Sub-Zero 200 Series Bedienungsanleitung

200

INSTALLATION GUIDE

200

SERIES

200 IG 3758400 1-04.qxd 1/2/2004 7:55 AM Page 1

INSTALLATION GUIDE

200

SERIES

200 IG 3758400 1-04.qxd 1/2/2004 7:55 AM Page 2

Before you begin your installation of a Sub-Zero 200 Series

unit, there are a few things you should take special care to

observe. By reading these introductory instructions careful-

ly, you will make the installation procedure easier, problem-

free and, most important, safe.

First, as you follow these installation instructions, take par-

ticular note of the WARNING! and CAUTION! symbols

when they appear. This information is important for the safe

and efficient installation of this Sub-Zero.

Also, The printed instructions may signal an IMPORTANT

NOTE, which highlights information that is especially

important for a problem-free installation.

Second, make sure that the actual equipment that was

shipped to you matches the design you are expecting to

install. Sub-Zero 200 Series offers models 249R, 249RP,

249FF and 245.

Each of these design options has specific installation

requirements, which means it is vital that the unit match

your planning and space needs. Before you begin, check the

exact model number you need against the model numbers

on the shipping carton.

If the unit you receive does not match your requirements,

contact your Sub-Zero dealer.

WARNING

alerts you to a hazard that may cause serious injury or

death if precautions are not followed.

CAUTION

signals a hazard where minor injury or product damage

may occur if you do not follow instructions.

200

SERIES

INSTALLATION GUIDE

200 IG 3758400 1-04.qxd 1/2/2004 7:55 AM Page 3

PREPARING THE SPACE

Step 1: First, make sure that the opening where the

Sub-Zero is to be installed is properly prepared. Refer to the

Pre-Installation Specifications illustrations and chart to be

sure the space dimensions, electrical service and plumbing

are correct for the model you are about to install.

IMPORTANT NOTE: To operate properly, the door must

open a minimum of 90°. Use a minimum 2" (51 mm) filler

in corner installations to assure a 90° door opening. Allow

enough clearance in front of the unit for full door swing.

IMPORTANT NOTE: Make sure the floor under the refrig-

erator is level with the surrounding finished floor. Protect a

finished floor with plywood, cardboard or some other suit-

able material before moving the refrigerator across it.

200

SERIES

PRE-INSTALLATION SPECIFICATIONS

MODELS 249R, 249R, 249FF AND 245

ROUGH-IN REQUIREMENTS

200 IG 3758400 1-04.qxd 1/2/2004 7:55 AM Page 4

Finished Rough Finished Rough

Opening Width (A) Opening Height (B)

Model 249R 24"(610) 34 1/2"(876)

Model 249RP 24"(610) 34 1/2"(876)

Model 249FF 24"(610) 34 1/2"(876)

Model 245 24"(610) 34 1/2"(876)

NOTE: Dimensions in parentheses are in millimeters.

Refer to illustration on page 4.

200

SERIES

PRE-INSTALLATION SPECIFICATIONS

Recommended Electrical Recommended Electrical

Width Location (C) Opening Height (D)

Model 249R 12"(305) 14"(356)

Model 249RP 12"(305) 14"(356)

Model 249FF 5"(127) 14"(356)

Model 245 5 1/2"(140) 4 1/2"(114)

NOTE: Dimensions in parentheses are in millimeters.

Refer to illustration on page 4.

Door Panel

Dimensions

(Width x Height)

Model 249R 23 5/8" x 30"(600 x 762)

Model 249RP 23 5/8" x 30"(600 x 762)

Model 249FF 23 5/8" x 30"(600 x 762)

Model 245 23 1/2" x 28 1/8”"(597 x 714)

NOTE: Dimensions in parentheses are in millimeters.

Refer to illustration on page 4.

200 IG 3758400 1-04.qxd 1/2/2004 7:55 AM Page 5

PREPARING ELECTRICAL

CONNECTIONS

Step 3: To prepare the electrical system, rough in the elec-

trical outlet following the Pre-Installation Specifications.

You will need a 115 volt, 60 Hertz electrical supply. Dedicate

a separate 15 amp fuse or circuit breaker to the Sub-Zero

unit, and follow any local codes that apply.

The Sub-Zero unit comes with a power supply cord with a

three-prong grounding plug. The refrigerator must be

plugged into a mating three-prong wall receptacle ground-

ed in accordance with the National Electrical Code and local

codes.

PREPARING PLUMBING

CONNECTIONS

Step 4: For units with automatic ice makers, first rough in

the water supply line. Connect a 1/4" copper line to the

house supply. Use an easily accessible shut-off valve

between the supply and the refrigerator. This is usually

about 6" (152 mm) from the compression fitting. The ice

maker operates on water pressure of 20 psi (1.4 bar) to 100

psi (6.9 bar). But don’t use a self-piercing valve. See your

Sub-Zero dealer for a saddle valve kit, ask for part number

4200880.

NOTE: Dimensions in parentheses are in millimeters.

If the local water supply has high levels of sediment, con-

sider adding an in-line filter.

Good water is important for good ice quality. It is not rec-

ommended that the ice maker be connected to a softened

water supply. Water softener chemicals, such as salt from a

malfunctioning softener, can damage the ice maker mold

and lead to poor ice quality. If a softened water supply can-

not be avoided, it is important that the water softener be

well maintained and operating properly.

Reverse osmosis systems can be used, provided there is a

consistent water pressure of 20 psi (1.4 bar) to 100 psi (6.9

bar) supplied to the water valve at all times.

Route the water line through the floor within 1/2" (13 mm)

from the wall and no higher than 3" (76 mm) from the

floor. If the water supply is brought in from behind the unit,

route the water line through the wall no more than 3" (76

mm) from the floor. In either case, allow at least 3' (1 m) of

excess copper tubing outside the wall or floor for easy con-

nection to the refrigerator.

WARNING

Do not use an extension cord, or two prong adapter.

Electrical ground is required on this appliance.

Do not under any circumstances remove the power sup-

ply cord ground prong.

200

SERIES

INSTALLATION

200 IG 3758400 1-04.qxd 1/2/2004 7:55 AM Page 6

UNPACKING THE SUB-ZERO

Step 5: Unpack the unit, remove the unit shipping carton.

Remove the wood base by extracting all 4 levelers and then

discard the wood base. Reinstall all 4 levelers back into the

unit base assembly. Remove all packing materials and tape

as well. Do not discard the kickplate. Next, prelevel the unit

by adjusting the leveler legs prior to pushing unit back into

the installation.

200

SERIES

ICEMAKER OPERATION:

After the water has been hooked up to the icemaker, lower

stop arm of icemaker.

NOTE: You will need to allow some time for product to cool

down sufficiently enough to produce ice. When the arm is

down, it signals the icemaker that the ice supply is low and the

icemaker automatically starts and replenishes the ice bucket.

It will shut off automatically when the bucket is filled.The first

time the icemaker operates, allow a few days for the bucket to

fill. You might notice the first few crescents of ice are discol-

ored.This is probably due to the new plumbing connection,

and you should discard the first 3 dumps of ice. Ice, if kept

over a period of time will stick together and crescents will

shrink. To avoid this, empty the ice bucket at least once a

month. (See Illustration 1.)

WARNING

Keep door(s) and drawer(s) taped closed while moving

unit.

Illus. 1

200 IG 3758400 1-04.qxd 1/2/2004 7:55 AM Page 7

Step 9: Now, level the unit. Adjust both the front and rear

levelers by turning the levelers clockwise - to raise the unit,

counterclockwise - to lower the unit. When the unit is lev-

eled properly, or squared off, door adjustments are less like-

ly to be necessary. (See Figure 3.)

IMPORTANT NOTE: Be sure to reference leveling of the

unit to the floor and not to surrounding cabinetry. This could

effect the operation of the unit, such as door(s) not closing

properly.

Step 10: After the unit has been leveled, install the kick-

plate as shown in illustration 2.

COMPLETING THE INSTALLATION

Step 8: To complete the installation, first shut off power

to the wall outlet. Plug into a 15 amp grounded outlet

and roll the unit into position. Now you have to connect the

ice maker water line (if applicable). Remove the 1/4" com-

pression fitting from its plastic bag and join the water sup-

ply line to the solenoid valve.

IMPORTANT NOTE: Make sure to purge the water

line prior to hooking up the water valve.

IMPORTANT NOTE: Turn on the water supply and

check all fittings for leaks. Make certain the electrical

harness is attached to the solenoid.

In areas with water of high mineral content, the use of an

in-line water filter is recommended. Make sure the filter is

positioned and accessible for replacement when necessary.

IMPORTANT NOTE: Let your customer know that the

ice maker will not fill with water immediately, and

that the first three batches of ice produced should be

discarded. Allow 24 hours to get proper ice production.

CAUTION

Protect any finished flooring before moving the unit in

place. If for any reason the unit has been laid on its

back or side, for over a hour, you must allow the unit

to stand upright for a minimum of 24 hours before con-

necting power.

200

SERIES

Illus. 2

CAUTION

Do not block the kickplate louvers with carpeting, base-

board or other materials. This will cause poor operation

or product failure.

200 IG 3758400 1-04.qxd 1/2/2004 7:55 AM Page 8

All Sub-Zero undercounter units are manufactured in a

manner to achieve a total built-in appearance.This allows

you to choose the decorative material and color application

for the front of your refrigerator/freezer. To install front

panel on all Sub-Zero undercounter models:

1)Remove door handle. Handle is located on the top on the

245 model, and on the side on other models. Handle is held

on with phillips head screws. (See illustrations 3 and 4.)

2) Slide 1/4 (6) thick panel into frame on door. Door must be

opened 90° on 245 models.If a thinner panel is used, install

chipboard filler panels behind the trim panel for proper fit.

IMPORTANT: Routing may be required on some raised

panels for finger clearance under handle.

3) With panel in position, replace handle. Replace and tight-

en all screws. Do not overtighten and “strip”screws. Refer

to pages 4 & 5 for installation dimensions. NOTE: 20# per

door panel maximum weight limit.

INSTALLING PANELS

Before you begin installing panels, refer to the Panel

Specifications Dimensions on page 5, and be sure you are

working with the Sub-Zero panel design called for in your

installation plans. No panels or handle hardware are nec-

essary to install.

ACCOMMODATIONS FOR RAISED

PANELS

You may have to rout, recess some door panel designs to

allow for finger clearance. This is particularly true if your

unit has raised panels greater than 1/4"(6) total thickness.

Check the location of offset when you’re using specific rout-

ing for the grip area only. Refer to the 200 Series section of

the Sub-Zero Design Guide for additional information.

NOTE: Dimensions in parentheses are in millimeters.

200

SERIES

Illus. 3

Illus. 4

200 IG 3758400 1-04.qxd 1/2/2004 7:55 AM Page 9

1010101010

DOOR SWING CHANGE

Model 245: Upper; interchange hinge, screws and corner

cap with hole plugs and corner cap on opposite side of cab-

inet and door. Lower; interchange hinge and screws with

hole plugs on opposite side of cabinet. Move closer cam,

screw and cam support plate to opposite side of door.

(See Illustrations 6 & 7.)

ADJUSTING THE HINGES

It is possible that doors may come out of adjustment If

doors need adjustment, please refer to the follwoing door

adjustment directions.

Model 249 Series: Top and bottom hinges can be adjust-

ed left to right and in & out, by loosening the two Phillips

head screws. Model 245: Hinges are factory set; no field

adjustment provided for. (See Illustration 5). Model 249

Series: Can be ordered either as a right-hand or left-hand

product. Contact Sub-Zero dealer if swing change kit is

required.

200

SERIES

Illus. 5

Illus. 7

Illus. 6

200 IG 3758400 1-04.qxd 1/2/2004 7:55 AM Page 10

Andere Handbücher für 200 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sub-Zero Kühlschrank Handbücher

Sub-Zero

Sub-Zero Designer Series Bedienungsanleitung

Sub-Zero

Sub-Zero BI-36R Montageanleitung

Sub-Zero

Sub-Zero BI-36RG Montageanleitung

Sub-Zero

Sub-Zero Designer Series Bedienungsanleitung

Sub-Zero

Sub-Zero 600 Series BI-36S Bedienungsanleitung

Sub-Zero

Sub-Zero 600 Series BI-30U Bedienungsanleitung

Sub-Zero

Sub-Zero 500 Series Bedienungsanleitung

Sub-Zero

Sub-Zero BI-36U/S/TH Bedienungsanleitung

Sub-Zero

Sub-Zero 700-2 Series Bedienungsanleitung

Sub-Zero

Sub-Zero 661 Bedienungsanleitung

Sub-Zero

Sub-Zero 601R Betriebsanleitung

Sub-Zero

Sub-Zero 648PRO Bedienungsanleitung

Sub-Zero

Sub-Zero 642 Gebrauchsanweisung

Sub-Zero

Sub-Zero BI-42SID Bedienungsanleitung

Sub-Zero

Sub-Zero IT36RRH Bedienungsanleitung

Sub-Zero

Sub-Zero Sub-Zero 648PROG Bedienungsanleitung

Sub-Zero

Sub-Zero IC-24FI Bedienungsanleitung

Sub-Zero

Sub-Zero 600 Series BI-36S Bedienungsanleitung

Sub-Zero

Sub-Zero ICBBI-36R Bedienungsanleitung

Sub-Zero

Sub-Zero Undercounter Refrigeration Betriebsanleitung

Sub-Zero

Sub-Zero 600 Series BI-36UG Bedienungsanleitung

Sub-Zero

Sub-Zero ID-30RP Bedienungsanleitung

Sub-Zero

Sub-Zero BI-30U Montageanleitung

Sub-Zero

Sub-Zero ICB648PRO Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung