STMicroelectronics STEVAL-MKI109V2 Bedienungsanleitung

Introduction

The STEVAL-MKI109V2 (eMotion) is a motherboard designed to provide the user with a complete ready-to-use platform for the

demonstration of MEMS devices mounted on adapter boards.

The STEVAL-MKI109V2 uses an STM32F103RET6 microcontroller which functions as a bridge between the sensor on the

adapter board and the PC on which it is possible to use the Unico graphical user interface (GUI) downloadable from the ST

website or dedicated software routines for customized applications.

This user manual describes the hardware included with the demonstration kit and provides the information required to install the

demonstration board and how to upgrade the firmware of the microcontroller.

For details regarding the features of each sensor, please refer to the datasheet available for each individual device.

STEVAL-MKI109V2: eMotion motherboard for MEMS adapter boards

UM0979

User manual

UM0979 - Rev 6 - February 2018

For further information contact your local STMicroelectronics sales office.

www.st.com/

1 Demonstration kit description

The eMotion is a complete demonstration kit that allows demonstration of both digital and analog MEMS sensors.

Thanks to its DIL 24 connector, a wide range of MEMS adapter boards can be used.

The block diagram of the demonstration kit is shown in Figure 1. Demonstration board block diagram.

Figure 1. Demonstration board block diagram

Control Switches

(reset, left, right)

MEMS

device

USB

Connector

SPI/I C/

U.S.B.

Analog

Controls

(ST,PD,FS)

Power On LED

Interrupt LEDs

General Purpose LEDs

With DFU

Feature

DIL 24

Connector

Analog

(ADC)

STM32F103RET6 µC

As shown in the Figure 1. Demonstration board block diagram, the eMotion demonstration kit is based on the

STM32F103RET6 microcontroller and can be connected to the PC through the USB bus. Data coming from the

MEMS sensor connected to the board can be read through the PC GUI provided with the kit.

The eMotion also implements the DFU (device firmware upgrade) feature, therefore, in the case of a new

firmware release, it can be reprogrammed without the need to use a programmer. See www.st.com/mems for new

firmware releases.

The eMotion also integrates three general-purpose LEDs, two LEDs connected directly to the interrupt pins of

digital adapters and the power/USB LED. Moreover, the eMotion integrates three buttons: two are available to the

user on a dedicated GPIO of the microcontroller, while the other is used as reset for the microcontroller.

All the MEMS adapter pins are available on two connectors placed on the board (Figure 2. Top silkscreen of the

eMotion kit JP2 and JP3).

The top silkscreen view and image of the full board are shown in Figure 2. Top silkscreen of the eMotion kit and

Figure 3. Board top view respectively.

UM0979

Demonstration kit description

UM0979 - Rev 6 page 2/39

Figure 2. Top silkscreen of the eMotion kit

UM0979

Demonstration kit description

UM0979 - Rev 6 page 3/39

Figure 3. Board top view

In order to use the eMotion demonstration kit, installation of a dedicated driver is required, which is included in the

installation pack, together with a GUI interface which allows simple interaction with the sensor. The steps required

for driver and software installation are described in the following sections.

In Figure 3. Board top view some main components placed on the top layer of the eMotion kit are highlighted.

• Jumpers JP9 and JP10 (Figure 3. Board top view, ref 10, ref 11) are used to select the STM32 boot mode.

When the eMotion is used together with MEMS adapters, JP9 and JP10 must be fitted (see STM32

datasheet for more information).

• Jumper J2 (Figure 3. Board top view, ref 7) can be used to directly supply the board (from 3.5 V to 6 V)

instead of using the USB connector.

• Jumper JP1 allows the user to measure the sensor current consumption by connecting a multimeter in

series with its terminals (Figure 3. Board top view, ref 9).

• Jumpers JP4, JP5, and JP6 (Figure 3. Board top view, ref 8) are used to manually set some features which

are available for just some of the analog MEMS adapters (see Table 1. Jumper configuration for power-down

(PD), self test (ST), and high-pass filter reset (HP) for more details). JP4 is used to set the self-test feature,

JP5 to handle the power-down pin, and JP6 to reset the MEMS high-pass filter. When they are fitted on pins

2-3, these functions are handled by the firmware itself.

UM0979

Demonstration kit description

UM0979 - Rev 6 page 4/39

Table 1. Jumper configuration for power-down (PD), self test (ST), and high-pass filter reset (HP)

Jumper on 1-2 position Jumper on 2-3 position Jumper unfitted

JP4

logic level 1:

self-test ON Self-test is handled by the firmware logic level 0:

self-test OFF, default

JP5

logic level 1:

power-down mode Power-down is handled by the firmware logic level 0:

normal mode, default

JP6

HP logic level 1: external high-pass filter reset High-pass filter reset is handled by the firmware logic level 0:

normal mode, default

• J1 connector (Figure 3. Board top view, ref 3) can be used to both reprogram the STM32 and to debug the

code through the JTAG or SWD protocols.

• Jumper JP7 (Figure 3. Board top view, ref 4) is used to select either JTAG (JP7 unfitted) or SWD (JP7 fitted)

mode.

• eMotion also integrates six LEDs and three buttons:

– LED D1 (Figure 3. Board top view, ref 6) is switched on when the board is power supplied.

– LEDs D2 and D3 (Figure 3. Board top view, ref 13) are directly connected to the interrupt pins of the

MEMS digital adapters (if available on the sensor mounted on the adapter board).

– LEDs D4, D5, and D6 (Figure 3. Board top view, ref 12) are general-purpose LEDs and are used to

indicate firmware states. For example, LED D6 is switched on when a specific firmware is selected

from those available. LED D5 on indicates that the microcontroller is well configured for communication

with the sensor. Finally the LED D4 blinks according to the sensor data rate selected.

– Button SW3 (Figure 3. Board top view, ref 1) is used to reset the STM32.

– Button SW1 and SW2 (Figure 3. Board top view, ref 2 and ref 5) are connected to STM32 GPIOs and

are available to the user.

Figure 4. How to connect the DIL24 adapter board to the STEVAL-MKI109V2 shows how to properly mount the

DIL24 adapter board on the STEVAL-MKI109V2 board.

UM0979

Demonstration kit description

UM0979 - Rev 6 page 5/39

Figure 4. How to connect the DIL24 adapter board to the STEVAL-MKI109V2

UM0979

Demonstration kit description

UM0979 - Rev 6 page 6/39

2 eMotion board installation

The software package can be downloaded from the st.com website and includes the following directory structure:

• DRIVER: it contains the installation package for the USB drivers needed to connect the eMotion board to the

PC. No driver is needed on Linux and Mac OS platforms, so this directory is included in the Windows

installation package only.

• DFU: it contains the .dfu files and the installation package for the software needed to upgrade the firmware

of the eMotion board.

• FIRMWARE: it contains the source code of the firmware of the eMotion board together with the

corresponding binary file that can be flashed to the board using the DFU software.

The section below describes the procedure to install the driver for the eMotion board (needed on Windows

platforms only) and the DFU software.

2.1 Hardware installation (Windows platforms)

No driver installation is needed on Linux and Mac OS platforms.

To install the STM32 virtual COM port driver on Windows platforms, launch the “VCPDriver_V1.4.0_Setup.exe”

included in the Windows installation package under the “DRIVER” folder and follow the instructions on the screen.

Once the driver is installed, insert the demonstration kit board into a free USB port. A notification message should

appear, as in Figure 5. Notification message.

Figure 5. Notification message

Now the eMotion should be recognized by the PC as a virtual COM. In order to confirm which COM port has been

assigned to the board, right click on “My Computer” and select “Manage”, select “Device Manager” and scroll

through the list until “Ports (COM & LPT)”. In the following example (Figure 6. Virtual COM port assignment) the

COM11 has been assigned to the board.

UM0979

eMotion board installation

UM0979 - Rev 6 page 7/39

Figure 6. Virtual COM port assignment

2.2 DFU

The MEMS STEVAL-MKI109V2 demonstration board is capable of reprogramming an application through the

USB, in accordance with the DFU class specification defined by the USB Implementers Forum. This capability is

useful because it allows reprogramming the microcontroller directly in the field and is particularly well-suited to

USB applications where the same USB connector can be used both for the standard operating mode and for the

reprogramming process.

In order to configure the eMotion board in DFU mode button SW2 must be pressed before supplying the board

and released when the LEDs D1, D4, D5, and D6 light up.

If the firmware version in use is lower than V3.0.0, it’s mandatory to patch the DFU feature using the

“DFU_Patcher_V1.0.2.dfu” file available under the “DFU” folder before proceeding with the upgrade of the

firmware with a version equal to or higher than V3.0.0. The procedure to patch the DFU feature corresponds to

the one used during a standard firmware upgrade with the DFU tool. At the end of this procedure, if the green

LED D4 is on, it indicates that the procedure is successfully completed; if the red LED D5 is on, the procedure

failed and has to be repeated. Before proceeding with the new firmware upgrade the board must be reset using

the SW3 button.

2.2.1 DFU on Windows

To install the DFU software, launch the “DfuSe_Demo_V3.0.5_Setup.exe” included in the software package under

the “DFU” folder and follow the instructions on the screen. To launch the software, select “Start >

STMicroelectronics > DfuSe > DfuSe Demonstration”.

In the ‘Upgrade or Verify Action’ section of the Dfuse Demo tool click on the ‘Choose...’ button and select the

target .dfu file; then click the ‘Upgrade’ button to start the firmware upgrade.

For more details regarding DFU and the microcontroller ST GUI, see the related user manual located under “Start

> STMicroelectronics > DfuSe > Docs > DfuSe Getting Started”.

UM0979

DFU

UM0979 - Rev 6 page 8/39

2.2.2 DFU on Linux

The DFU program used for Linux operating systems is ‘dfu-util’.

The procedure for Ubuntu Linux operating systems is described below.

To install this program, open a terminal and write the following command (with sudo to ensure having the correct

permissions):

sudo apt-get install dfu-util

Create a udev rules file:

sudo gedit /etc/udev/49-emotion.rules

and fill it with the following content:

# 0483:5740 - STM32F4 in USB Serial Mode (CN5) ATTRS{idVendor}=="0483", ATTRS{idProduct}=="5740",

ENV{ID_MM_DEVICE_IGNORE}="1"

ATTRS{idVendor}=="0483", ATTRS{idProduct}=="5740", ENV{MTP_NO_PROBE}="1"

SUBSYSTEMS=="usb", ATTRS{idVendor}=="0483", ATTRS{idProduct}=="5740", MODE:="0666"

KERNEL=="ttyACM*", ATTRS{idVendor}=="0483", ATTRS{idProduct}=="5740", MODE:="0666"

# 0483:df11 - STM32F4 in DFU mode (CN5) SUBSYSTEMS=="usb", ATTRS{idVendor}=="0483",

ATTRS{idProduct}=="df11", MODE:="0666"

Tell udev to reload its rules:

sudo udevadm control --reload-rules

You should now be able to program the board. So, connect the eMotion board in DFU mode, and run the following

command:

sudo dfu-util -a 0 -D dfu_path/file.dfu -d 0483:df11

where dfu_path and file.dfu are the path to the dfu file and the dfu file name respectively

(example: sudo dfu-util -a 0 -D Desktop/eMotionV2_REL_4_0.dfu -d 0483:df11).

To use the board with the upgraded firmware you need to disconnect and reconnect it, in order to exit DFU mode.

2.2.3 DFU on Mac OS

The DFU program used for Mac operating systems is ‘dfu-util’. Before installing it, you need to install Homebrew.

To do that, you need to open a terminal and run the following command:

ruby -e "$(curl -fsSL https://raw.github.com/Homebrew/homebrew/go/install)"

Once Homebrew is installed on your Mac, you can install dfu-utils with the following command:

brew install dfu-util

You should now be able to program the board. So, connect the eMotion board in DFU mode, and run the following

command:

dfu-util -a 0 -D dfu_path/file.dfu -d 0483:df11

where dfu_path and file.dfu are the path to the dfu file and the dfu file name respectively

(example: dfu-util -a 0 -D Desktop/eMotionV2_REL_4_0.dfu -d 0483:df11).

To use the board with the upgraded firmware you need to disconnect and reconnect it, in order to exit DFU mode.

UM0979

DFU

UM0979 - Rev 6 page 9/39

3 Supported MEMS adapter boards

Table 2. List of supported MEMS adapter boards below provides the complete list of supported adapter boards.

Table 2. List of supported MEMS adapter boards

Adapter board Device

STEVAL-MKI009V1 LIS3LV02DL

STEVAL-MKI013V1 LIS302DL

STEVAL-MKI015V1 LIS344ALH

STEVAL-MKI075V1 LY3100ALH

STEVAL-MKI084V1 LPY430AL

STEVAL-MKI087V1 LIS331DL

STEVAL-MKI089V1 LIS331DLH

STEVAL-MKI092V1 LIS331HH

STEVAL-MKI097V1 LPR430AL

STEVAL-MKI098V1 LPR410AL

STEVAL-MKI105V1 LIS3DH

STEVAL-MKI106V1 LSM303DLHC

STEVAL-MKI107V2 L3GD20

STEVAL-MKI108V2 9AXISMODULE v2 [LSM303DLHC + L3GD20]

STEVAL-MKI110V1 AIS328DQ

STEVAL-MKI113V1 LSM303DLM

STEVAL-MKI114V1 MAG PROBE (based on LSM303DLHC)

STEVAL-MKI120V1 LPS331AP

STEVAL-MKI122V1 LSM330DLC

STEVAL-MKI123V1 LSM330D

STEVAL-MKI124V1 10AXISMODULE [LSM303DLHC + L3GD20+ LPS331AP]

STEVAL-MKI125V1 A3G4250D

STEVAL-MKI133V1 LSM303D

STEVAL-MKI134V1 LIS3DSH

STEVAL-MKI135V1 LIS2DH

STEVAL-MKI136V1 L3GD20H

STEVAL-MKI137V1 LIS3MDL

STEVAL-MKI141V2 HTS221

STEVAL-MKI142V1 LPS25H

STEVAL-MKI151V1 LIS2DH12

STEVAL-MKI152V1 LIS2DM

STEVAL-MKI153V1 H3LIS331DL

STEVAL-MKI154V1 LSM9DS0

STEVAL-MKI158V1 AIS3624DQ

STEVAL-MKI159V1 LSM9DS1

UM0979

Supported MEMS adapter boards

UM0979 - Rev 6 page 10/39

Inhaltsverzeichnis

Andere STMicroelectronics Hauptplatine Handbücher

STMicroelectronics

STMicroelectronics STEVAL-ILL029V1 Bedienungsanleitung

STMicroelectronics

STMicroelectronics STM32F446RE Bedienungsanleitung

STMicroelectronics

STMicroelectronics STM32F4 Series Bedienungsanleitung

STMicroelectronics

STMicroelectronics STM32F756G-EVAL Bedienungsanleitung

STMicroelectronics

STMicroelectronics SPC570SADPT64S rev. B Bedienungsanleitung

STMicroelectronics

STMicroelectronics STEVAL-GLA001V1 Bedienungsanleitung

STMicroelectronics

STMicroelectronics STM32L152D-EVAL Bedienungsanleitung

STMicroelectronics

STMicroelectronics STSW-L9907-H Bedienungsanleitung

STMicroelectronics

STMicroelectronics STEVAL-IHM029V1 Bedienungsanleitung

STMicroelectronics

STMicroelectronics STM32F0 Series Bedienungsanleitung

STMicroelectronics

STMicroelectronics STR9 Series Bedienungsanleitung

STMicroelectronics

STMicroelectronics STEVAL-LLL002V1 Bedienungsanleitung

STMicroelectronics

STMicroelectronics LED7707 Montage- und Bedienungsanleitung

STMicroelectronics

STMicroelectronics STM32H7 Nucleo-144 Bedienungsanleitung

STMicroelectronics

STMicroelectronics SPC58NHADPT302S Bedienungsanleitung

STMicroelectronics

STMicroelectronics L62 Series Bedienungsanleitung

STMicroelectronics

STMicroelectronics STEVAL-ISQ006V1 Bedienungsanleitung

STMicroelectronics

STMicroelectronics STEVAL-3DP001V1 Administratorhandbuch

STMicroelectronics

STMicroelectronics AEK-POW-BMS63EN Bedienungsanleitung

STMicroelectronics

STMicroelectronics STM32F4 Series Bedienungsanleitung

STMicroelectronics

STMicroelectronics STEVAL-IME008V1 Bedienungsanleitung

STMicroelectronics

STMicroelectronics STM32100E-EVAL Bedienungsanleitung

STMicroelectronics

STMicroelectronics SPC570SADPT100S Bedienungsanleitung

STMicroelectronics

STMicroelectronics STM32L476G-EVAL Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung