StarTech.com SV565UTPUSA Bedienungsanleitung

Console Extender over

Cat5 UTP

USB, VGA, Serial and Audio

Console Extender over Cat5

UTP

SV565UTPUSA

Instruction Manual

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide rea-

sonable protection against harmful interference in a residential installation. This equip-

ment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio com-

munications. However, there is no guarantee that interference will not occur in a particu-

lar installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.•

Increase the separation between the equipment and receiver.•

Connect the equipment into an outlet on a circuit different from that to which the receiver•

is connected.

Consult the dealer or an experienced radio/TV technician for help.•

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other

protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and

do not represent an endorsement of a product or service by StarTech.com, or an en-

dorsement of the product(s) to which this manual applies by the third-party company in

question. Regardless of any direct acknowledgement elsewhere in the body of this doc-

ument, StarTech.com hereby acknowledges that all trademarks, registered trademarks,

service marks, and other protected names and/or symbols contained in this manual and

related documents are the property of their respective holders.

Table of Contents

Introduction..................................................................... 1

Packaging Contents.....................................................................1

System Requirements .................................................................1

Installation....................................................................... 2

Hardware Installation...................................................................4

Driver Installation.........................................................................5

Conﬁguration .................................................................. 5

Serial Data Link ...........................................................................5

Automatic Calibration Button and Light .......................................5

Manual Calibration and Settings Menu........................................6

Commands ..................................................................................7

Transmitter Unit speciﬁc commands............................................7

Image Quality ..............................................................................8

Firmware Upgrade.......................................................................9

Troubleshooting .............................................................. 10

Speciﬁcations.................................................................. 12

Technical Support........................................................... 13

Warranty Information...................................................... 13

Introduction

Packaging Contents

1 x Transmitter unit•

1 x Receiver unit•

2 x Power Adapter•

1 x USB A-B cable•

1 x VGA extension cable (male/female)•

1 x Instruction Manual•

System Requirements

VGA and USB enabled computer system•

Standard 104-key USB keyboard•

Standard 3-button USB mouse•

VGA enabled monitor•

Additional Receiver units for cascaded operation•

Installation

Front View

Transmitter Unit

DE-15 VGA In (male)1.

3.5mm mini-jack audio In2.

3.5mm mini-jack microphone Out3.

USB type B host connector4.

DB9 RS-232 serial (female)5.

Receiver Unit

DE-15 VGA Out (male)1.

3.5mm mini-jack audio Out2.

3.5mm mini-jack microphone In3.

USB type A peripheral connectors4.

DB9 RS-232 serial (male)5.

Receiver Unit

Transmitter Unit

1 2 3 4 5

Rear View

Transmitter Unit

DC Power connector1.

RJ45 Link connector2.

3.5mm mini-jack Audio Out3.

DE-15 VGA Out (female)4.

Receiver Unit

DC Power connector1.

Setup button2.

RJ45 Link Out connector3.

RJ45 Link In connector4.

Receiver Unit

Transmitter Unit 12 3 4

1 2 3 4

Hardware Installation

Transmitter Unit

Connect USB cable between PC and USB-B. This also provides1.

power to the Transmitter Unit.

Optional: Connect the 5V power supply to Power In for backup or

if not using a USB cable. A 5V power adapter is required for the

Receiver Unit.

Connect VGA cable between PC and “Video In”.2.

Optional: Connect a monitor to the VGA “Video Out” port.

Connect the Cat5e cable from the RJ45 “Link” port to the ﬁrst3.

Receiver Unit in the series.

Optional:4. If transmitting audio, connect the speaker/line out on the

computer sound card to “Audio-In“ connector.

Optional:5. Connect speakers to the “Audio-Out” passthrough port.

Optional:6. If you wish to receive audio from a microphone, connect

the mic-in on the computer sound card to the “Mic-out” connector.

Optional:7. Connect the serial port on the computer to DB9 “Serial”

port using a straight-through cable.

Receiver Unit

Connect the 5V power supply to the “Power” connector.1.

Connect a monitor to the “VGA-Out” connector.2.

Connect a USB keyboard/mouse to the USB type A connectors.3.

Connect the Cat5e cable from Transmitter Unit to the “Link In” port.4.

To connect additional Receiver Units, connect a Cat5e cable from5.

the “Link Out” port, to the “Link In”, of any additional units.

Optional:6. Connect a microphone to the “Mic-In” port.

Optional:7. Connect speakers to the “Audio-Out” port.

Optional:8. Connect an RS-232 serial device to the “Serial” port.

Driver Installation

No drivers or additional software need to be installed on the host

computer.

Conguration

Serial Data Link

The SV565UTPUSA is able to link two RS232 ports together to allow

touchscreens, monitor control ports and other devices to be used

remotely. The port’s baud rate is detected automatically and supports

300 to 19200 bps, with 9600 being the preferred rate. If using a baud

rate other then 9600 it may take several bytes of data being sent to

properly calibrate it. By default the ﬁrst Receiver Unit has control of

the serial port, but any Receiver Unit can be accessed by using the

conﬁguration menu on the Transmitter Unit.

Automatic Calibration Button and Light

SV565UTPUSA is able to automatically calibrate to different cable

lengths in order to preserve image quality. This allows it to work out

of the box without any adjustments. Once a good calibration setting is

attained, it can be set into ﬁxed calibration mode. This ensures it uses

the same settings if it is reset or powered off.

The calibration button on the back of the Receiver Unit can be pressed

with the tip of a pen. The image will display a brief test pattern and the

indicator light will ﬂash. If it is held for more then half a second, it will

switch to ﬁxed calibration mode. In ﬁxed mode the indicator LED below

the button will light up and auto calibration will not occur in this state.

Press and hold the button again to return to auto calibration mode.

Manual Calibration and Settings Menu

A text-based menu is available on the serial port of both the Transmitter

and Receiver units. This can be used to make ﬁne adjustments to the

image quality. The menu can be accessed by connecting the serial port

to a PC or laptop using a straight-through cable for Transmitter Unit or

a null modem cable for Receiver Unit. For computers that don’t have

a serial port built in, the StarTech.com ICUSB232 can be used. You

can use any terminal communication software to connect to the serial

port, such as minicom for UNIX, and HyperTerminal or TeraTerm for

Windows.

If the serial data link is being used, the Transmitter Unit will already

be set up for serial communication. To connect to a Receiver Unit the

serial device must be unplugged ﬁrst and replaced with the RS232 null

modem cable. Use the same baud rate that the serial device and PC

had used to communicate.

If you are not using the serial link just attach the RS232 cable and use

9600 bps. Also conﬁgure the terminal software to use 8N1, or 8 bits

with no parity and 1 stop bit.

An escape code is used to enter the serial menu from data transfer

mode. The code is a one second delay, followed by 3x @ symbols,

then another one second delay. A conﬁrmation message will appear if

it works. If it does not appear, try again a few times because it depends

on timing. To exit the menu press X to return to data transfer mode.

Commands are case sensitive.

The Transmitter Unit is able to access all of the Receiver units attached

to it, allowing changes to be made from a central location. Also the

Transmitter Unit can change which Receiver Unit has the serial link

enabled. Receiver units can change their own settings, allowing for

ﬁne-tuning to be made in the ﬁeld using a laptop.

Commands

h - Help, show all commands

p - Print settings

f - Auto calibration enable

F - Fixed conﬁg enable. Use this to lock in the settings after adjusting

Auto calibrate next Receiver Unit in the chain. Use this after youn -

make any adjustments to vCtrl or gain

z/x - Decrease/increase gain for brightness

c/v - Decrease/increase vCtrl for distance compensation

a/s - Decrease/increase Red skew compensation

q/w - Decrease/increase Green skew compensation

1/2 - Decrease/increase Blue skew compensation

0 - Restore factory default settings and recalibrate

R - Reset device

X - Exit menu and restore serial link mode

Transmitter Unit specic commands

Get calibration from a certain Receiver unit. You must do this ﬁrstg -

in order to change any settings. Type the desired Receiver Unit

address and then Enter

Select which Receiver Unit gets the serial port link to ther -

Transmitter Unit

The ﬁrst Receiver Unit has address 1, the second has address 2, etc.

Gain adjusts the brightness of the signal caused by losses in the cable.

This does not normally need to be ﬁne tuned, it is better to adjust

the monitor’s settings if it is too dark, too bright or has color balance

problems.

Andere Handbücher für SV565UTPUSA

Inhaltsverzeichnis

Andere StarTech.com Extender Handbücher

StarTech.com

StarTech.com ST121HDBTPW Bedienungsanleitung

StarTech.com

StarTech.com USBthere USB201EXT Bedienungsanleitung

StarTech.com

StarTech.com SV565UTP Bedienungsanleitung

StarTech.com

StarTech.com ST121HDBTU Bedienungsanleitung

StarTech.com

StarTech.com USBthere USB204EXT Bedienungsanleitung

StarTech.com

StarTech.com 110VDSLEXT2 Bedienungsanleitung

StarTech.com

StarTech.com USBthere USB221EXT Bedienungsanleitung

StarTech.com

StarTech.com POEEXT1GAT Bedienungsanleitung

StarTech.com

StarTech.com 0065030863223 Bedienungsanleitung

StarTech.com

StarTech.com ST121HD20V Bedienungsanleitung

StarTech.com

StarTech.com 8STST12MHDLAN Bedienungsanleitung

StarTech.com

StarTech.com ST12MHDLNHR Bedienungsanleitung

StarTech.com

StarTech.com ST121HDBT20L Bedienungsanleitung

StarTech.com

StarTech.com USB3004EXT2 Bedienungsanleitung

StarTech.com

StarTech.com 410VDSLEXT Bedienungsanleitung

StarTech.com

StarTech.com ST121UTP23GB Bedienungsanleitung

StarTech.com

StarTech.com 410VDSLEXT2 Bedienungsanleitung

StarTech.com

StarTech.com IREXT Bedienungsanleitung

StarTech.com

StarTech.com ST121HDBTPW Bedienungsanleitung

StarTech.com

StarTech.com USB2004EXTV Bedienungsanleitung

StarTech.com

StarTech.com ST121R Bedienungsanleitung

StarTech.com

StarTech.com ST121UTP Bedienungsanleitung

StarTech.com

StarTech.com SV565UTPHDU Bedienungsanleitung

StarTech.com

StarTech.com ST121WHDS Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung