Summit FF591OS Bedienungsanleitung

BUILT-IN OUTDOOR REFRIGERATOR

Model FF591OS

User’s Manual

BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES

AND OPERATING INSTRUCTIONS.

Write Serial Number here:

______________________________

FELIX STORCH, INC.

Summit Appliance Division

An ISO 9001:2015 registered company

770 Garrison Avenue

Bronx, New York 10474

www.summitappliance.com

TABLE OF CONTENTS

Unpacking the Refrigerator ........................................................................................2

Important Safety Instructions ......................................................................................2

Electrical Requirements .............................................................................................3

Placing Your Refrigerator ...........................................................................................3

Refrigerator Features ...........................................................................................4 –5

Temperature Control Knob ..............................................................................4

Adjusting the Control Knob ..............................................................................4

Refrigerator Shelves ........................................................................................4

Adjusting the Refrigerator Tilt ....................................................................4 –5

Refrigerator Sounds ........................................................................................5

Refrigerator Care ..................................................................................................6 –9

Cleaning Your Refrigerator ..............................................................................6

Replacing the Light Bulb ..................................................................................6

Vacations .........................................................................................................7

Moving Care ....................................................................................................7

Reversing the Door Hinge .........................................................................7 –8

Replacing / Removing the Base Grille .............................................................9

Disposing of a Worn-Out Appliance ...........................................................................9

Troubleshooting .......................................................................................................10

Limited Warranty ......................................................................................................11

UNPACKING THE REFRIGERATOR

Remove tape, and clean off any residual glue from the refrigerator surfaces before

turning the unit on. Apply a drop of liquid dish detergent over the residue with your

fingers, wipe down using warm water and dry.

In order to prevent damage to the surface of your refrigerator, do not use rubbing alcohol,

flammable fluids, abrasive cleaners or sharp tools when removing the packing tape and

glue.

Discard or recycle all packaging material.

Clean the inside of your refrigerator prior to operation. Refer to the “Cleaning Your

Refrigerator” on page 6.

IMPORTANT SAFETY INSTRUCTIONS

The safety of you and others around you is very important.

Safety messages should be read completely and followed at all times.

This is the safety alert symbol.

It indicates potential hazards that can kill or hurt you and others.

Messages about safety will tell you what the potential hazard is, how to reduce

the chance of injury, and what can happen if the instructions are not followed.

WARNING:

To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these

basic precautions:

Plug into a grounded 3-prong outlet.

Do not remove the ground prong.

Do not use an adapter.

Do not use an extension cord.

Disconnect power before servicing.

Use nonflammable product when cleaning the refrigerator.

Keep flammable materials, such as gasoline, away from the refrigerator.

Use two or more people to move and/or install the refrigerator.

Proper disposal of old appliances:

DANGER! Old appliances can represent a suffocation hazard to children.

Remove doors from your old appliance.

Leave shelves in place.

If old appliance contains refrigerants, it must be recycled by a licensed service or

disposal company.

–SAVE THESE INSTRUCTIONS –

ELECTRICAL REQUIREMENTS

Before moving your refrigerator to its desired location, it is important to check that the proper

electrical connection will be used.

Recommended grounding method

A 115 Volt, 60 Hz., AC only, 15- or 20-amp fused, grounded electrical supply is required.

It is recommended that a separate circuit serving only your refrigerator be provided. Use an

outlet that cannot be turned off by a switch. Do not use an extension cord.

NOTE: Be sure to unplug the refrigerator prior to installation, cleaning, or general maintenance

such as changing the light bulb.

PLACING YOUR REFRIGERATOR

WARNING:

Two or more people are required to move and/or install the refrigerator. Failure to do

so may cause back or other injury.

NOTE: The letters “OS” in the model number of your appliance indicate that it can be used in

outdoor settings. It has special insulation and a weather-resistant stainless steel body wrap.

Also, a GFCI (Ground Fault Circuit Interrupter) is built into the line cord. In the event the

refrigerator is not operating, first check to see that the GFCI has not tripped, then press the

RESET button.

1. Choose a location for the refrigerator that has a strong, level floor. If such a place is

unavailable, be sure to adjust the rotating leg supports such that the refrigerator is always

kept level.

2. Your refrigerator needs at least ¼” (6.35 mm) of air space at the top and on the sides, and

2” (5.08 cm) at the rear to allow for proper air ventilation. Be sure that airflow under the

appliance is not blocked. If the refrigerator is installed next to a fixed wall, provide at least

2½ inches (6.35 cm) of room on the hinge side to allow for the door to swing open.

3. Avoid direct sunlight and heat. Light will discolor the enamel finish. In addition, when placed

near a heat source such as stove or direct sunlight, the refrigerator will consume more

electricity. Similarly, avoid installing in relatively cold locations: do not install in a place

where the temperature will fall below 55°F (13°C).

4. Avoid moisture. If placed near a sink or water faucet, the evaporator will frost faster because

of the higher humidity.

WARNING:

EXPLOSION HAZARD. Keep flammable materials and vapors, such as gasoline, away

from the refrigerator. Failure to do so can result in death, explosion or fire.

REFRIGERATOR FEATURES

Temperature Control Knob

The refrigerator’s temperature control knob is preset at the factory for

your convenience. When first installing your refrigerator, be sure that

the control is still in the mid-point setting as shown.

Adjusting the Control Knob

The mid-setting indicated in the section above should be ideal for regular use.

However, if you need to adjust the temperature, be sure to wait at least 24 hours between

adjustments. Check the temperature, and adjust the knob to the next higher setting to make

the refrigerator colder. To make the refrigerator less cold, adjust the control to the next lower

setting.

Refrigerator Shelves

You can remove the shelf by lifting up the front and pulling it out of the shelf slot.

You can replace the shelf by inserting it into the shelf slot and pushing it toward the back

of the compartment.

NOTE: Keep similar foods together on the same shelf. This helps to reduce the time the

refrigerator door is open and therefore save energy.

Adjusting the Refrigerator Tilt

If your refrigerator seems unsteady or you would like the door to close more easily, you

can use the four refrigerator leveling legs to adjust the tilt of the unit.

Be sure that the refrigerator is in its final position when making adjustments to the tilt,

and that it is plugged into a grounded 3 prong outlet.

WARNING:

Two or more people are required to move and/or install the refrigerator. Failure to

do so may cause back or other injury.

Important Information Regarding Glass Shelves:

Never clean the glass shelves with warm water when they are cold. The glass

may break if exposed to sudden temperature changes or impact, such as

bumping.

The refrigerator’s shelves use tempered glass, which is designed to shatter into

many small, pebble-size pieces. This is normal.

Glass shelves are heavy. Use both hands when removing them to avoid

dropping.

WARNING:

Plug into a grounded 3-prong outlet.

Do not remove ground prong.

Do not use an adaptor.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire or electrical shock.

Turning a leveling leg to the right will lower the refrigerator toward the position of the leg.

Likewise, turning to the left will raise the unit away from the leg.

Several turns of the leveling legs may be required before the refrigerator tilt is properly

adjusted.

Turning both front legs the same amount to the left will tilt the refrigerator to the rear. This

adjustment makes it easier for the door to close.

NOTE: It is easier to adjust the leveling legs if someone else pushes against the top of

the refrigerator to take the weight off the legs.

Refrigerator Sounds

After your new refrigerator has run for a while, you may notice some sounds being generated by

the unit. These are normal. Any hard surfaces surrounding the unit, such as the floor or

cabinetry, can make the sounds seem louder. The following list explains some of the sounds

you may hear, and their causes.

Your refrigerator uses a high efficiency compressor and fans to keep your food items at

the desired temperature while minimizing energy usage. The fan and compressor may

therefore run for longer periods than your old refrigerator. You may also notice a pulsating

or high-pitched sound coming from the compressor or fans, as they adjust to optimize

performance.

As refrigerant flows inside the cabinet, you may hear some rattling noises. This may also

be caused by items stored inside the cabinet.

After each cooling cycle, you might hear a gurgling sound caused by the refrigerant

flowing in your refrigerator.

When the refrigerator is defrosting, you might hear water running into the drain pan.

Each time the refrigerator starts or stops running, you may hear some clicking sounds.

Leveling leg

REFRIGERATOR CARE

Cleaning Your Refrigerator

NOTE: To prevent the buildup of odors, clean the refrigerator about once a month. Follow the

below procedures for cleaning:

1. Disconnect from power.

2. Remove parts such as shelves, etc. that can be taken out of the refrigerator.

3. Using a clean sponge or soft cloth, hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a mild detergent in warm water. DO NOT use abrasive or harsh

cleaners such as window sprays, scouring cleansers, flammable fluids, cleaning waxes,

concentrated detergents, bleaches or cleansers containing petroleum products. DO NOT

use harsh cleaning tools such as paper towels or scouring pads, as these can scratch or

damage the surfaces of the refrigerator.

4. For stainless steel and painted metal exterior surfaces, use a clean sponge or soft cloth

and a mild detergent in warm water. DO NOT use abrasive or harsh cleaners, or cleaners

containing chlorine, as these can scratch or damage the material. Using a soft cloth, dry

thoroughly.

5. To help with removing odors, you can use a mixture of warm water and baking soda (2 tbs

to 1 qt of water) to wash the interior walls.

6. After cleaning, replace all of the parts that were removed from refrigerator.

7. The condenser coils, located behind the base grille, should also be cleaned regularly. This

may be as often as every other month. Cleaning the condenser coils may help reduce

how much energy the refrigerator uses.

Remove the base grille (see “Removing / Replacing the Base Grill” section on page 9).

When the condenser coils are dusty or dirty, use a vacuum cleaner with an extension

attachment.

Replace the base grille.

8. After cleaning the refrigerator, plug in or reconnect power.

Replacing the Light Bulb

NOTE: The bulb should be exchanged with one of the same size, shape, and wattage, as not all

appliance bulbs are suited for your refrigerator.

1. Disconnect from power.

2. Remove the screw located at the back of the light shield with a Phillips screwdriver. By

pulling the light shield back, remove the tabs attached to the refrigerator, and detach the

light shield.

3. Replace the bulb.

4. To reattach the light shield, push the tabs back in. Align the holes and insert the screw,

tightening as needed.

5. Connect to power.

Vacations

Use up any perishable goods and freeze other items if you choose to leave the refrigerator on

while you are away.

If the refrigerator will be turned off prior to your departure, follow these steps.

1. Remove all food from the refrigerator.

2. Unplug the refrigerator.

3. Clean the refrigerator. See “Cleaning Your Refrigerator” on page 6.

4. Prop the door open so that sufficient air can enter the refrigerator. Do so by taping a

rubber or wood block to the top of the door. Allowing air to flow into the refrigerator

prevents the buildup of odor and mold.

Moving Care

Follow the instructions below to prepare your refrigerator when moving to a new location, such

as a new home.

1. Remove all products from the refrigerator.

2. Unplug the refrigerator.

3. Clean, wipe, and dry the unit completely.

4. Take out all removable parts, wrap them, and tape them together securely so they don’t

shift and rattle during the move.

5. Tape the doors shut and tape the power cord to the rear of the refrigerator.

WARNING:

Two or more people are required to move and/or install the refrigerator. Failure to do so

may cause back or other injury.

Reversing the Door Hinge (optional)

Required Tools: Phillips screwdriver

1. Disconnect power from the unit.

2. Remove each of the screws on the top of the unit. There should be a total of seven (3 on

the hinge side, 4 on the unhinged side). Be careful not to lose or discard the screws.

3. Remove the TOP HINGE and WASHER (see picture on next page) and set aside.

4. Lift the door straight up and off of the BOTTOM HINGE.

5. Remove the screws fastening the BOTTOM HINGE and COVER to the bottom of the

refrigerator cabinet. There are five screws total (4 for the hinge, 1 for the cover).

Important information about moving your refrigerator:

Your refrigerator is heavy. When moving the unit for cleaning or maintenance,

cover the floor with cardboard or hardboard to prevent damaging your floor.

You should always pull the refrigerator straight out when moving it. Do not

wiggle or “walk” the refrigerator when trying to move it, as this can cause floor

damage.

6. Move the BOTTOM HINGE and COVER each to the opposite side of the bottom of the

refrigerator cabinet. Completely tighten the four BOTTOM HINGE screws, and tighten the

COVER screw gently.

7. Remove the two screws fastening the

DOOR STOP SPACER and the DOOR

STOP to the bottom of the refrigerator

door, and move the spacer and stop to the

opposite sides.

8. Re-insert and completely tighten the

screws.

9. Install the refrigerator door onto the washer and hinge pin of the BOTTOM HINGE.

10. Align the top hinge WASHER with the HINGE HOLE in the top of the door. Then, insert

the TOP HINGE pin through the WASHER and into the HINGE HOLE.

11. Fasten the TOP HINGE with three screws and move the remaining four screws to the

opposite side. Completely tighten the seven screws.

Removing / Replacing the Base Grille

Required Tools: Phillips screwdriver

To remove the base grille:

1. Open the refrigerator door.

2. Remove the two SCREWS with a Phillips screwdriver. Release and remove the base grille

from the refrigerator by pushing both TABS in toward the center.

To replace the base grille:

1. Open the refrigerator door.

2. Align both TABS into position, such that the base grille snaps into place.

3. Replace and tighten the two SCREWS.

DISPOSING OF A WORN-OUT APPLIANCE

When an appliance finally wears out, dispose of it.

Before you dispose of your old appliance, take the door or doors off but leave the shelves

and drawers in place so that children cannot easily climb inside.

The refrigerating system of the appliance is filled with refrigerant and insulating substances

which should be separately recycled. Either have a licensed appliance repair company or

dealer remove the appliance or call your local recycling office for the appropriate disposal

information.

For the sake of environmental protection, be careful not to damage the rear wall of the

appliance (the condenser unit or the tubes when moving the appliance) or any part of the

refrigeration system inside the appliance.

This refrigerator is 100% CFC-free, but the coolant is under pressure and puncturing the

sealed system could be dangerous. The coolant used in the sealed system is non-toxic.

Many older appliances may contain refrigerants that are harmful to the environment, and

should be recycled by a lawfully licensed company.

Inhaltsverzeichnis

Andere Summit Kühlschrank Handbücher

Summit

Summit AZRF7W Bedienungsanleitung

Summit

Summit FF511L Bedienungsanleitung

Summit

Summit SP6DS-2D Bedienungsanleitung

Summit

Summit BDR190NASSTB Leitfaden

Summit

Summit FF1410 Bedienungsanleitung

Summit

Summit FF711ES Bedienungsanleitung

Summit

Summit FFAR10 Benutzerhandbuch

Summit

Summit AL750LSSHH Leitfaden

Summit

Summit FF71LLF2 Bedienungsanleitung

Summit

Summit FF63B Bedienungsanleitung

Summit

Summit FF6BI series Bedienungsanleitung

Summit

Summit SWC6G Series Bedienungsanleitung

Summit

Summit BI605FR Bedienungsanleitung

Summit

Summit FFAR22LW Bedienungsanleitung

Summit

Summit SCR-1300 Bedienungsanleitung

Summit

Summit FFBF192SSBI Bedienungsanleitung

Summit

Summit CP171 Series Bedienungsanleitung

Summit

Summit BDR190NASSHH Leitfaden

Summit

Summit ADRD18 Bedienungsanleitung

Summit

Summit CM45L Leitfaden

Summit

Summit SPR625OS Bedienungsanleitung

Summit

Summit BDR190NACSS Leitfaden

Summit

Summit FFBF279SSX Bedienungsanleitung

Summit

Summit FF-874W Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung