Stryker Quantum 2000 Bedienungsanleitung

Quantum 2000 Light Source

Model Number: Q2000

Operating Manual

VERSION PAGE

English

Nederlander 13

Fraqais

Deutsch

Italian0 55

Espagiiol 69

Light Source Menu

Service Manual

CONTENTS

Thank you for purchasing the Stryker Quantum 2000 Light Source, designed

by a leading worldwide manufacturer of illuminated diagnostic instruments. By

following the use and care guidelines given in this manual, you will be reward-

ed with years of dependable, trouble-free service from your new Light Source.

Read these instructions thoroughly before use.

System

Symbol

Descriptions..

....................... 1

Warnings and

Precautions..

............................ 2

System Description..

........................................

System

Set-up/Operation ................................ 5

Lamp Replacement .......................................... 6

Fuse Replacement .......................................... 8

Cleaning ............................................................ 9

Specifications

.................................................. 10

Troubleshooting Guide..

..................................

1 1

Maintenance and Repair.. ................................ 12

Warranty and Service ...................................... 12

Ordering Information ...................................... 12

REF

CAUTION

Catalog Number

Attention: Read operating manual for warnings, precautions,

and instructions for use.

Dangerous Voltage: Refer servicing to qualified personnel.

Type B Equipment

Caution

Hot

Warning: Risk of fire. replace fuses as marked.

Light; Lighting; Illumination Intensity

Conformance to:

93/42/EEC

Medical Device Directive

Serial Number

INDICATIONS

Use of the Quantum 2000 Light Source is indicated for medical lighting

applications requiring a remotely located, high-quality white light.

This product must only be used by qualified medical personnel.

CONTRAINDICATIONS

The use of the Quantum 2000 Light Source is contraindicated for applica-

tions where high intensity light might burn or damage tissue; such as

for neonate transillumination and ophthalmic procedures. For further

contraindications, the user must also consult the operating manual of

the instrument being used with the Light Source in the medical procedure.

WARNINGS AND PRECAUTIONS

SYSTEM DESCRIPTION

The Quantum 2000 Light Source is used to supply high-quality, white light

for video and optical illumination systems. It accepts standard

ACMI

connectors.

PowerSwitch

Minimum

Light Output

Maximum

Light Output

Fiber Optic

Bundle Port

Control Knob

FRONT

AC Power Outlet

Fuse

Draw

Fan Grill

BACK

Lamp Access

Door

SET-UP AND OPERATION

After a 15-second warm-up period, the light output will stabilize at its

normal intensity.

Plug the Quantum 2000 Light Source into a hospital-grade receptacle.

2. Turn the light-intensity control knob to its minimum position. Plug the fiber

optic bundle into the illuminator port and connect the opposite end to the

instrument.

3. Turn the power switch to the on position. The lamp will take 15 seconds to

complete its warm-up cycle.

4. Set light intensity to desired level.

5. Turn unit off when not in use.

NOTE: Do not restart lamp immediately after turning off.The lamp

may fail to start. If this occurs, turn the power switch off and wait

15 seconds before restarting the Quantum 2000 Light Source.

Turn unit off and unplug the power cord from both the wall outlet and the

Quantum 2000 Light Source.

2. Remove the lamp access door from the bottom of the Quantum 2000

Light Source by loosening the thumbscrew and gently lifting the door

open. Leaving the wires attached, gently lay door aside to gain access

to the lamp.

3. Disconnect the lamp connector

assembly by pulling back on the

black connector.

-1

Black Connector

4. Remove the lamp from the holding

spring assembly by firmly grasping

the ceramic lamp base and pulling

the lamp gently toward the rear.

While pulling back, slide the lamp

up and over the tension spring and

out of the light source.

Ceramic Lamp Base

Tension

Springs

NOTE: Replace with Stryker lamp #502 220 176 only. Do not touch the

lamp itself, or the interior reflective surface of the lamp. Skin oils on the

lamp will cause premature lamp failure. Always hold lamp by the ceramic

connector base. Remove any grease or fingerprints with a clean cotton

swab moistened with alcohol. Do not leave any lint on the lamp.

5. To install a new lamp, grasp the lamp by the ceramic base and be

sure that the alignment pin on the lamp is pointing up. Gently slide the

lamp down into place between the holding spring assembly and the front

of the box, allowing the holding spring to help seat the lamp in the fixture.

Check to be sure that the

alignment pin on the lamp is

securely placed in the slot on

the fixture. When the lamp is

properly seated, you will be

able to rotate the lamp slight-

ly in either direction. If lamp

does not rotate at all, or

rotates freely, pull back gen-

tly and reposition lamp as

described above. Plug the

black connector assembly

wire back into the lamp.

---A-)-1

assembly

Be sure

alignment pin

and lamp are

properly seated

black connector

‘wire

6. Reattach the lamp door securely. The unit will not power up unless the

lamp door is seated properly.

FUSE REPLACEMENT

Turn the unit off and remove the power cord from both the wall outlet and

the Quantum 2000 Light Source.

Fuse Holder

2. Use a small screwdriver to remove the fuse holder below the power cord

connector by releasing the spring-loaded snap connections.

3. Pull out the fuse holder.

4. Remove and replace with new fuses of the same type. There is no

required orientation of the fuses. Be sure to replace both fuses.

5. Reinsert the fuse holder by pressing it into the power connector until it

snaps into place.

6. If the new fuse blows, immediately contact Stryker Technical Service.

Fuses

Snap

Connections

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Stryker Medizinische Geräte Handbücher

Stryker

Stryker Gynnie Bedienungsanleitung

Stryker

Stryker Gynnie 1061 Bedienungsanleitung

Stryker

Stryker Secure 3000 Bedienungsanleitung

Stryker

Stryker 6370 Bedienungsanleitung

Stryker

Stryker 1115 Bedienungsanleitung

Stryker

Stryker System 6 6203-000-000 Bedienungsanleitung

Stryker

Stryker System 6 6205-000-000 Bedienungsanleitung

Stryker

Stryker S3 MEDSURG BED Bedienungsanleitung

Stryker

Stryker Triathlon Bedienungsanleitung

Stryker

Stryker 1000 Bedienungsanleitung

Stryker

Stryker MX-PRO R3 6082 Bedienungsanleitung

Stryker

Stryker Power-LOAD Benutzerhandbuch

Stryker

Stryker IsoFlex SE Bedienungsanleitung

Stryker

Stryker 240-099-156 Bedienungsanleitung

Stryker

Stryker Neptune 2 Rover-ULTRA Bedienungsanleitung

Stryker

Stryker 1069 Bedienungsanleitung

Stryker

Stryker Berchtold CHROMOPHARE Bauanleitung

Stryker

Stryker 1004 Bedienungsanleitung

Stryker

Stryker CastVac 0986-000-000 Bedienungsanleitung

Stryker

Stryker EPIC II 2031 Bedienungsanleitung

Stryker

Stryker 1288 Bedienungsanleitung

Stryker

Stryker Flosteady Arthroscopy Pump 200 Bedienungsanleitung

Stryker

Stryker LF2019 Bedienungsanleitung

Stryker

Stryker Gynnie 1061 Bedienungsanleitung

Beliebte Medizinische Geräte Handbücher anderer Marken

TekTone

TekTone Tek-CARE160 Bedienungsanleitung

NeuroMetrix

NeuroMetrix Quell 2.0 Bedienungsanleitung

AMT

AMT XLR8 Bedienungsanleitung

EDAN

EDAN SONOTRAX Pro Bedienungsanleitung

Restorative Therapies

Restorative Therapies RT300 Bedienungsanleitung

Gendex

Gendex Expert DC Bedienungsanleitung

Dexcowin

Dexcowin ADX4000W Bedienungsanleitung

Libelium

Libelium MySignals Bedienungsanleitung

Acelity

Acelity V.A.C.ULTA 4 Bedienungsanleitung

Caputron

Caputron ActivaDose II tDCS Bedienungsanleitung

Plinth 2000

Plinth 2000 93CDT Bedienungsanleitung

GE SENOGRAPHE 800T Bedienungsanleitung

GE Definium 5000 Bedienungsanleitung

Kanmed

Kanmed GE-1380 Bedienungsanleitung

Huntleigh

Huntleigh FD1 Bedienungsanleitung

Tobii Dynavox

Tobii Dynavox I-Series Bedienungsanleitung

S-Capepod

S-Capepod Evac Cocoon Bedienungsanleitung

Romet

Romet R210 Bedienungsanleitung