Strong SRT 5400 Bedienungsanleitung
STRONG HD STB User’s Manual
IMPORTANT SAFETY INFORMATION
1
All safety and operating Instructions should be read before the product is operated.
All warnings on the product and in the operating instructions should be adhered to.
Do not use this apparatus near water.
Clean only with a dry cloth. Do not use liquid cleaners or aerosol cleaning products.
Do not block any of the ventilation openings.
Do not install near any heat sources.
Do not defeat the safety purpose of the polarized or grounding-type plug.
Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the apparatus.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel.
The SRT 5400 should be installed 10cm away from a wall to allow for the Power Switch and
Power Lead on the back panel
To reduce the risk of electric shock, do not remove cover (or back).
No user serviceable parts inside. Refer servicing to qualified
service personnel.
This symbol indicates dangerous voltage inside the product that
presents a risk of electric shock or personal injury.
This symbol indicates important instructions accompanying the
product.
STRONG HD STB User’s Manual
TABLE OF CONTENTS
2
1 Important Safety Information
2 Table of Contents
3 Introduction
4 Front Panel view
5 ~ 6 Rear Panel View
7 ~ 8 Remote Control Buttons
9 ~ 16 Installation
17 ~ 23 DTV Specific Menu Operations
24 ~ 30 Configuration Universal remote Control Unit
31 Menu Map
32 ~ 33 Technical Specifications
34 ~ 36 Rear Panel Connector Specifications
STRONG HD STB User’s Manual
INTRODUCTION
3
Thank you for purchasing this Strong Digital Terrestrial Television Receiver.
This product has been manufactured in accordance with strict Quality Control Procedures and is
fully compliant with Australian DVB-T digital television standards.
Your new Receiver will enable you to experience superior picture and sound quality, widescreen
images, extra channels plus a variety of new features.
UNIT CONTENTS
Remote control unit
Two batteries (size AA)
Video and stereo audio RCA cable
YPbPr(RGB color) cable
FEATURES
1080i / 720p / 576p / 576i Video Formats
Format Change by Remote Control
Simultaneous HD & SD
Component - YPbPr
DVI-I
RGBHV / RGB Component - VGA
Composite - CVBS
S-Video – Y/C
Dolby Digital Optical & Coaxial
16:9 Fullscreen, 4:3 Letterbox & Fullscreen
Picture in Picture
Zoom Mode by Remote Control Hot Key
Auto & Manual Channel Search
Favourite Channel List
Electronic Program Guide
Preprogrammed STB/TV Remote Control
Captions
Teletext
Super Sensitive Tuner
RS–232C Port for Software Upgrade
DVB/T Compliant, COFDM Demodulation
DVB, MPEG – 2 Compliant,
STRONG HD STB User’s Manual
FRONT PANEL VIEW
4
Standby LED : Standby mode LED
:Turn on/off power.
MENU : To access the main menu or to go back upper level.
GUIDE : To view program information
OK : Used to select item and complete numeric value entry or modify values in the menu
entry.
CH UP : Move cursor up from set up menu or channel up.
Digit LED display : This will display the current channel or certain programming functions
when using the menus.
CH DOWN : Move cursor down from set up menu or channel down.
IR : Infrared remote control sensor.
VOL UP : Volume ‘up’ adjustment
LAMP : Light on power on mode.
VOL DOWN : Volume ‘down’ adjustment
Front Panel buttons and menu allow for control of the SRT 5400 without the remote control unit
except the function of FAVORITES, INFO and some advanced features.
12
11
10
9
8
7
6
5
4
3
2
1
6 87 9 10
1211
12
1 2 3 4 5
STRONG HD STB User’s Manual
REAR PANEL VIEW
5
TV ANT IN : RF input for connecting the STB to a terrestrial antenna using a coaxial cable.
RF Out : To Connect to another set top box or recording device e. g. VCR / TV.
VIDEO (YELLOW) : Composite video jack for connecting the STB to your television using
standard RCA cable.
Variable Audio - L (WHITE) : Left RCA audio jack for connecting the STB to your television
audio input using standard RCA cable.
Variable Audio - R (RED) : Right RCA audio jack for connecting the STB to your television
audio input using standard RCA cable.
S/PDIF COAXIAL : Digital audio output for connecting the STB to your AV receiver or Dolby
Digital decoder using digital coaxial cable. Set this output to AC-3 Dolby
Digital or Stereo PCM in the STB setup menu or by the SAP button on
the remote control.
FIXED Audio - R (RED) : Right RCA audio jack for connecting the STB to your VCR audio
input using standard RCA cable.
FIXED Audio - L (WHITE) : Left RCA audio jack for connecting the STB to your VCR audio
input using standard RCA cable.
YPbPr OUT(Component) : Component RCA video jacks for connecting the STB to your
television using coaxial cables.
9
8
7
6
5
4
3
2
1
4 52 7 9
14131210
15
6 831 11
STRONG HD STB User’s Manual
6
VGA OUT : RGB/VGA component output for connecting the STB to a television using a
VGA cable.
S-VIDEO : S-video jacks for connecting the STB to an S-Video compatible VCR or
television.
S/PDIF OPTICAL : Digital audio output for connecting the STB to your AV receiver or Dolby
Digital decoder using optical cable. Set this output to AC-3 Dolby Digital
or Stereo PCM in the STB setup menu or by the SAP button on the
remote control
RS-232C : RS232C serial connection for future upgrades of the STB.
DVI-I OUT : Digital video signal and RGB component output for connecting the STB to a
television using a DVI cable.
NOTE : The YPbPr, VGA and DVI-I outputs carry the same R/G/B signals using
different physical connectors. Choose only one – do not use both at the same
time.
AC POWER INLET : Inlet to connect the STB to a standard power wall outlet.
15
14
13
12
11
10
STRONG HD STB User’s Manual
REMOTE CONTROL BUTTONS
7
12
4
6
7
8
9
14
16
12
20
22
25
26
29
30
34
36
38
18
3
5
13
15
19
17
21
23
28
27
31
33
35
32
37
POWER : Switch the STB between
operation and standby mode.
MUTE : Turns the audio on and off.
Line L, R output is not affected.
0 ~ 9 : Used to select channel
directly or set setup values like
password.
LOCK : Used to turn on/off –
Channel Lock.
+100 : Not Used
TV/VIDEO : Not Used
TV : Switch remote control unit to
television control mode.
dash button (-) : Not Used
STB : Switch remote control unit to
STB control mode.
WIDE : Aspect Ratio selection of
16:9 and 4:3
DISPLAY : Used to select
1080i/720p/576p/576i video mode
directly.
PICTURE : Zoom mode selection
including preview mode on picture
view (not for Composite or S-Video)
/ VOL + / VOL- : Used to volume
up and down.
/ CH +/CH- : Service up to down
through the available services.
1614
1513
12
11
10
9
8
7
6
5
4
3
2
1
11 10
24
STRONG HD STB User’s Manual
8
SUBTITLE : To turn Closed Captions on/off
SAP : Select Audio Program Dolby Digital and PCM
TELETEXT : Teletext
FAVORITES : Used to tune to next available Favorite program.
/ UP / DOWN : Move cursor up / down from set up menu.
/ LEFT/RIGHT : To navigate in program guide. Right button can be used as ENTER
button.
OK : To select item and complete numeric value entry or modify values in the menu entry.
MENU : Used to invoke set up menu or to go back upper level.
EXIT : To exit menu
! : To invoke Information Panel.
PIP : Turn on / off PIP function. (HD Outputs Only – not available when using S-Video and
CVBS Composite)
/ SUB +/- : Channel change for PIP
JUMP : Not used
PIP SWAP : Switch main program and sub program.
GUIDE : To view program guide.
SLEEP : Display the sleep time. At the sleep time, enter standby mode automatically.
BOOKMARK : Setting the Favorite channel
OPTION KEYS : Not used
REPEAT : Not used
38
37
36
35
33
32
31
3430
29
28
27
26
24
2322
2521
20
19
18
17
9
STRONG HD STB User’s Manual
INSTALLATION
A. Connector 9 : YPbPr (Component – For HD)
Using supplied Green / Blue / Red RCA Lead
CONNECTING THE SRT 5400 TO YOUR TELEVISION
For connection of the SRT 5400 there are number of alternatives depending what is your
preference and the connection types on your TV.
Please connect by either of the following methods:
A. B. C. For High Definition VIDEO Signal
D. E. For Standard Definition VIDEO Signal
F. Mandatory for Antenna connection
(Audio connections are explained separately following these video connection explanation
alternatives)
Refer to Page 5 & 6 for the Connector Reference Numbers listed below.
B. Connector 10 : VGA (For PC RGB signal- For HD)
You will need to purchase this lead separately.
Connector 9 YPbPr Connect to the Green/Blue/Red RCA
(Component)(
Component)Connectors of your TV
Connector 10 VGA Connect to the VGA connector of your TV
C. Connector 14: DVI-I (For HD)
You will need to purchase this lead separately
Connector 14 DVI Connect to the DVI connector of your TV
D. Connector 11: S-Video (Y/C) (For SD)
You will need to purchase this lead separately
Connector 11 S Video (Y/C) Connect to the S-Video connector of your TV
STRONG HD STB User’s Manual
10
E. CVBS (Composite – For SD) via the supplied Yellow / White / Red RCA Lead
For this Standard Definition Composite Video connection, Audio is also included, this will
be PCM Stereo.
F. Connecting the Antenna
Connect TV Antenna to Connector 1 (Aerial)
Audio Connections
PCM Stereo – Variable : Using supplied Yellow / White / Red RCA Lead
(Other than when connecting for CVBS Composite, the Yellow RCA will not be required to be
connected)
If you require Dolby Digital Audio Output (through you’re Dolby Digital Decoder Amplifier)
please refer to : DOLBY DIGITAL AUDIO (page 11)
Connector 3
(Yellow)
Connector 4
(White)
Connector 5
(Red)
VIDEO
AUDIO Left
AUDIO Right
RCA cinch
RCA cinch
RCA cinch
Connect to Video (Yellow) RCA
of your TV
Connect to audio (White) RCA
of your TV
Connect to audio (Red) RCA of
your TV
Connector 4
(White)
Connector 5
(Red)
AUDIO Left
AUDIO Right
RCA cinch
RCA cinch
Connect to audio RCA input
(White) of your TV
Connect to audio RCA input
(Red) of your TV
Connector 7
(Red)
Connector 8
(White)
AUDIO Right
AUDIO Left
RCA cinch
RCA cinch
Connect to audio RCA input
(White) of your TV
Connect to audio RCA input
(Red) of your TV
PCM Stereo – Fixed Using supplied Yellow / White / Red RCA Lead
Refer Page 22: 2nd Audio Volume Mode
(Other than when connecting for CVBS Composite, the Yellow RCA will not be required to be
connected)
Connector 1 Aerial IEC169-2
female
Input from Antenna to Receiver
Inhaltsverzeichnis
Andere Strong Fernsehempfänger Handbücher
Strong
Strong SRT 5001 Bedienungsanleitung
Strong
Strong SRT 5024 Bedienungsanleitung
Strong
Strong SRT 8109 Bedienungsanleitung
Strong
Strong SRT 5425 Bedienungsanleitung
Strong
Strong SRT 2401 Betriebsanleitung
Strong
Strong SRT 7004 Bedienungsanleitung
Strong
Strong SRT 6010 Bedienungsanleitung
Strong
Strong SRT 5505 MHP Bedienungsanleitung
Strong
Strong SRT 8345 CI Bedienungsanleitung
Strong
Strong SRT 80 Bedienungsanleitung
Strong
Strong SRT 8119 Bedienungsanleitung
Strong
Strong PRIMA VI Bedienungsanleitung
Strong
Strong SRT 5855 Bedienungsanleitung
Strong
Strong SRT 5405 Bedienungsanleitung
Strong
Strong SRT 8202 Bedienungsanleitung
Strong
Strong SRT 8113 Bedienungsanleitung
Strong
Strong PRIMA IV Bedienungsanleitung
Strong
Strong SRT8500 Bedienungsanleitung
Strong
Strong SRT 5011 Bedienungsanleitung
Strong
Strong SRT5431 Bedienungsanleitung
