Supermicro SuperBlade SBI-7228R-T2F2 Bedienungsanleitung

SBI-7228R-T2F2

SuperBlade Module

User’s Manual

Revison 1.0a

SBI-7228R-T2F2 SuperBlade Module User’s Manual

The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The

vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no

commitment to update or to keep current the information in this manual, or to notify any person or

organization of the updates. Please Note: For the most up-to-date version of this manual, please see

our web site at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product described

in this manual at any time and without notice. This product, including software and documentation, is the

property of Supermicro and/or its licensors, and is supplied only under a license. Any use or reproduction

of this product is not allowed, except as expressly permitted by the terms of said license.

IN NO EVENT WILLSUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,

SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE

THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH

DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FORANY HARDWARE,

SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF

REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE,

SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara

County in the State of California, USA. The State of California, County of Santa Clara shall be the

exclusive venue for the resolution of any such disputes. Supermicro's total liability for all claims will not

exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a ClassA digital

device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the manufacturer’s instruction manual, may cause harmful interference with radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference,

in which case you will be required to correct the interference at your own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning

applies only to products containing CR (Manganese Dioxide) Lithium coin cells. Perchlorate

Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate for further

details.

WARNING: HANDLING OF LEAD SOLDER MATERIALS USED IN THIS PRODUCT MAY

EXPOSE YOU TO LEAD, ACHEMICAL KNOWN TO THE STATE OF CALIFORNIA TO

CAUSE BIRTH DEFECTS AND OTHER REPRODUCTIVE HARM.

Manual Revison 1.0a

Release Date: April 18, 2016

Unless you request and receive written permission from Super Micro Computer, Inc., you may not copy

any part of this document.

Information in this document is subject to change without notice. Other products and companies referred

to herein are trademarks or registered trademarks of their respective companies or mark holders.

Printed in the United States of America

iii

Preface

About this Manual

This manual is written for professional system integrators, Information Technology

professionals, service personnel and technicians. It provides information for the

installation and use of the Supermicro SuperBlade®system’s SBI-7228R-T2F2

SuperBlade module. Installation and maintenance should be performed by experienced

professionals only.

Manual Organization

Chapter 1: Introduction

The first chapter provides a checklist of the main components included with

SBI-7228R-T2F2 SuperBlade module and describes their main features.

Chapter 2: System Safety

You should familiarize yourself with this chapter for a general overview of safety

precautions that should be followed when installing and servicing SBI-7228R-T2F2

SuperBlade module.

Chapter 3: Setup and Installation

Refer to this chapter for details on installing the SBI-7228R-T2F2 SuperBlade module

into the SuperBlade chassis. Other sections cover the installation and placement of

memory modules and the installation of hard disk drives into the blade module.

Chapter 4: Blade Module Features

This chapter coves features and component information about SBI-7228R-T2F2

SuperBlade module. Included here are descriptions and information for mainboard

components, connectors, LEDs and other features of the blade module.

Chapter 5: BIOS

BIOS setup is covered in this chapter for SBI-7228R-T2F2 SuperBlade module.

Appendix A: BIOS POST Codes

BIOS POST Codes for SBI-7228R-T2F2 SuperBlade module are explained in this

appendix.

SBI-7228R-T2F2 SuperBlade Module User’s Manual

Notes

Table of Contents

Chapter 1 Introduction.......................................................................1-1

1-1 Overview.............................................................................................1-1

1-2 Product Checklist of Typical Components.....................................1-1

1-3 Blade Module Features....................................................................1-2

Processors..............................................................................................1-2

Memory...................................................................................................1-2

Storage ...................................................................................................1-3

RAID .......................................................................................................1-3

Density....................................................................................................1-3

1-4 Contacting Supermicro.....................................................................1-4

Chapter 2 Standardized Warning Statements.....................2-1

2-1 About Standardized Warning Statements .....................................2-1

Warning Definition...................................................................................2-1

Installation Instructions ...........................................................................2-3

Circuit Breaker........................................................................................2-4

Power Disconnection Warning................................................................2-5

Equipment Installation.............................................................................2-6

Restricted Area .......................................................................................2-7

Battery Handling .....................................................................................2-9

Redundant Power Supplies ..................................................................2-10

Backplane Voltage................................................................................2-11

Comply with Local and National Electrical Codes.................................2-12

Product Disposal...................................................................................2-13

Hot Swap Fan Warning.........................................................................2-14

Power Cable and AC Adapter ..............................................................2-15

Chapter 3 Setup and Installation.................................................3-1

3-1 Overview.............................................................................................3-1

3-2 Installing Blade Modules..................................................................3-1

Powering Up a Blade Unit.......................................................................3-1

Powering Down a Blade Unit ..................................................................3-1

Removing a Blade Unit from the Enclosure............................................3-2

Removing/Replacing the Blade Cover....................................................3-2

Installing a Blade Unit into the Enclosure ...............................................3-2

SBI-7228R-T2F2 SuperBlade Module User’s Manual

3-3 Processor Installation.......................................................................3-4

3-4 Onboard Battery Installation............................................................3-9

3-5 Memory Installation...........................................................................3-9

Populating Memory Slots........................................................................3-9

DIMM Installation..................................................................................3-12

3-6 Hard Disk Drive Installation...........................................................3-13

3-7 Installing the Operating System....................................................3-14

Installing with an External USB CD-ROM Drive....................................3-14

Installing via PXE Boot..........................................................................3-14

Installing via Virtual Media (Drive Redirection) .....................................3-14

3-8 Management Software...................................................................3-15

3-9 Configuring and Setting up RAID.................................................3-15

Chapter 4 Blade Module Features..............................................4-1

4-1 Control Panel.....................................................................................4-2

Power Button ..........................................................................................4-3

KVM Button.............................................................................................4-3

LED Indicators ........................................................................................4-3

KVM Connector.......................................................................................4-3

4-2 Mainboard...........................................................................................4-4

Jumpers..................................................................................................4-6

CMOS Clear............................................................................................4-6

4-3 Blade Unit Components...................................................................4-7

Memory Support .....................................................................................4-8

Hard Disk Drives.....................................................................................4-8

Chapter 5 BIOS.......................................................................................5-1

5-1 Introduction.........................................................................................5-1

System BIOS ..........................................................................................5-1

How To Change the Configuration Data .................................................5-1

Starting the Setup Utility .........................................................................5-1

5-2 BIOS Updates....................................................................................5-2

Flashing BIOS.........................................................................................5-2

5-3 Running Setup...................................................................................5-3

5-4 Main BIOS Setup...............................................................................5-4

5-5 Advanced Setup ................................................................................5-6

5-6 Event Logs Setup............................................................................5-17

5-7 IPMI Setup........................................................................................5-19

vii

5-8 Security.............................................................................................5-19

5-9 Boot...................................................................................................5-20

5-10 Save & Exit.....................................................................................5-21

SBI-7228R-T2F2 SuperBlade Module User’s Manual

viii

Notes

1-1

Chapter 1

Introduction

1-1 Overview

This user’s manual covers the SBI-7228R-T2F2 blade module. This blade module is a

compact self-contained server that connects into a pre-cabled enclosure that provides

power, cooling, management and networking functions. One enclosure for the

SBI-7228R-T2F2 blade module can hold ten blade units. Each blade module has two

nodes for a total of twenty nodes.

In this manual, “blade system” refers to the entire system (including the enclosure and

blades units), “blade” or “blade unit” refers to a single blade module, “Node” refers to a

single node in each blade module (two per module) and “blade enclosure” is the chassis

that the blades, power supplies and modules are housed within.

Please refer to our web site for information on operating systems that have been

certified for use with the SuperBlade (www.supermicro.com/products/superblade/).

Note: For your system to work properly, please follow the links below to download all

necessary drivers/utilities and the user’s manual for your server.

• Supermicro product manuals: http://www.supermicro.com/support/manuals/

• Product drivers and utilities: ftp://ftp.supermicro.com

• Product safety information: http://super-dev/about/policies/safety_information.cfm

• If you have any questions, please contact our support team at:

support@supermicor.com

Note: A complete list of safety warnings is provided on the Supermicro web site at

http://www.supermicro.com/about/policies/safety_information.cfm.

1-2 Product Checklist of Typical Components

Your blade module ships with its B10DRT-IBF2 mainboard already installed in its

chassis. Memory, hard disk drives and the CPU must all be installed by the user after

shipment. See Chapter 3: "Setup and Installation" on page 3-1 for details on installation

of these components.

The blade module’s serverboard includes an InfiniBand chip (one per node) for your

blade module, which allows you to use InfiniBand communication for your blade module.

SBI-7228R-T2F2 SuperBlade Module User’s Manual

1-2

1-3 Blade Module Features

Table 1-1 lists the main features of the SBI-7228R-T2F2 blade module. See the

proceeding section for components typically included in a blade system and other

optional components. Specific details for the SBI-7228R-T2F2 blade module are found

in Chapter 4: "Blade Module Features" on page 4-1.

Processors

The SBI-7228R-T2F2 SuperBlade module supports four 2011-pin Socket R (LGA 2011)

Intel Xeon E5-2600 V3/V4 series processors grouped two per node.

Refer to the Supermicro web site for a complete listing of supported processors (http://

www.supermicro.com/products/superblade). Please note that you will need to check the

detailed specifications of a particular blade module for a list of the CPUs it supports.

Details on installation of the processor into the SBI-7228R-T2F2 SuperBlade module

are found in Chapter 3: "Setup and Installation" on page 3-1.

Memory

Both the SBI-7228R-T2F2 SuperBlade module have eight (8) 288-pin DIMM sockets

that can support up to 512 GB RDIMM or 1 TB LRDIMM DDR4 2400/2133/1866/1600

MHz speed, 128 GB, 64 GB, 32 GB, 16 GB, 8 GB and 4 GB size SDRAM memory per

node. Memory is interleaved, which requires modules of the same size and speed to be

installed in groups (of two or three).

Please refer to the Supermicro web site for a list of supported memory

(www.supermicro.com/products/superblade). The detailed specifications for a blade

module will contain a link to a list of recommended memory sizes and manufacturers.

Table 1-1. SBI-7228R-T2F2 SuperBlade Module Specification Features

Mainboard B10DRT-IBF2 (proprietary form factor)

Chassis Dimensions (HxWxD): 11.32" x 1.67" x 20.5" (288-mm x 42-mm x

521-mm)

Processors Four eight/six/four core Intel™Xeon®E5-2600 V3/V4 series 2011-pin

processors. Two of these processors are available for each node. Please

refer to our web site for a complete listing of supported processors.

QPI Speed QPI up to 9.6 GT/s

Chipset One Intel C612 chip set for each node

Graphics Controller Integrated Aspeed AST 2400 VGA Graphics chip for each node

BIOS 128 Mb SPI Flash EEPROM withAMI® BIOS for each node

Memory Capacity Supports up to 512 GB of RDIMM or 1 TB of LRDIMM DDR4 2400/2133/

1866/1600 MHz speed and 128 GB, 64 GB, 32 GB, 16 GB, 8 GB and 4 GB

size SDRAM memory in eight (8) 288-pin DIMM sockets for each node

Hard Drive Bays Includes four hot-swap drive bays for 2.5" SATA/SSD disk drives (two per

node), and two internal SATADOM (one per node)

Inhaltsverzeichnis

Andere Supermicro Steuereinheit Handbücher

Supermicro

Supermicro AOC-ATG-i2T2SM Bedienungsanleitung

Supermicro

Supermicro MicroBlade MBI-6118G-T81X Bedienungsanleitung

Supermicro

Supermicro SBA-7141M-T Bedienungsanleitung

Supermicro

Supermicro MicroBlade MBI-6119M-T2N Bedienungsanleitung

Supermicro

Supermicro MicroBlade MBI-6119G-C2 Bedienungsanleitung

Supermicro

Supermicro MicroBlade MBI-6218G-T41X Bedienungsanleitung

Supermicro

Supermicro AOC-ATG-i2S Bedienungsanleitung

Supermicro

Supermicro MicroBlade MBI-6119G-C4 Bedienungsanleitung

Supermicro

Supermicro AOC-AH25G-m2S2TM Bedienungsanleitung

Supermicro

Supermicro SuperBlade SBI-4129P-T3N Bedienungsanleitung

Supermicro

Supermicro SuperBlade SBI-7128R-C6N Bedienungsanleitung

Supermicro

Supermicro SBI-7147R-S4X Bedienungsanleitung

Supermicro

Supermicro MicroBlade MBI-6218G-T81X Bedienungsanleitung

Supermicro

Supermicro SBI-6129P-T3N Bedienungsanleitung

Supermicro

Supermicro SuperBlade SBI-8149P-C4N Bedienungsanleitung

Supermicro

Supermicro SBI-6419P-T3N Bedienungsanleitung

Supermicro

Supermicro MBI-6219G-T Bedienungsanleitung

Supermicro

Supermicro MicroBlade MBI-6118G-T41X Bedienungsanleitung

Supermicro

Supermicro MBI-6128R-T2 Bedienungsanleitung

Supermicro

Supermicro SBI-4429P-T2N Bedienungsanleitung

Supermicro

Supermicro SBM-25G-P10 Bedienungsanleitung

Supermicro

Supermicro MicroBlade MBI-6119M-C2 Bedienungsanleitung

Supermicro

Supermicro SuperBlade SBI-6419P-C3N Bedienungsanleitung

Supermicro

Supermicro SBI-7228R-T2X Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung