.

UM2723

Handling precautions

UM2723 - Rev 1 page 4/28

4Hardware description

4.1 Hardware features

The SPC58XXADPT176S Rev. B mini module board has the following features:

• Connector for external power supplies input (5 V, 3.3 V, 1.25 V) used in stand-alone mode

• Reset button with driver and led indicator

• Socket for device in LQFP 176 24x24x1.4 package with exposed pad down

• Debug interfaces:

– 14-pin header connector for JTAG interface

– 10-pin header connector for JTAG/LFAST LVDS interface

– 10-pin header connector for SIPI interface

• 40 MHz crystal main oscillator with jumpers to optionally disconnect it

• 8 MHz oscillator with jumpers to optionally disconnect it

• Clock input through SMA connector to optionally disconnect it

• Predisposed for SMPS regulator module

• 2 X Samtec QSH series, 240 way connector to connect mini module to Motherboard

UM2723

Hardware description

UM2723 - Rev 1 page 5/28

4.2 Hardware dimension

The mini module has the following dimensions:

• PCB area: 127 mm x 114.3 mm

• Top components height: 19 mm max

• Bottom components height: 3.5 mm max

• PCB thickness: 1.6 mm

Figure 2. SPC58XXADPT176S Rev. B top component view

UM2723

Hardware dimension

UM2723 - Rev 1 page 6/28

5Power and system configuration

5.1 Power supplies

The mini module can be powered by providing the three voltages (5 V, 3.3 V and 1.25 V) or supplied externally by

the 4 pins connector (J5) or supplied by the motherboard.

When the mini module is plugged onto the motherboard, power is supplied directly by the motherboard. In this

setup, the external power supply input available on the mini module should NOT be used.

When the SPC58XXADPT176S Rev. B mini module is used as a stand-alone board, external power supplies

must be used (5 V, 3.3 V, 1.25 V).

The following jumpers are used to configure the power supply (common for all supported devices):

Table 1. Power configuration jumpers

Jumper Description Default

VDD_HV_ADR voltage configuration:

• 1-2 5.0V_LR

• 2-3 3.3V_SR

1-2

(5.0V_LR)

VDD_HV_ADV voltage configuration:

• 1-2 5.0V_LR

• 2-3 3.3V_SR

1-2

(5.0V_LR)

VDD_HV_IO_JTAG voltage configuration:

• 1-2 5.0V_SR

• 2-3 3.3V_SR

1-2

(5.0V_SR)

VDD_HV_IO_MAIN voltage configuration:

• 1-2 5.0V_SR

• 2-3 3.3V_SR

1-2

(5.0V_SR)

VDD_HV_IO_FLEX voltage configuration:

• 1-2 5.0V_SR

• 2-3 3.3V_SR

1-2

(5.0V_SR)

J38

Device pin 153 EXTREG_SEL function configuration:

• 2-1 Reserved for STMicroelectronics

• 2-3 ENABLED BALLAST

• 2-4 DISABLE BALLAST

2-4

(DISABLE BALLAST)

J39

Supply for BALLAST circuit configuration

• 1-2 VDD_HV_IO_MAIN

• 2-3 5.0V_SR

1-2

(VDD_HV_IO_MAIN)

J40

VDD_LV voltage configuration:

• 2-1 (BALLAST circuit)

• 2-3 (1.25V_SR)

• 2-4 (SMPS regulator module) Do not use this configuration for

SP58xG8xE7

2-3

(1.25V_SR)

J43

Device pin 155 VDD_HV_FLA voltage configuration:

• OPEN – disconnect VDD_HV_FLA from VDD_HV_IO_MAIN

• CLOSED - connect VDD_HV_FLA from VDD_HV_IO_MAIN

Closed

(connect pin 155 VDD_HV_FLA

to VDD_HV_IO_MAIN)

UM2723

Power and system configuration

UM2723 - Rev 1 page 7/28

5.2 JTAG/LFAST LVDS interface configuration

The following jumpers need to configure the JTAG/LFAST LVDS:

Table 2. LFAST configuration jumpers

Jumper Description Default

J41

JTAG/LFAST LVDS pin 9 configuration

• 1-2: EVTO

• 2-3: ESR0

1-2

(EVTO)

J42

JTAG/LFAST LVDS pin 10 configuration

• 1-2: PORST

• 2-3: ESR0

1-2

(PORST)

5.3 System clock configuration

The mini module supports the usage of crystal clock sources as well as external clock source:

Table 3. Clock configuration jumpers

Jumper Description Default

J21

EXTAL configuration

• 1-2 pin 2 of 40 MHz crystal (Y1)

• 2-3 EVB-EXTAL

1-2

(XT1 pin2)

J23

XTAL configuration

• 1-2 pin 1 of 40 MHz crystal (Y1)

• 2-3 GND

1-2

(XT1 pin1)

J22

Enable 8 MHz oscillator power supply

• Open – power off

• Closed – power on

Open

(power off)

J24

External 8 MHz clock source

• 1-2 OSC-MOD (from oscillator)

• 2-3 EXTAL-SMA (from SMA connector)

1-2

(8 MHz from oscillator)

UM2723

JTAG/LFAST LVDS interface configuration

UM2723 - Rev 1 page 8/28

5.4 Reset circuit

The mini module supports different ways to reset the microcontroller. To use and perform the reset driving there

are different jumpers and switches:

Table 4. Reset configuration jumpers

Jumper Description Default

SW1 Reset push button Open

J27 Connect the external reset to the reset driver for ESR0 and PORST pins Close

J25 Connect the external reset to ESR0 pin Close

J26 Connect the external reset to PORST pin Close

5.5 Other jumpers

Table 5. Other jumpers

Jumper Description Default

VDD_HV_PMC voltage configuration:

• 1-2 5.0V_SR

• 2-3 3.3V_SR

1-2

(5.0V_SR)

J30 TESTMODE settings Close

(10 KΩ down)

5.6 Configuration for SPC58EE84E7/SPC58NE84E7 (default configuration)

To configure the board for SPC58EE84E7/SPC58NE84E7 set the jumpers described in the table below.

Table 6. SPC58EE84E7/SPC58NE84E7 configuration jumpers (default configuration)

Jumper Description Default

J44

Device pin 10 port configuration

• 1-2 PL8

• 2-3 VDD_LV_BD

1-2

(PL 8)

J45

Device pin 154 function configuration

• OPEN – disconnect BCTRL with ballast circuit

• CLOSED – connect BCTRL with ballast circuit

Closed

(connect BCTRL with BALLAST circuit)

J46

Device pin 79 configuration

• 1-2 PB10 (GPIO)

• 2-3 VDD_LV_BD (1.25V)

1-2 (PB10)

J47

Device pin 59 configuration

• 1-2 PE15 (GPIO)

• 2-3 VDD_HV_IO_MAIN

1-2 (PE15)

UM2723

Reset circuit

UM2723 - Rev 1 page 9/28

5.7 Configuration for SPC58EE84E7/SPC58NE84E7

To configure the board for SPC58EE84E7/SPC58NE84E7 set the jumpers described in the table below.

Table 7. SPC58EE84E7/SPC58NE84E7 configuration jumpers

Jumper Description Default

J44

Device pin 10 port configuration

1-2 PL8

2-3 VDD_LV_BD

1-2

(PL 8)

J45

Device pin 154 function configuration

• OPEN – disconnect BCTRL with ballast circuit

• CLOSED – connect BCTRL with ballast circuit

Closed

(connect BCTRL with BALLAST circuit)

J46

Device pin 79 configuration

• 1-2 PB10 (GPIO)

• 2-3 VDD_LV_BD (1.25V)

1-2 (PB10)

J47

Device pin 59 configuration

• 1-2 PE15 (GPIO)

• 2-3 VDD_HV_IO_MAIN

2-3 (VDD_HV_IO_BD)

5.8 Configuration for SPC58XN8XE7

To configure the board for SPC58XN8XE7 set the jumpers described in the table below.

Table 8. SPC58XN8XE7 configuration jumpers

Jumper Description Configuration

J44

Device pin 10 port configuration

1-2 PL8

2-3 VDD_LV_BD

1-2

(PL 8)

J45

Device pin 154 function configuration

• OPEN – disconnect BCTRL with ballast circuit

• CLOSED – connect BCTRL with ballast circuit

Open

(device pin 154 not connected)

J46

Device pin 79 configuration

• 1-2 PB10 (GPIO)

• 2-3 VDD_LV_BD (1.25V)

1-2 (PB10)

J47

Device pin 59 configuration

• 1-2 PE15 (GPIO)

• 2-3 VDD_HV_IO_MAIN

1-2 (PE15)

UM2723

Configuration for SPC58EE84E7/SPC58NE84E7

UM2723 - Rev 1 page 10/28

Inhaltsverzeichnis

Andere ST Hauptplatine Handbücher

ST STEVAL-PCC010V1 Bedienungsanleitung

ST STEVAL-IPP003V1 Kurzanleitung

ST ST72F651 Bedienungsanleitung

ST UM1935 Bedienungsanleitung

ST STEVAL-IPMM10B Bedienungsanleitung

ST STEVAL-IHM011V1 Bedienungsanleitung

ST ST25RU3993-EVAL Bedienungsanleitung

ST STEVAL-IHM022V1 Bedienungsanleitung

ST EVB-LIV4F Bedienungsanleitung

ST EVAL-RHRPMPOL01 Bedienungsanleitung

ST STEVAL-IHM031V1 Bedienungsanleitung

ST UM0969 Bedienungsanleitung

ST STEVAL-BTDP2 Bedienungsanleitung

ST X-NUCLEO-IDB04A1 Bedienungsanleitung

ST EVALKITSTKNX Bedienungsanleitung

ST eMotion STEVAL-MKI109V1 Bedienungsanleitung

ST STEVAL-SMARTAG2 Bedienungsanleitung

ST EVALSP1310CPU Bedienungsanleitung

ST STM32G4 Nucleo-32 Bedienungsanleitung

ST UM1461 Bedienungsanleitung

ST STEVAL-STRKT01 Administratorhandbuch

ST STM3240G-EVAL Bedienungsanleitung

ST SPC58NHADPT386S Bedienungsanleitung

ST STEVAL-PCC001V1 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung