Stelpro STZB402 Plus Bedienungsanleitung

For further information or to consult this guide online, please visit our website at www.stelpro.com 042D07_INSSTZB402+0616

USER’S GUIDE

STZB402+

ELECTRONIC THERMOSTAT FOR THE SMART HOME

042D07_INSSTZB402+0616

WARNING

Before installing and operating this product, the owner and/or installer must read, understand

and follow these instructions and keep them handy for future reference. If these instructions

are not followed, the warranty will be considered null and void and the manufacturer deems no

further responsibility for this product. Moreover, the following instructions must be adhered to

in order to avoid bodily harm or property damages, serious injuries and potentially fatal electric

shocks. All electric connections must be made by a qualied electrician, according to the electric

and building codes effective in your region.

Do NOT connect this product to a supply source other than 120 VAC or 240 VAC, and do

not exceed the load limits specied. Protect the heating system with the appropriate circuit

breaker or fuse. You must regularly clean dirt accumulations on the thermostat. Do NOT use

uid to clean thermostat air vent. Do not install thermostat in a wet place. However, installing it

in insulated walls is allowed.

NOTE: When a part of the product specification must be changed to improve operability or other

functions, priority is given to the product specification itself. In such instances, the instruction

manual may not entirely match all the functions of the actual product.

Therefore, the actual product and packaging, as well as the name and illustration, may differ from

the manual.

The screen/LCD display shown as an example in this manual may be different from the actual

screen/LCD display.

042D07_INSSTZB402+0616

This thermostat is designed to control baseboard, convector and fan-forced heaters. It may be

associated to a ZigBee network.

This thermostat is NOT compatible with the following installations

• Inductive load

• Central heating system

• Heating load outside the specified ratings (refer to the Technical Specifications section)

Parts supplied

• one (1) thermostat

• one (1) wall mounting plate located at the back of the thermostat

• two (2) mounting screws

• two (2) solderless connectors suitable for copper wires

Selection of the thermostat location

The thermostat must be mounted to a connection box on a wall facing the heating unit, at around 1.5 m

(5 feet) above the floor level, on a section of the wall exempt from pipes or air ducts.

Do not install the thermostat in a location where temperature measurements could be altered. For

example:

• close to a window, on an external wall, or close to a door leading outside

• exposed directly to the light or heat of the sun, a lamp, a fireplace or any other heat source

• close to or in front of an air outlet

• close to concealed ducts or a chimney

• in a location with poor air flow (e.g. behind a door) or with frequent air drafts (e.g. head of stairs)

DESCRIPTION

INSTALLATION

042D07_INSSTZB402+0616

Thermostat mounting and connection

1. Cut off power supply on lead wires at the electrical panel in order to avoid any risk of electric

shock.

2. If an existing thermostat is being replaced, remove the previous thermostat.

3. Ensure that the air vents of the Ki thermostat are clean and clear of any obstruction.

4. Using a screwdriver, loosen the screw retaining the mounting base of the thermostat (do not

completely remove the screw).

Then, remove the mounting base at the back of the thermostat by tilting it downward, then towards you.

5. Align and secure the mounting base to the connection box using the two screws supplied.

042D07_INSSTZB402+0616

6. Pass the wires from the wall through the hole at the base of the mounting base and connect them

using the solderless connectors supplied. When making the connection with aluminum wire,

make sure that you are using connectors identified CO/ALR. Please note that the thermostat

wires do not have polarity. Therefore, the way they are connected is not important.

2-WIRE INSTALLATION

4-WIRE INSTALLATION

042D07_INSSTZB402+0616

7. Place all the wires into the connection box.

8. Align the little slots located on the top of the thermostat with those on the mounting base and

secure the thermostat to the mounting base. Note that you can also position the thermostat on

the left or the right side of the junction box (see below). Then tighten the screw at the bottom of

the unit.

9. Turn the power on.

ALIGNMENT

042D07_INSSTZB402+0616

Ambient temperature

Heating status

Thermostat mode

Advanced settings

Set point temperature OR

outdoor temperature

(requires external

sensor over ZigBee)

Fan mode

Lock mode

Frost warning

ZigBee connectivity

OPERATION

042D07_INSSTZB402+0616

Ambient temperature

The temperature is displayed either in °C with a 0.5 °C resolution or in °F with a 1 °F resolution.

The screen will display LO if the temperature drops below 0 °C (32 °F) and will display HI if the

temperature rises above 50 °C (122 °F).

Temperature setpoints

The setpoint may be edited by the user using the UP and DOWN buttons located on the thermostat.

The setpoint may also be modified through the ZigBee network.

The minimum setpoint is 5 °C (41 °F) and the maximum setpoint is 30 °C (86 °F).

NOTE: if the setpoint is set at 7 °C (45 °F) or below, the frost warning icon will be displayed to

warn the user that water pipes might be subject to freezing.

Heating power indicator

Whenever the thermostat is actively heating the room, the heating status graph will display the

heating percentage.

No bar: 0%

1 bar: 1-25%

2 bars: 26-50%

3 bars: 51-75%

4 bars: 76-100%

Thermostat mode

The thermostat has three modes: Comfort, Eco and Off. The first two modes have their own

preestablished setpoint. Comfort: 21 °C (70 °F), Eco ( ): 17 °C (63 °F).

The user may change the setpoint to any value in the range described in the setpoint section.

When the Eco mode is active, the Eco icon ( ) is displayed on the LCD. When the Off mode

is active, the frost warning icon is displayed on the LCD and the setpoint is replaced by ( -- ).

The thermostat mode may be changed locally on the thermostat by pressing the UP and DOWN

buttons simultaneously for less than 3 seconds while on the main screen. The Eco setpoint is local

to the thermostat and cannot be edited through the ZigBee network.

If a setpoint change is sent through the ZigBee network, the thermostat mode will automatically

switch to Comfort mode.

042D07_INSSTZB402+0616

NOTE 1: Even in Off mode , the thermostat is still powered and electric shock is still possible.

Always cut off the power supply when cleaning or removing the thermostat.

NOTE 2: When in Off mode , the thermostat will not activate the heating element, therefore there

is a risk of freezing.

Heating mode

The thermostat has two heating modes: Baseboard/convector heater and Fan-forced heater.

The Baseboard/convector heater mode will drive the load with a 15-second cycle while the Fan-forced

heater mode will drive the load with a 5-minute cycle.

When the Fan-forced heater mode is selected, the fan icon is displayed on the thermostat.

ZigBee connectivity ()

If the thermostat is associated to a ZigBee network, the connectivity icon will be displayed on the LCD,

if the device is removed from a ZigBee network, the connectivity icon will disappear. The connectivity

icon may blink if there is an issue with the ZigBee radio circuit.

Advanced settings ( )

There are 7 advanced settings menus on the thermostat.

The advanced settings are the following:

1. ZigBee menu : used to associate or remove the thermostat from a ZigBee network

2. Display format: used to switch the temperature format between °C and °F

3. Heating mode : used to switch the heating mode between Baseboard/convector and Fan-

forced heaters

4. Lock mode : used to lock the thermostat to prevent unauthorized tampering.

5. Outdoor temperature display : used to switch the outdoor temperature display on or off

(when available). When set to (On), the outdoor temperature will be displayed if it’s available.

When set to (Off), the outdoor temperature will not be displayed and the setpoint will always

be displayed.

6. Backlight status while idle: used to set the backlight intensity when the thermostat is idle.

0%: the backlight will turn off after 15 seconds of inactivity

50%: the backlight will dim to 50% after 15 seconds of inactivity

100%: the backlight will always be at full intensity

042D07_INSSTZB402+0616

7. °STELPRO information menu: used to gain information on the product

7.1: Thermostat version

7.2: ZigBee radio version

7.3: Day of production

7.4: Month of production

7.5: Year of production

7.6: Baseboard/convector control checksum

7.7: Fan-forced heater control checksum

- ZigBee node Id

- ZigBee network Id

- Reset to default

Modification of the settings:

- To gain access to the advanced settings root menu, press the UP and DOWN buttons

simultaneously for 3 seconds.

- At this point each setting (1 to 7) may be accessed by using the UP and DOWN buttons.

- To edit a value, choose a setting then simultaneously press the UP and DOWN buttons once.

Press the UP or DOWN button to edit the value.

- Confirm your choice by pressing the UP and DOWN buttons simultaneously one time at which

point the icon will momentarily flash rapidly if a change has been made.

- To exit the advanced settings press the UP and DOWN buttons simultaneously for 3 seconds at

any time. If the thermostat is left idle it will revert back to the main screen after 30 seconds

ZigBee network association ( )

Association:

Make sure the ZigBee controller is in pairing mode (refer to your ZigBee controller instruction manual).

To associate the thermostat to a ZigBee network, enter Menu 1 (ZigBee menu) and either select

(On) or the specific ZigBee channel used by your ZigBee controller (11 to 26). Then press the UP

and DOWN buttons to start the association process. During association, (On) or the specific channel

will be blinking and the connectivity icon will be animated in an increasing pattern. When the

association process has been completed, the associated channel number will be displayed solid. If an

error occurs, (Err) will be displayed for 3 seconds then the screen will revert to (Off).

Inhaltsverzeichnis

Andere Stelpro Thermostat Handbücher

Stelpro

Stelpro STE402NP Bedienungsanleitung

Stelpro

Stelpro Maestro SMT402 Bedienungsanleitung

Stelpro

Stelpro STE402P Bedienungsanleitung

Stelpro

Stelpro STE362RNP Bedienungsanleitung

Stelpro

Stelpro 360 comfort D070 Bedienungsanleitung

Stelpro

Stelpro Maestro SMC402 Bedienungsanleitung

Stelpro

Stelpro ET180 Bedienungsanleitung

Stelpro

Stelpro Maestro ASMT402 Bedienungsanleitung

Stelpro

Stelpro Maestro SMT402AD Bedienungsanleitung

Stelpro

Stelpro STE362RNP Bedienungsanleitung

Stelpro

Stelpro ASMC402 Bedienungsanleitung

Stelpro

Stelpro STE402NP Bedienungsanleitung

Stelpro

Stelpro MAESTRO Bedienungsanleitung

Stelpro

Stelpro STCNP Bedienungsanleitung

Stelpro

Stelpro STE403NP Bedienungsanleitung

Stelpro

Stelpro T12 Series Bedienungsanleitung

Stelpro

Stelpro B1T1 Series Bedienungsanleitung

Stelpro

Stelpro SHUT1 Series Bedienungsanleitung

Stelpro

Stelpro STE402P Bedienungsanleitung

Stelpro

Stelpro STE241 Bedienungsanleitung

Stelpro

Stelpro MAESTRO Bedienungsanleitung

Stelpro

Stelpro STE252NP+ Bedienungsanleitung

Stelpro

Stelpro B1T1ER Bedienungs- und Wartungshandbuch

Stelpro

Stelpro Maestro SMC402AD Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Honeywell

Honeywell T6811 Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung