Supore CS-700 Bedienungsanleitung

Combined Table CS-700

Operation Manual

REV.20160201

PREFACE

INTRODUCTION:

Combined Table CS-700 is a precise instrument which can be used with Refractometer, Slit Lamp, Vi

ew Tester, Chart Projector etc. It makes the operation of other instruments convenient and precise. Luxur

ious leather chair is quite quiet when operating. Luxurious swing arm can move freely, can the work tab

le can circumrotate for 90 degree. This can save a lot of installation space. The tray can be moved with

a refractometer mobile tray, the CD drawer to put the refractometer tray.

SAFETY INFORMATION

1.Safety symbols and instructions

The arrow direction and the table in the same direction

2.Using environment and notes

1) Read and understand all instructions.

2) Using under the operation and the warning on the main machine.

3) Please do not near the water using the instrument, do not use or place the instrument in damp places

4) Please place the instrument smooth on solid ground. Otherwise, the machine falls can lead serious da

mage or injuries.

5) When installing a good instrument, please check up the installed correctly, and access to the total po

wer supply, when stop using for a long time, should cut off power supply.

6) When cleaning the instrument, please pull out the machine power plug, make sure to cut off all the

power. Please use the wet cloth to wipe, power can be supplied after all dry. (Cleaning inside after tear

down the machine is forbidden)

7) When malfunction or abnormal phenomenon occurred, please immediately cut off the power and conta

ct maintenance personnel, do not handle by yourself.

8)According to the product principle, working mode and characteristics of this product, do not need to st

erilize, and don't have to prevent the radiation protection

Catalog

、

Introduction ...................................................................................................................................................... 3

1.Main machine ..............................................................................................................................................3

2.Operation Panel parts detailed introduction ..............................................................................................3

、

Using instruction .............................................................................................................................................. 4

1.Installation ..................................................................................................................................................4

2.Adjustment..................................................................................................................................................7

3.Test and use.................................................................................................................................................... 7

、

Maintaince .......................................................................................................................................................... 8

1.Daily Maintaince .........................................................................................................................................8

2.Meterial replacement ....................................................................................................................................8

3.Cleaning .........................................................................................................................................................8

4.Moving machine notes ..................................................................................................................................8

5.Service information .....................................................................................................................................8

、

Simple fault phenomenon and removing ....................................................................................................... 8

Fuse replacement method................................................................................................................................8

、

Performacnce parameter................................................................................................................................... 8

、

Attachment list ................................................................................................................................................. 9

、

Introduction

1.) Main machine

2.)Operation Panel parts detailed introduction

On Off Chair up Chair down Test Rest Up Down

、

Using instruction

1.)Installation

（Be sure ：Installation room is more than L5M×W2M×H 2M ）

Step：1）Remove the host honeycomb carton top and side panel

2）Dismantle the host packaging materials, take out the ⑦pedal parts and ⑧Projector base parts.

3）Take down packaging materials, open the host side ,the fixed screw will be unloaded with a wrench

（See Figure 1.）

4）Take out the main machine from the wooden tray.

Figure 1.

5)Put the machine on the smooth and solid ground, install the ⑦pedal parts: Unload four solid screw from

the pedal plate.（See figure 2），remove cover plate and take out the holder. Fix the holder and the main machine,

cover the plate and fix the screw in the pedal plate.(See picture 3.)

Figure2 Fig 3

Pedal

Plate

Holder

6）Take out the ⑤table parts,③arm parts ④chart projector material and installation parts

7)⑤table parts installation 1：Take out the right side plate(see the figure .Put the mesa

cable through from the flange thread hole

figure 4

8) ⑤table parts installation 2：

Put the mesa cable through from the flange thread hole,The mesa with four screws along

the direction of arrow and flange fixed tightly(see figure 5.)

Figure5

9) ⑤table parts installation 2：( See figure 6)

Take out the right side

The table direction should be the

same as the arrow direction

Lock firmly as the arrow

direction

Install the right plate

Figure6

10) ③The installation of swing arm part 1Connect the general power, turn on the power

switch, press the up button to move the arm up the highest(for a easier screw installation )

11) ③he installation of swing arm part 2：Turn off the general power, connect the arm power line

with the plug in and fix the arm .Then put the view tester hanger arm into the swing arm

firmly.(Figure 7)

Figure 7

12）⑧The installation of the projector base parts(See figure 8 )

There are two holes,to

fix on the table by

screw

Figure 8

13)The connection of the Chair :Put the chair on the side of the main machine and the center of the

table .Using chair Connecting line to connect the main machine and the back of the chair.

2.Adjustment

1)Check whether the host place is smooth, adjustable screw host level.

2）Turn on the power switch, power indicator is on .

3)The workboard can revolve steadily and flexibly (the range is 90°).

4)Press the left and right keys of the swing arm, it can swing steadily and without noise (the range is 30°).

5)Press the up and down keys of the swing arm, it can swing steadily, without noise when lifting up and down

(the range is 20cm).

6) Press the light key, and it must run in good condition.

7) Check whether the chair is set on horizontal ground or not by adjusting the four floor mats. When lifting the

chair up & down, the chair runs steadily and without nose (the range is 20cm).

8) Check whether the power supply for the work board and chart projector are all right or not.

3.Test and use

1)Rotate the table 90 degrees anticlockwise. Patient can easily sit on the chair.

2)Rotate the table 90 degrees clockwise to the front of the patient to us the refractometer ,return t

o original when finished.

3)Turn on the power of the projector to check.

4)Turn on the arm switch, and let Specimens comprehensive instrument to the front of the patien

t, to adjust the height of the chair using the up and down switch to the right height to conform to the

right height of the Specimens comprehensive instrument ,the arm return to the original location when fin

ished.

5)Rotate the table 90 degrees anticlockwise., press the down key in the chair to down the extreme

lower to move the table easily.

6)Turn off the power ，and pull out the power line for not using for a long time .

5. Maintenance

1.Daily Maintenance

Turn off the general power when not using the machine long time. Check the power line regularly.

2.Material replacement

It is unnecessary to change the material, when the abnormal appear, such as the fuse burned, please change the

corresponding type fuse .

3.Cleaning

When cleaning, please pull out the power plug to be sure all the power cut off. Please use the wet cloth to clean,

the power can be in after all dry. Cleaning inside is forbidden. The power plug is forbidden to be cleaned by the wet

cloth.

4.Moving machine notes

Please pull out the plug when moving the power plug. When moving to confirm there no other instrument on

the machine. Notice the power line when moving to prevent broken.

5.Service information

Firstly cut off the power when abnormal appear, and then consult the sales department of the after sales

department.

、

Imple fault phenomenon and removing

Fuse replacement method

A) Shut off the power switch, pull the power cord

B) Use a screwdriver set aside fuse hat, remove damaged fuse;

C) Change a fuse of the same rating, down into the fuse cap, end of fuse replacement.

、

Performacnce parameter

－

700 feature:

Table rotating scope：90°

Arm left-right moving scope: 60°

Arm up and down scope: 200mm

Table area: length 950* width 460* height 30 (mm)

Refractometer salver area: length 560*width 460*height 24 (mm)

Draw inside room: length 570*width 385*height 60 (mm)

Power supply: AC220V/110V 50HZ

Power: 350VA

Light: fluorescent lamp (20W)

Net weight: 240KG

、

Attachment list

CS-700 spare parts

Item

Name

Picture

Parts Number

Quantity

Remar

View tester

arm

①

Projector steel

plate

②

Swing arm

plate

③

Projector type

steel

④

Table parts

⑤

Inhaltsverzeichnis

Andere Supore Laborausrüstung Handbücher

Supore

Supore RMK-700 Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung