Supermicro SBI-7228R-T2F Bedienungsanleitung

SBI-7228R-T2F

Blade Module

User’s Manual

Revison 1.0

SBI-7228R-T2F Blade Module User’s Manual

The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The

vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no

commitment to update or to keep current the information in this manual, or to notify any person or

organization of the updates. Please Note: For the most up-to-date version of this manual, please see

our web site at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product described

in this manual at any time and without notice. This product, including software and documentation, is the

property of Supermicro and/or its licensors, and is supplied only under a license. Any use or reproduction

of this product is not allowed, except as expressly permitted by the terms of said license.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,

SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE

THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH

DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY HARDWARE,

SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF

REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE,

SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara

County in the State of California, USA. The State of California, County of Santa Clara shall be the

exclusive venue for the resolution of any such disputes. Supermicro's total liability for all claims will not

exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class A digital

device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the manufacturer’s instruction manual, may cause harmful interference with radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference,

in which case you will be required to correct the interference at your own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning

applies only to products containing CR (Manganese Dioxide) Lithium coin cells. Perchlorate

Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate for further

details.

WARNING: HANDLING OF LEAD SOLDER MATERIALS USED IN THIS PRODUCT MAY

EXPOSE YOU TO LEAD, A CHEMICAL KNOWN TO THE STATE OF CALIFORNIA TO

CAUSE BIRTH DEFECTS AND OTHER REPRODUCTIVE HARM.

Manual Revison 1.0

Release Date: October 30, 2014

Unless you request and receive written permission from Super Micro Computer, Inc., you may not copy

any part of this document.

Information in this document is subject to change without notice. Other products and companies referred

to herein are trademarks or registered trademarks of their respective companies or mark holders.

Printed in the United States of America

iii

Preface

About this Manual

This manual is written for professional system integrators, Information Technology

professionals, service personnel and technicians. It provides information for the

installation and use of the Supermicro SuperBlade®system’s SBI-7228R-T2F blade

module. Installation and maintenance should be performed by experienced

professionals only.

Manual Organization

Chapter 1: Introduction

The first chapter provides a checklist of the main components included with

SBI-7228R-T2F blade module and describes their main features.

Chapter 2: System Safety

You should familiarize yourself with this chapter for a general overview of safety

precautions that should be followed when installing and servicing SBI-7228R-T2F blade

module.

Chapter 3: Setup and Installation

Refer to this chapter for details on installing the SBI-7228R-T2F blade module into the

SuperBlade chassis. Other sections cover the installation and placement of memory

modules and the installation of hard disk drives into the blade module.

Chapter 4: Blade Module Features

This chapter coves features and component information about SBI-7228R-T2F blade

module. Included here are descriptions and information for mainboard components,

connectors, LEDs and other features of the blade module.

Chapter 5: BIOS

BIOS setup is covered in this chapter for SBI-7228R-T2F blade module.

Appendix A: BIOS POST Codes

BIOS POST Codes for SBI-7228R-T2F blade module are explained in this appendix.

SBI-7228R-T2F Blade Module User’s Manual

Notes

Table of Contents

Chapter 1 Introduction.......................................................................1-1

1-1 Overview.............................................................................................1-1

1-2 Product Checklist of Typical Components.....................................1-1

1-3 Blade Module Features....................................................................1-2

Processors..............................................................................................1-2

Memory...................................................................................................1-2

Storage....................................................................................................1-3

RAID .......................................................................................................1-3

Density....................................................................................................1-3

1-4 Contacting Supermicro.....................................................................1-4

Chapter 2 Standardized Warning Statements.....................2-1

2-1 About Standardized Warning Statements......................................2-1

Warning Definition...................................................................................2-1

Installation Instructions ...........................................................................2-3

Circuit Breaker........................................................................................2-4

Power Disconnection Warning................................................................2-5

Equipment Installation.............................................................................2-6

Restricted Area.......................................................................................2-7

Battery Handling .....................................................................................2-9

Redundant Power Supplies ..................................................................2-10

Backplane Voltage................................................................................2-11

Comply with Local and National Electrical Codes.................................2-12

Product Disposal...................................................................................2-13

Hot Swap Fan Warning.........................................................................2-14

Power Cable and AC Adapter ..............................................................2-15

Chapter 3 Setup and Installation.................................................3-1

3-1 Overview.............................................................................................3-1

3-2 Installing Blade Modules..................................................................3-1

Powering Up a Blade Unit.......................................................................3-1

Powering Down a Blade Unit ..................................................................3-1

Removing a Blade Unit from the Enclosure............................................3-2

Removing/Replacing the Blade Cover....................................................3-2

Installing a Blade Unit into the Enclosure ...............................................3-2

SBI-7228R-T2F Blade Module User’s Manual

3-3 Processor Installation.......................................................................3-4

3-4 Onboard Battery Installation............................................................3-9

3-5 Memory Installation...........................................................................3-9

Populating Memory Slots........................................................................3-9

DIMM Installation ..................................................................................3-11

3-6 Hard Disk Drive Installation...........................................................3-12

3-7 Installing the Operating System....................................................3-13

Installing with an External USB CD-ROM Drive....................................3-13

Installing via PXE Boot..........................................................................3-13

Installing via Virtual Media (Drive Redirection) .....................................3-13

3-8 Management Software...................................................................3-14

3-9 Configuring and Setting up RAID .................................................3-14

Chapter 4 Blade Module Features..............................................4-1

4-1 Control Panel.....................................................................................4-2

Power Button ..........................................................................................4-3

KVM Button.............................................................................................4-3

LED Indicators ........................................................................................4-3

KVM Connector.......................................................................................4-3

4-2 Mainboard...........................................................................................4-4

Jumpers..................................................................................................4-6

CMOS Clear............................................................................................4-6

4-3 Blade Unit Components...................................................................4-7

Memory Support .....................................................................................4-8

Hard Disk Drives.....................................................................................4-8

Chapter 5 BIOS.......................................................................................5-1

5-1 Introduction.........................................................................................5-1

System BIOS ..........................................................................................5-1

How To Change the Configuration Data .................................................5-1

Starting the Setup Utility..........................................................................5-1

5-2 BIOS Updates....................................................................................5-2

Flashing BIOS.........................................................................................5-2

5-3 Running Setup...................................................................................5-3

5-4 Main BIOS Setup...............................................................................5-4

5-5 Advanced Setup................................................................................5-6

5-6 Event Logs Setup............................................................................5-17

5-7 IPMI Setup........................................................................................5-19

vii

Table of Contents

5-8 Security.............................................................................................5-19

5-9 Boot...................................................................................................5-20

5-10 Save & Exit.....................................................................................5-21

Appendix A AMI UEFI BIOS POST Codes..............................A-1

A-1 Checkpoint Ranges..........................................................................A-1

A-2 Standard Checkpoints......................................................................A-2

A-3 OEM-Reserved Checkpoint Ranges .............................................A-9

SBI-7228R-T2F Blade Module User’s Manual

viii

Notes

1-1

Chapter 1

Introduction

1-1 Overview

This user’s manual covers the SBI-7228R-T2F blade module. This blade module is a

compact self-contained server that connects into a pre-cabled enclosure that provides

power, cooling, management and networking functions. One enclosure for the

SBI-7228R-T2F blade module can hold ten blade units. Each blade module has two

nodes for a total of twenty nodes.

In this manual, “blade system” refers to the entire system (including the enclosure and

blades units), “blade” or “blade unit” refers to a single blade module, “Node” refers to a

single node in each blade module (two per module) and “blade enclosure” is the chassis

that the blades, power supplies and modules are housed within.

Please refer to our web site for information on operating systems that have been

certified for use with the SuperBlade (www.supermicro.com/products/superblade/).

Note: For your system to work properly, please follow the links below to download all

necessary drivers/utilities and the user’s manual for your server.

• Supermicro product manuals: http://www.supermicro.com/support/manuals/

• Product drivers and utilities: ftp://ftp.supermicro.com

• Product safety information: http://super-dev/about/policies/safety_information.cfm

• If you have any questions, please contact our support team at:

support@supermicor.com

Note: A complete list of safety warnings is provided on the Supermicro web site at

http://www.supermicro.com/about/policies/safety_information.cfm.

1-2 Product Checklist of Typical Components

Your blade module ships with its B10DRT-TP mainboard already installed in its chassis.

Memory, hard disk drives and the CPU must all be installed by the user after shipment.

See Chapter 3: "Setup and Installation" on page 3-1 for details on installation of these

components.

The blade module’s serverboard includes an InfiniBand chip (one per node) for your

blade module, which allows you to use InfiniBand communication for your blade module.

SBI-7228R-T2F Blade Module User’s Manual

1-2

1-3 Blade Module Features

Table 1-1 lists the main features of the SBI-7228R-T2F blade module. See the

proceeding section for components typically included in a blade system and other

optional components. Specific details for the SBI-7228R-T2F blade module are found in

Chapter 4: "Blade Module Features" on page 4-1.

Processors

The SBI-7228R-T2F blade module supports four 2011-pin Socket R (LGA 2011)

E5-2600 (V3) series processors grouped two per node.

Refer to the Supermicro web site for a complete listing of supported processors (http://

www.supermicro.com/products/superblade). Please note that you will need to check the

detailed specifications of a particular blade module for a list of the CPUs it supports.

Details on installation of the processor into the SBI-7228R-T2F blade module are found

in Chapter 3: "Setup and Installation" on page 3-1.

Memory

Both the SBI-7228R-T2F blade module have eight (8) 288-pin DIMM sockets that can

support up to 256 GB RDIMM or 512 GB LRDIMM DDR4 2133/1866/1600/1333/1066/

800 MHz speed, 64GB, 32GB, 16GB, 8GB, 4GB, 2GB and 1GB size SDRAM memory

per node. Memory is interleaved, which requires modules of the same size and speed to

be installed in groups (of two or three).

Please refer to the Supermicro web site for a list of supported memory

(www.supermicro.com/products/superblade). The detailed specifications for a blade

module will contain a link to a list of recommended memory sizes and manufacturers.

Table 1-1. SBI-7228R-T2F Blade Module Specification Features

Mainboard B10DRT-TP (proprietary form factor)

Chassis Dimensions (HxWxD): 11.32" x 1.67" x 20.5" (288-mm x 42-mm x

521-mm)

Processors Four eight/six/four core Intel™Xeon®E5-2600 (V3) series 2011-pin

processors. Two of these processors are available for each node. Please

refer to our web site for a complete listing of supported processors.

QPI Speed QPI up to 9.6 GT/s

Chipset One Intel C612 chip set for each node

Graphics Controller Integrated Aspeed AST 2400 VGA Graphics chip for each node

BIOS 128 Mb SPI Flash EEPROM with AMI® BIOS for each node

Memory Capacity

Supports up to 256 GB of RDIMM or 512 GB of LRDIMM DDR4 2133/

1866/1600/1333/1066/800 MHz speed and 64GB, 32GB, 16GB, 8GB,

4GB, 2GB and 1GB size SDRAM memory in eight (8) 288-pin DIMM

sockets for each node

Hard Drive Bays Includes four hot-swap drive bays for 2.5" SATA/SSD disk drives (two per

node), and two internal SATADOM (one per node)

Inhaltsverzeichnis

Andere Supermicro Server Handbücher

Supermicro

Supermicro SuperServer 1019D-FRN8TP Bedienungsanleitung

Supermicro

Supermicro AS-1041M-82 Bedienungsanleitung

Supermicro

Supermicro SuperServer 1027R-WTRFTP Bedienungsanleitung

Supermicro

Supermicro SuperServer SYS-221P-C9R Bedienungsanleitung

Supermicro

Supermicro SuperServer 1029GP-TR Bedienungsanleitung

Supermicro

Supermicro AS-3014TS-i Bedienungsanleitung

Supermicro

Supermicro SUPERSERVER 6028U-T Series Bedienungsanleitung

Supermicro

Supermicro SYS-1028UX-LL1-B8 Bedienungsanleitung

Supermicro

Supermicro SUPERSERVER 6016T-URF4+ Bedienungsanleitung

Supermicro

Supermicro SuperServer 1029U-TN10RT Bedienungsanleitung

Supermicro

Supermicro SuperServer SSG-641E-E1CR24H Bedienungsanleitung

Supermicro

Supermicro 5015M-T Bedienungsanleitung

Supermicro

Supermicro SuperServer 1029UX-LL1-S16 Bedienungsanleitung

Supermicro

Supermicro SUPERSERVER 1028R-TDW Bedienungsanleitung

Supermicro

Supermicro SuperServer 5019D-RN8TP Bedienungsanleitung

Supermicro

Supermicro SSG-5049P-E1CR45L Betriebsanleitung

Supermicro

Supermicro MicroBlade MBE-628L-416 Bedienungsanleitung

Supermicro

Supermicro SUPERSERVER 4029GP-TVRT Bedienungsanleitung

Supermicro

Supermicro AS-2114GT-DPNR Bedienungsanleitung

Supermicro

Supermicro SuperServer E301-9D-8CN8TP Bedienungsanleitung

Supermicro

Supermicro SuperServer 1029P-NR32R Bedienungsanleitung

Supermicro

Supermicro SuperServer SYS-221HE-FTNR Bedienungsanleitung

Supermicro

Supermicro SuperServer 120C-TR Bedienungsanleitung

Supermicro

Supermicro SuperServer 1019C-HTN2 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung