Sunjoy Rona 38115107 Bedienungsanleitung

Model / Modèle : 38115107

10’ x 12’ Gazebo

Operators’ Manual p. 2

Abri-soleil 10 x 12 pi

Guide de l'utilisateur p. 11

IMPORTANT:

1. Keep all children and pets away from assembly area. Children and pets should be

supervised while gazebo is being assembled.

2. The assembled gazebo should be located at least 6 feet (2 m) from any obstruction

such as a fence, garage, house, overhanging branches, laundry lines or electrical wires.

3. This unit is heavy. Do not assemble this item alone. Six people are recommended for

safe assembly.

4. Some parts may contain sharp edges. Wear protective gloves if necessary during

assembly.

5. When assembling and using this product, basic safety precautions should always be

followed to reduce the risk of personal injury and damage to equipment. Please read all

instructions before assembly and use.

6. For outdoor use only. Install on level ground. 16 stakes are provided to secure the

gazebo in the ground. If you wish to secure the pavilion to a wood deck or concrete

surface, use 16 anchors suited for these surfaces (anchors not included).

7. Check all bolts for tightness before and during usage.

8. Please check your state and local regulations prior to purchasing. Some jurisdictions

may require permits for installation and use. Some special procedures may be valid in

your area.

9. While this gazebo is manufactured to withstand strong force winds through only the

supplied ground stakes, securing the gazebo to a deck, concrete patio or a stronger base,

in areas subject to frequent severe weather should be considered.

NOTE: The gazebo’s roof and structure are not guaranteed against extreme weather

conditions (storms, high winds, etc.). If the gazebo is not dismantled for the winter, snow

must be cleaned off regularly. Any damage caused by snow accumulation is not covered

by the warranty.

GAZEBO ASSEMBLY INSTRUCTIONS

Our clear, easy-to-follow, step-by-step instructions will guide you through the

project from start to finish.

All that is required is a screwdriver, a hammer and two ladders of at least 8 feet

(2.5 m) high (not included).

For you safety, DO NOT assemble this item alone. Two people or more are

required for a smooth and safe installation.

Item identification: For ease of identification, all parts are labeled to correspond to

the Step number in which the part is used.

Description Part Quantity Image

Big panel 1 A1 2

Big panel 2 A2 2

Small panel 1 B1 2

Small panel 2 B2 2

Long beam 1 C1 2

Long beam 2 C2 2

Short beam D 2

Lower connector 1 E 4

Lower connector 2 F 6

Top frame G 1

Slanted beam H 4

Middle beam I 6

Long roof piece 1 J1 4

Long roof piece 2 J2 4

Short roof piece 1 J3 4

Short roof piece 2 J4 4

Middle roof piece J5 4

Parts List

Description Part Quantity Image

Small roof piece 1 K1 2

Small roof piece 2 K2 2

Left brace L1 4

Right brace L2 4

Middle brace L3 2

Long brace M1 2

Short brace M2 2

Left rail N1 4

Right rail N2 4

Middle rail N3 2

Center plate O1 6

Corner plate O2 8

Hook P 1

Small top connector Q 1

Cover R 1

Small slanted beam S 4

Long netting tube T 4

Short netting tube U 4

Mosquito netting V 1

Parts List

Part Description Quantity Image

AA M6X35 Bolt 4 PCS

BB M6 Flat washer 80 PCS

CC M6X15 Bolt 72 PCS

DD M6X20 Bolt 2 PCS

FF M6 Nut 2 PCS

Z M6 Wrench 2 PCS

Hardware Pack 1

Fig.1: Secure the small panels (B1 and B2) to the big panels (A1 and A2) with bolts (AA) and flat washers (BB).

Fig.2: Secure the lower connector 1 (E) to the corner of the panels with bolts (CC) and flat washers (BB).

Fig.3: Insert the long beam 1 (C1) into the long beam 2 (C2), then secure the long beam 1 (C1) to the long beam 2 (C2)

with bolts (CC), flat washers (BB), bolts (DD) and nuts (FF). Reserve one hole on the long beam 2 (C2) to assemble the

netting tube.

Part Description Quantity Image

BB M6 Flat washer38 PCS

CC M6X15 Bolt 18 PCS

DD M6X20 Bolt 20 PCS

Hardware Pack 2

Fig.7: Secure the top end of the slanted beam (H) to the top frame (G) with bolts (DD) and flat washers (BB).

Fig.8: Secure the slanted beam (H) to the lower connector 1 (E) with bolts (CC) and flat washers (BB).

Fig.9: Secure the middle beam (I) to the top beams (G) with bolts (DD) and flat washers (BB).

Fig.10: Secure the lower end of the middle beam (I) the lower connector 2 (F) with bolts (CC) and flat washers (BB).

Fig.4: Secure the assembled long beam 1 to the big panels (A1 and A2) with bolts (CC) and flat washers (BB). Repeat this step to

secure the short beam (D) to the small panels (B1 and B2).

Fig.5: Secure the lower connector 2 (F) and short netting tube (U) to the short beam (D) with bolts (CC) and flat washers (BB).

Fig.6: Secure the long netting tubes (T) to the long beams (C1 and C2) with bolts (CC) and flat washers (BB). Repeat this step to

secure the short netting tubes.

Fig.11: Secure the small slanted beam (S) to the top frame (G) with bolts (CC) and flat washers (BB).

Fig.12: Secure the small slanted beam (S) to the small top connector (Q) with bolts (CC) and flat washers (BB).

Fig.13: Attach the hook (P) to the small top connector (Q).

Part Description Quantity Image

AA M6X35 Bolt 2PCS

BB M6 Flat washer 16 PCS

EE M6X15 Screw 14 PCS

Hardware Pack 3

Fig.14: Insert the small roof pieces (K1 and K2) into the rail on the small slanted beam (S).

Fig.15: Insert the brace (M1 and M2) into the lower of the small roof piece (K1 and K2), then secure the corner

plate (O2) to the small slanted beam (S) through three holes with screws (EE) and flat washers (BB).

Fig.16: Secure the cover (R) to the small top connector (Q) with bolts (AA) and flat washers (BB).

Fig.17: Insert the short roof piece 1 (J3) and short roof piece 2 (J4) into the middle beam (I) and slanted beam (H), then

insert the rails (N1 and N2) into it. Insert the long roof piece (J1) into the middle beam (I) and slanted beam (H). Repeat this

step to install the right roof pieces.

Fig.18: Insert the middle roof piece (J5) into the middle beam (I); then insert the middle rail (N3) into it. Insert the middle roof

piece (J5) into the middle beam (I).

Fig.19: Insert the braces (L1, L2 and L3) into the lower roof pieces; then secure the center plate (O1) to the middle beam (I)

through three holes with screws (EE) and flat washers (BB).

Fig.20: Fig.20: Secure the corner plate (O2) to the slanted beam (H) through three holes with screws (EE) and flat washers

(BB).

Part Description Quantity Image

GG Ring 52 PCS

Hardware Pack 4

Part Description Quantity Image

HH Φ8X180mm Stake 16 PCS

Hardware Pack 5

Care & Maintenance:

Our steel components for garden accessories and furniture are treated with rust inhibiting

paint to protect it from rusting. However, due to the nature of steel, surface oxidation

(rusting) will occur once these protective coatings are scratched. This is not considered a

defect and thus cannot be covered by the warranty.

To minimize this condition, we recommend care when assembling & handling the product

to prevent scratching the paint. Should any scratching or damage occur, we recommend

immediate touch-up with rust inhibiting paint.

Surface rust can also be easily removed with a very light application of common cooking

oil. If surface oxidation (rusting) occurs and if no measure is taken to prevent this, the

oxidation may drip on to the deck or patio and caused damaging stains, which may be

difficult to remove. This can be prevented if the above-mentioned measures are taken to

keep the product from oxidizing.

Fig.21: Attach the mosquito netting (V) to the long netting tubes (T) and short tubes (U) with rings (GG).

Fig.22: Secure the whole gazebo to the ground with stakes (HH).

Your gazebo is now fully assembled.

Inhaltsverzeichnis

Sprachen:

Andere Sunjoy Gartenmöbel Handbücher

Sunjoy

Sunjoy L-GZ760PST-B Bedienungsanleitung

Sunjoy

Sunjoy A102009800 Bedienungsanleitung

Sunjoy

Sunjoy Thrshd Madaga Gazebo 10x10 Bedienungsanleitung

Sunjoy

Sunjoy A102000800 Bedienungsanleitung

Sunjoy

Sunjoy L-GZ339PAL Bedienungsanleitung

Sunjoy

Sunjoy L-GZ815PST Bedienungsanleitung

Sunjoy

Sunjoy BALI 147079 Bedienungsanleitung

Sunjoy

Sunjoy Catalina L-GZ660PST-D-MN Bedienungsanleitung

Sunjoy

Sunjoy A110000921 Beilage

Sunjoy

Sunjoy D-BS692SAL Bedienungsanleitung

Sunjoy

Sunjoy A103000102 Bedienungsanleitung

Sunjoy

Sunjoy L-GZ076PST-1A-4 Bedienungsanleitung

Sunjoy

Sunjoy A102032640 Bedienungsanleitung

Sunjoy

Sunjoy Sienna Octagon L-GZ240PST-A-PK Bedienungsanleitung

Sunjoy

Sunjoy Somerset L-GZ212PCO-B-PK Bedienungsanleitung

Sunjoy

Sunjoy 110211018-K Bedienungsanleitung

Sunjoy

Sunjoy L-GG030PST-B Hardtop Grill Gazebo Bedienungsanleitung

Sunjoy

Sunjoy L-BG011PST-1 Bedienungsanleitung

Sunjoy

Sunjoy SUMMERCOVE A106008600 Bedienungsanleitung

Sunjoy

Sunjoy A102016300 Bedienungsanleitung

Sunjoy

Sunjoy Aviano Bedienungsanleitung

Sunjoy

Sunjoy A102010000 Bedienungsanleitung

Sunjoy

Sunjoy A102007602 Bedienungsanleitung

Sunjoy

Sunjoy Catalina L-GZ660PST-D-PK Bedienungsanleitung

Beliebte Gartenmöbel Handbücher anderer Marken

Belleze

Belleze 014-HG-20074 Bedienungsanleitung

Hatteras Hammocks

Hatteras Hammocks DCA1-K-HH Bedienungsanleitung

Kozyard

Kozyard Morgan Aluminum Pergola Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5959 Installationshandbuch

OLT

OLT 24 Bedienungsanleitung

forest-style

forest-style HACIENDA 2354 Bedienungsanleitung

Courtyard Creations

Courtyard Creations RUS0188-WM Bedienungsanleitung

RPR

RPR OLLIE CHAIR Bedienungsanleitung

kingsley-bate

kingsley-bate MC-55 Bedienungsanleitung

Weltevree

Weltevree Carrier Bedienungsanleitung

Grange Fencing

Grange Fencing Elite Arch Bedienungsanleitung

Grosfillex

Grosfillex AUVENT YR14 Bedienungsanleitung

X-METAL

X-METAL EAGLE 33511 Bedienungsanleitung

Anova

Anova FBW6R Bedienungsanleitung

Outsunny

Outsunny 84A-090 Bedienungsanleitung

Ivy Terrace

Ivy Terrace IVTD212 Bedienungsanleitung

Breezesta

Breezesta FANBACK ADIRONDACK AD-0101 Bedienungsanleitung

hanit

hanit SUTTON 1 Bedienungsanleitung