ST UM0969 Bedienungsanleitung

November 2010 Doc ID 17665 Rev 1 1/57

UM0969

User manual

3-phase motor control demonstration board featuring IGBT

intelligent power module STGIPS10K60A

Introduction

This document describes the 1 kW 3-phase motor control demonstration board, featuring

the STGIPS10K60A: 600 V - 10 A IGBT Intelligent power module. The demonstration board

is a 3-phase inverter for driving an induction motor or PMSM motors up to 1000 W. The main

target of this application is to show users the performance of the ST 25L-SDIP (25-lead,

small dual inline package), IPM - STGIPS10K60A.

The board has been designed to be compatible with a single-phase supply from 90 VAC to

220 VAC, or for DC voltage from 125 VDC to 350 VDC. The document is associated with the

release of the STEVAL-IHM027V1 demonstration board (see Figure 1).

Figure 1. STEVAL-IHM027V1 demonstration board

www.st.com

Contents UM0969

2/57 Doc ID 17665 Rev 1

Contents

1 System introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.1 Main characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.2 Target application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.3 Safety and operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1.3.1 General terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1.3.2 Demonstration board intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1.3.3 Demonstration board installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1.3.4 Electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2 Board description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.1 System architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.2 Board schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.3 Circuit description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

2.3.1 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

2.3.2 Inrush limitation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

2.3.3 Brake function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

2.3.4 Overcurrent protection (OCP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

2.3.5 Current sensing amplifying network . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

2.3.6 Tachometer and Hall/encoder input . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

2.3.7 Temperature feedback and overtemperature protection (OTP) . . . . . . . 25

3 Hardware setting of the STEVAL-IHM027V1 . . . . . . . . . . . . . . . . . . . . . 27

3.1 Hardware settings with single-shunt configuration . . . . . . . . . . . . . . . . . . 27

3.2 Hardware settings with three-shunt configuration . . . . . . . . . . . . . . . . . . 28

3.3 Hardware settings for input stage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

4 Description of jumpers, test pins, and connectors . . . . . . . . . . . . . . . 30

5 Connector placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

6 BOM list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

7 PCB layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

UM0969 Contents

Doc ID 17665 Rev 1 3/57

8 Power losses and dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

8.1 Assumptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

8.2 Conduction loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

8.3 Switching loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

8.4 Thermal impedance overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

8.5 Temperature rise considerations and calculation example . . . . . . . . . . . . 48

9 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

10 Using the STEVAL-IHM027V1 with STM32 FOC firmware library . . . . 50

11 Environmental considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

12 Hardware requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

13 Software requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

14 Conclusion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

15 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

16 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

List of tables UM0969

4/57 Doc ID 17665 Rev 1

List of tables

Table 1. Jumper settings for a single-shunt or three-shunt configuration . . . . . . . . . . . . . . . . . . . . . 24

Table 2. Internal IPM NTC details (see relevant section on the STGIPS10K60A datasheet). . . . . . 26

Table 3. Jumper settings for single-shunt configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Table 4. Jumper settings for three-shunt configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Table 5. Input stage configuration details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Table 6. Jumpers description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Table 7. Connector pinout description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Table 8. Testing points description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Table 9. BOM list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Table 10. RC - Cauer STGIPS10K60A thermal network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Table 11. Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

UM0969 List of figures

Doc ID 17665 Rev 1 5/57

List of figures

Figure 1. STEVAL-IHM027V1 demonstration board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Figure 2. Motor control system architecture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Figure 3. Input stage with bridge schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Figure 4. Bus voltage sense resistor schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Figure 5. +5 V linear schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Figure 6. +3.3 V linear schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Figure 7. Buck converter schematic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Figure 8. Thermal shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Figure 9. NTC bypass schematic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Figure 10. Motor output schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Figure 11. +15 V auxiliary supply schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Figure 12. BEMF_daughter board schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Figure 13. Motor control connector schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Figure 14. Hall sensors\encoder schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Figure 15. Tachometer sensor schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Figure 16. Brake control schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Figure 17. STEVAL-IHM027V1 schematic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Figure 18. Current sensing A schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Figure 19. Current sensing B schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Figure 20. Current sensing C schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Figure 21. Overcurrent\overtemperature protection schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Figure 22. STEVAL-IHM027V1 power supply block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Figure 23. Three-shunt configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Figure 24. Single-shunt configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Figure 25. OT protection circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Figure 26. STEVAL-IHM027V1 input stage detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Figure 27. Connector placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Figure 28. Copper tracks - top side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Figure 29. Copper tracks - bottom side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Figure 30. Silk screen - top side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Figure 31. Silk screen - bottom side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Figure 32. Static parameter calculations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Figure 33. Equivalent STGIPS10K60A thermal network (CAUER models). . . . . . . . . . . . . . . . . . . . . 47

Figure 34. Maximum IC(RMS) current vs. switching frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

System introduction UM0969

6/57 Doc ID 17665 Rev 1

1 System introduction

1.1 Main characteristics

The main characteristics of the STEVAL-IHM027V1 demonstration board are:

●ST IGBT intelligent power module: STGIPS10K60A

●Minimum input voltage 125 VDC or 90 VAC

●Maximum input voltage 350 VDC or 220 VAC

●Possibility to use external +15 V supply voltage

●Maximum output power for motor up to 1000 W

●Regenerative brake control feature

●Input inrush limitation with bypassing relay

●+15 V auxiliary power supply based on buck converter with VIPer16

●Fully populated board conception with testing points

●Motor control connector for interface with STM3210B-EVAL board and further ST motor

control dedicated kits

●Tachometer input

●Hall\encoder inputs

●Possibility to connect BEMF daughter board for sensorless six-step control of BLDC

motors

●PCB type and size:

– Material of PCB: FR-4

– Double side layout

– Copper thickness: ~45 µm

– Dimension of demonstration board: 147 mm*157 mm

1.2 Target application

●Domestic appliances

●Medical applications, fitness applications

●High power industry pumps

●Medium power fans for HVAC

●Power tools

UM0969 System introduction

Doc ID 17665 Rev 1 7/57

1.3 Safety and operating instructions

1.3.1 General terms

Warning: During assembly, testing, and normal operation, the

demonstration board poses several inherent hazards,

including bare wires, moving or rotating parts and hot

surfaces. There is a danger of serious personal injury if the

kit or components are improperly used or incorrectly

installed. The kit is not electrically isolated from the AC/DC

input. The demonstration board is directly linked to the mains

voltage. No insulation is ensured between accessible parts

and high voltage. All measuring equipment must be isolated

from the mains before powering the board. When using an

oscilloscope with the demonstration board, it must be

isolated from the AC line. This prevents shock from occurring

as a result of touching any SINGLE point in the circuit, but

does NOT prevent shock when touching two or more points

in the circuit. Do not touch the demonstration board after

disconnection from the voltage supply; several parts and

power terminals, which contain energized capacitors, must

be allowed to discharge.

All operations involving transportation, installation and use, as well as maintenance, are to

be carried out by skilled technical personnel (national accident prevention rules must be

observed). For the purpose of these basic safety instructions, “skilled technical personnel”

are considered as suitably qualified people who are familiar with the installation, use, and

maintenance of power electronic systems.

1.3.2 Demonstration board intended use

The STEVAL-IHM027V1 demonstration board is designed for demonstration purposes only

and must not be used for any commercial purposes. The technical data, as well as

information concerning power supply conditions, must be taken from the relevant

documentation and strictly observed.

1.3.3 Demonstration board installation

The installation of the demonstration board must be in accordance with the specifications

and the targeted application.

●The boards contain electro-statically sensitive components that are prone to damage

through improper use. Electrical components must not be mechanically damaged or

destroyed

●Avoid any contacts with other electronic components

●During the motor drive converters must be protected against excessive strain. In

particular, no components are to be bent or isolating distances altered during the

course of transportation or handling

System introduction UM0969

8/57 Doc ID 17665 Rev 1

1.3.4 Electrical connections

Applicable national accident prevention rules must be followed when working on the main

power supply with a motor drive. The electrical installation must be completed in accordance

with the appropriate requirements. A system architecture which supplies power to the

demonstration board must be equipped with additional control and protective devices in

accordance with the applicable safety requirements (e.g. compliance with technical

equipment and accident prevention rules).

UM0969 Board description

Doc ID 17665 Rev 1 9/57

2 Board description

2.1 System architecture

A generic motor control system can be basically schematized as the combination of three

main blocks (see Figure 2):

●Control block: the main task of this block is to accept user commands and board\motor

configuration parameters. The control block provides all digital signals to implement the

right motor driving strategy. The STM3210B-EVAL, ST demonstration board, based on

an STM32 microcontroller, can be connected to the STEVAL-IHM027V1 thanks to the

onboard motor control connector

●Power block: this is based on three-phase inverter topology. The heart of the power

block is the STGIPS10K60A integrated intelligent power module which contains all the

necessary active components. Please refer to the STGIPS10K60A datasheet (see

References 1) for more information

●Power supply block: able to work from 90 VAC to 220 VAC or from 125 VDC to 350

VDC. Please refer to Section 3: Hardware setting of the STEVAL-IHM027V1, to

properly set the jumpers according to the required application

Figure 2. Motor control system architecture

The STEVAL-IHM027V1 includes the power supply and the power block.

UM0969 Board description

Doc ID 17665 Rev 1 10/57

2.2 Board schematics

Figure 3. Input stage with bridge schematic

!-V

5HOD\

5HOD\

%86





6OLTAGEDOUBLER6AC

--



&

9

&

9

--



--



&

Q)9;

&

Q)9;

55

N:

5

N:

5

--



--



-

9$&

-

9$&



5

N:N:

5

N:N:

)

$

)

$

&

9

&

9

-

9'&%86

-

9'&%86 



--



57

17&

57

17&

75

.($

75

.($

--





'

%5,'*(



'

%5,'*(









--



--



)

$

)

$

--



Inhaltsverzeichnis

Andere ST Hauptplatine Handbücher

ST STEVAL-BLUEPIRV1 Bedienungsanleitung

ST STEVAL-PCC008V1 Bedienungsanleitung

ST STEVAL-IHM011V1 Bedienungsanleitung

ST STMPE801 Bedienungsanleitung

ST STEVAL-OET001V1-LCP154DJF Bedienungsanleitung

ST UM1748 Bedienungsanleitung

ST PTB801DC Bedienungsanleitung

ST User Manual Bedienungsanleitung

ST EVAL-TDA7803A Bedienungsanleitung

ST STR730-EVAL Bedienungsanleitung

ST SPC560P-DISP Bedienungsanleitung

ST STEVAL-IHM020V1 Bedienungsanleitung

ST SPC58XXADPT144S REV.B Bedienungsanleitung

ST STM32L4R9I-EVAL Bedienungsanleitung

ST NUCLEO-F207ZG Bedienungsanleitung

ST SPC560D-DIS Bedienungsanleitung

ST STEVAL-SPIN3202 Bedienungsanleitung

ST X-NUCLEO-IKS01A1 Bedienungsanleitung

ST STM8L15LPBOARD Bedienungsanleitung

ST ST9 EPB Bedienungsanleitung

ST STM8T141-EVAL Bedienungsanleitung

ST STM32L152-EVAL Montage- und Bedienungsanleitung

ST STM32G474E-EVAL Bedienungsanleitung

ST NUCLEO-G070RB Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung