Stelpro STCP Bedienungsanleitung

INSSTCP1010

“STCP”

Heating Floor Programmable

Electronic Thermostat

User’s Guide

www.stelpro.com

For further information or to consult this guide online,

please visit our Web site.

INSSTCP1010

1.Description

The STCP electronic thermostat can be used to control heating

ﬂoors with electrical current − with a resistive load − ranging from

0 A to 16 A at 120/208/240 VAC. It has an easy user interface

and can manage up to four programming periods a day. It keeps

the temperature of a room ( mode) and a ﬂoor ( mode) at

a requested set point with a high degree of accuracy.

Floor Mode (factory setting): this control method is ideal

in areas where you want a hot ﬂoor at any time and when the

temperature of the ambient air can be high without causing dis-

comfort. For example, in a bathroom.

WARNING WARNING

Before installing and operating this product, the

owner and/or installer must read, understand and fol-

low these instructions and keep them handy for fu-

ture reference. If these instructions are not followed,

the warranty will be considered null and void and the

manufacturer deems no further responsibility for this

product. Moreover, the following instructions must

be adhered to in order to avoid personal injuries

or property damages, serious injuries and poten-

tially fatal electric shocks. All electric connections

must be made by a qualiﬁed electrician, according to

the electrical and building codes effective in your re-

gion. Do NOT connect this product to a supply source

other than 120 VAC, 208 VAC or 240 VAC, and do not

exceed the speciﬁed load limits. Protect the heating

system with the appropriate circuit breaker or fuse.

You must regularly clean dirt accumulations on or in

the thermostat. Do NOT use ﬂuid to clean thermostat

air vents. Do NOT use where exposed to water. Suitable

for insulated walls.

INSSTCP1010

Ambient Mode (you only have to press down the A/F but-

ton to switch from one mode to the other): this control method

is ideal when you want a stable ambient air temperature (without

ﬂuctuation). Usually, this mode is used in large and often occu-

pied rooms where temperature variations can be uncomfortable.

For example, in a kitchen, a living room or a bedroom.

Some factors cause variations in ambient air temperature. They

include large windows (heat losses or gains due to outside tem-

perature) and other heat sources such as a central heating sys-

tem, a ﬁreplace, etc. In all these cases, the mode will ensure

a uniform temperature.

This Thermostat is not Compatible with the Following

Installations:

•electricalcurrenthigherthan16Awitharesistiveload(3840W

@240VAC,3475W@208VACand1920W@120VAC);

•inductiveload(presenceofacontactororrelay);and

•centralheatingsystem.

Parts Supplied:

•one(1)thermostat;

•two(2)mountingscrews;

•four(4)solderlessconnectorssuitableforcopperwires;

•one(1)oorsensor.

2. Installation

Selection of Thermostat and Sensor Location

The thermostat must be mounted on a connection box, at

around1.5m(5feet)abovetheoorlevel,onasectionofthe

wall exempt from pipes or air ducts.

Do not install the thermostat in a location where tempera-

ture measurements could be altered. For example:

•closetoawindow,onanexternalwall,orclosetoadoorlead-

ingoutside;

•exposeddirectlytothelightorheatoftheSun,alamp,are-

INSSTCP1010

placeoranyotherheatsource;

• closeorinfrontofanairoutlet;

•closetoconcealedductsorachimney;and

•in a location with poor air ow (e.g. behind a door), or with

frequent air drafts (e.g. head of stairs).

To install the sensor, refer to the installation guide of your heat-

ing ﬂoor.

Thermostat Mounting and Connection

1. Cut off power supply on lead wires at the electrical

panel in order to avoid any risk of electric shock;

2. Ensure that the air vents of the thermostat are clean and clear

ofanyobstruction;

3.Usingascrewdriver,loosenthescrewretainingthemounting

base and front part of the thermostat. Remove the front part of

thethermostatfromthemountingbasebytiltingitupward;

INSSTCP1010

4. Align and secure the mounting base to the connection box

usingthetwoscrewssupplied;

5.Route wires coming from the wall through the hole of the

mounting base and make the required connections using the

“Four-wire installation” ﬁgure, and using the supplied solder-

less connectors. A pair of wires (black) must be connected

to the power source (120-208-240 VAC) and another pair

(yellow) must be connected to the heating cable (refer to the

drawings displayed on the back of the thermostat). For con-

nections with aluminum wires, you must use CO/ALR connec-

tors. Please note that thermostat wires do not have polarity,

meaning that any wire can be connected to the other. Then,

installtheoortemperaturesensor;

Four-wire installation

INSSTCP1010

6. Reinstall the front part of the thermostat on the mounting base

andtightenthescrewatthebottomoftheunit;

7.Turnonthepower;

8. Set the thermostat to the desired setting (see the following

section).

3. Operation

INSSTCP1010

First Start-up

At the ﬁrst start-up, the thermostat is initially in the Man (manual)

and modes. The temperature is displayed in degrees Celsius

and the standard factory set point adjustment is 21°C. The hour

displays --:-- and must be adjusted before switching to the Auto

or Pre Prog mode. The maximum ﬂoor temperature is limited

to 28°C.

Ambient and Floor Temperature

The ﬁgures displayed below the icon indicate the ambi-

ent temperature, ±1 degree. The ﬁgures displayed below the

icon indicate the ﬂoor temperature, ±1 degree. Both tem-

peratures can be displayed in degrees Celsius or Fahrenheit (see

“Display in degrees Celsius/Fahrenheit”).

Temperature Set Points

The ﬁgures displayed beside the icon indicate the ambient

() or the ﬂoor ( ) temperature set points. They can be dis-

played in degrees Celsius or Fahrenheit (see “Display in degrees

Celsius/Fahrenheit”).

Out of any adjustment mode, press down the + button to in-

crease the set point, or the - button to decrease it. Set points

can only be adjusted by increments of 1 degree. To quickly scroll

through the set point values, press and hold down the button.

Maximum Floor Temperature Limitation

At any time, the ﬂoor temperature (in mode) is maintained at

less than 28°C (82°F) in order to avoid overheating caused by an

excessive heating request, which could damage some materials

or be detrimental for health.

Adjustment of the Hour and the Day of the Week

Adjustment procedure of the hour and the day of the week.

1.Press down the Day/Hr button, whether it is in Man, Auto or

Pre Prog mode.

2.At this moment, the icon and the day of the week blinks and

you can adjust the day of the week using the + or - button and

INSSTCP1010

conﬁrm your choice by pressing down the Mode or Day/Hr

button. You can also press down the desired day of the week

button without using the + or - button and conﬁrm your choice

using the Mode or Day/Hr button.

3.Thetwoguresindicatingthehourblink.Youmustadjustthem

using the + or - button and conﬁrm your choice by pressing

down the Mode or Day/Hr button.

4.The two ﬁgures indicating the minutes blink. You must adjust

them using the + or - button and conﬁrm your choice by press-

ing down the Mode or Day/Hr button. The adjustment is then

completed and the thermostat returns to the previous mode.

At any time, you can exit the adjustment mode of the day and the

hour by pressing down the Exit button or by not pressing any

button during 1 minute.

In case of a power failure, the thermostat is self-sufﬁcient for 2

hours. If the failure lasts less than 2 hours, the thermostat saves

the adjustment of the hour and the day of the week. When the

power is restored after an extensive failure (more than 2 hours),

the hour and the day of the week are recovered, but you must

update them.

Display in Degrees Celsius/Fahrenheit

The thermostat can display the ambient temperature and the set

point in degrees Celsius (standard factory setting) or Fahrenheit.

Adjustment procedure for degrees Celsius/Fahrenheit display.

1.To switch from the degrees Celsius to the degrees Fahrenheit,

and conversely, simultaneously press down the + and - but-

tonsformorethan3secondsuntilthe icon blinks.

2.Press down the + button to switch from the degrees Celsius to

the degrees Fahrenheit, and conversely. The degree Celsius or

Fahrenheit symbol is displayed.

3.Whentheadjustmentiscompleted,pressdowntheExitbut-

tonordonotpressdownanybuttonduring5secondstoexit

the adjustment function.

INSSTCP1010

This adjustment can be done from any of the three principal

modes.

Manual Mode (Man)

From the Manual mode, you can manually adjust the thermostat

set point by pressing down the + or - buttons to increase the

value, or to decrease it. Please note that if the backlight is off,

the set point will not change when you press down these but-

tons for the ﬁrst time instead, the backlight will be activated. To

quickly scroll through the set point values, press and hold down

the button. From mode,thesetpointscanrangebetween3

and35°Candcanonlybeadjustedbyincrementsof1°C(from

37 to 95°F; by increments of 1°F from the Fahrenheit mode).

From mode,thesetpointscanrangebetween3and28°C

(from 37 to 82°F). The thermostat will turn off if the set point

isloweredbelow3°C(37°F),andthesetpointvaluedisplayed

will be --. The standard factory set point adjustment is 21°C

(mode). From this mode, the screen displays the /

mode temperature, the /mode set point, the hour and

the day of the week.

This mode is initially activated when the power is turned on for the

ﬁrst time. You must adjust the hour (as described in the section

“Adjustment of the hour and the day of the week”) before switching

to other modes by pressing down the Mode or Pre Prog button.

Automatic Mode (Auto)

To switch from the Manual mode to the Automatic mode, and

conversely, press down the Mode button. The Man or Auto icon

is displayed at the bottom of the screen as applicable.

From the Automatic mode, the thermostat adjusts the set points

according to the programmed periods. If no data is entered, the

thermostat acts as in Manual mode and the standard factory

set point adjustment is 21°C ( mode). It is always possible

to manually adjust the set point using the + or - button. The se-

lected set point will be effective until one period is programmed,

which represents an hour and a day of the week. Note that, if

the set point is lowered to off (--), the programming will not be

effective. It is possible to program 4 periods a day, meaning that

INSSTCP1010

the set point can change automatically up to 4 times a day. The

period order is not important.

From this mode, the screen displays the temperature, the set

point, the hour, the day of the week and the current programmed

periodnumber(1to4;asapplicable).

After programming a day of the week, you can copy this setting;

see “Copy of the Programming”.

1.To access the Programming mode, press down the day of the

week button that you want to program (Mon to Sun). Once you

release the button, the selected day of the week is displayed,

the icon blinks and the period number 1 blinks too.

2.Select the period number (1 to 4) that you want to program us-

ing the + or - button. For each period, the hour and the set point

are displayed. The hour displays --:-- and the set point displays

-- if there is no programming for the period. You must conﬁrm

the period by pressing down the Mode button.

3.Thetwoguresrepresentingthehourblinktoindicatethatyou

canadjustthem(from00to23)usingthe+or–button.Youmust

conﬁrm the adjustment by pressing down the Mode button.

4. After conﬁrmation, the ﬁgures representing the minutes (the

last 2 ﬁgures) blink. You can adjust and conﬁrm them in the

mannerdescribedinpoint3.Notethattheminutescanonly

beadjustedbyincrementsof15minutes.

5.The period set point blinks and you can adjust it using the

+ or - button. You must conﬁrm the adjustment by pressing

down the Mode button.

6.After set point conﬁrmation, the programming is completed.

The following period number blinks. For example, if the previ-

ously programmed period was 1, period 2 blinks. It is then

possible to continue the programming of this period by press-

ing down the Mode button. You can also select another period

usingthe+or–button.

7.Attheendofperiod4programming,youautomaticallyexitthe

Programming mode.

Andere Handbücher für STCP

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Stelpro Thermostat Handbücher

Stelpro

Stelpro B2T1 Series Bedienungsanleitung

Stelpro

Stelpro B1T1ER Bedienungs- und Wartungshandbuch

Stelpro

Stelpro MAESTRO Bedienungsanleitung

Stelpro

Stelpro ET180 Bedienungsanleitung

Stelpro

Stelpro Allia ASAT402ZB Bedienungsanleitung

Stelpro

Stelpro STCNP - 5mA Bedienungsanleitung

Stelpro

Stelpro MAESTRO Bedienungsanleitung

Stelpro

Stelpro STE302PA Bedienungsanleitung

Stelpro

Stelpro STCNP Bedienungsanleitung

Stelpro

Stelpro B1T1 Series Bedienungsanleitung

Stelpro

Stelpro Maestro SMC402 Bedienungsanleitung

Stelpro

Stelpro STE302P Bedienungsanleitung

Stelpro

Stelpro SHUT1 Series Bedienungsanleitung

Stelpro

Stelpro STE302NP Bedienungsanleitung

Stelpro

Stelpro Allia SAT402ZB Bedienungsanleitung

Stelpro

Stelpro STE241 Bedienungsanleitung

Stelpro

Stelpro STCP Bedienungsanleitung

Stelpro

Stelpro BA Series Bedienungsanleitung

Stelpro

Stelpro Maestro SMT402 Bedienungsanleitung

Stelpro

Stelpro STE362RNP Bedienungsanleitung

Stelpro

Stelpro MAESTRO Bedienungsanleitung

Stelpro

Stelpro T12 Series Bedienungsanleitung

Stelpro

Stelpro MAESTRO Bedienungsanleitung

Stelpro

Stelpro STE403NP Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Honeywell

Honeywell T6811 Bedienungsanleitung