Swann GuardianEye Bedienungsanleitung

GuardianEye

Monitoring System

INSTRUCTION MANUAL

Important Information

FCC Verification

This equipment has been tested and found to comply with the limits for

Class B digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interfer-

ence in a residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used in ac-

cordance with the instructions, may cause harmful interference to radio

or television reception, which can be determined by turning the equip-

ment off and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

These devices comply with part 15 of the FCC Rules. Operation is sub-

ject to the following two conditions:

• These devices may not cause harmful interference

• These devices must accept any interference received, including in-

terference that may cause undesired operation

Important Notice - All jurisdictions have specific laws and regulations

relating to the use of cameras. Before using any camera for any pur-

pose, it is the buyer’s responsibility to be aware of all applicable laws

and regulations that prohibit or limit the use of cameras and to comply

with the applicable laws and regulations.

FCC Regulation (for USA): Prohibition against eavesdropping

Except for the operations of law enforcement officers conducted under

lawful authority, no person shall use, either directly or indirectly, a de-

vice operated pursuant to the provisions of this Part for the purpose

of overhearing or recording the private conversations of others unless

such use is authorized by all of the parties engaging in the conversation.

Warning - Changes or modifications made to this device not approved

expressly by the party responsible for compliance could void the user’s

authority to operate the equipment.

Important Safety Instructions

• Make sure product is fixed correctly and stable if fastened in place

• Do not operate if wires and terminals are exposed

• Do not cover vents on the side of the device and allow adequate space

for ventilation

• Only use the power adapter supplied with your NVR

Password Information

Your NVR does not have a default password. A password is created dur-

ing the Wizard. If password protection has been enabled and you have

forgotten your password, please contact Swann Helpdesk & Technical

Support for assistance (contact numbers on the last page).

About this Manual

This instruction manual is written for the GuardianEye Monitoring Sys-

tem and was accurate at the time it was completed. However, because

of our on-going efforts to constantly improve our products, additional

features and functions may have been added since that time. We en-

courage you to visit our website to check for the latest updates.

Contents

Important Information 2

Contents 3

Chapter 1: Live View 4

Live View Mode 5

Live View Icons 6

Chapter 2: Menu 7

Menu Layout 8

Chapter 3: Camera Configuration 9

Recording: Encode 10

Channel: Device List 11

Motion 12

Motion: Motion Detection 13

Motion: Schedule 14

Motion Detection Tips 15

Chapter 4: Recording Configuration 16

Recording Schedule 17

Chapter 5: Playback & Backup 18

Search: Video Search 19

The Playback Interface 20

Search: Backup 21

Chapter 6: System Configuration 22

System: General 23

Daylight Saving 24

System: HDD 25

System: Maintenance 26

Network: General 27

Network: Advanced 28

Email Settings 29

Network: WIFI Setting 30

System: System Information 31

Troubleshooting 32

Glossary 34

Warranty Information 36

Helpdesk & Technical Support 37

Live View

Live View is the default display mode

for your NVR. Each camera connected

will be displayed on-screen. You can

check the status or operation of your

NVR and cameras using the status

icons and Menu Bar on the Live View

screen. Right-click the mouse to ac-

cess the Menu Bar.

26/05/2015 9:30:15 Tue

Camera 2

26/05/2015 9:30:15 Tue

26/05/2015 9:30:15 Tue 26/05/2015 9:30:15 Tue

Camera 1

Camera 4

2016/01/19 10:30:15 Tue

Camera2

Live View Mode

Live View is the default display mode for your NVR. Each camera connected will be displayed on-screen. You can check the status or operation of

your NVR and cameras using the status icons and Menu Bar on the Live View screen (right-click the mouse to display the Menu Bar at the bottom

of the screen). You can also access the Menu to adjust settings for Recording, Motion, Network, and to search and play previously recorded videos.

26/05/2015 9:30:15 Tue

Camera 2

26/05/2015 9:30:15 Tue

26/05/2015 9:30:15 Tue 26/05/2015 9:30:15 Tue

Camera 1

Camera 4

Camera Name

Date & Time

Status Icons

Menu - Opens the Menu.

Channel - Opens the Device List which displays

your cameras that are currently connected.

Search - Click to search and playback previ-

ously recorded videos.

Audio - Click to enable or disable live audio

playback. Only one video channel can be ena-

bled at a time.

Shutdown - Click to Lock (password must be

enabled), Shutdown or Reboot your NVR.

Click & drag a

video channel to

reposition it.

Double-click a

video channel to

view full screen.

Live View Icons

The record icon indicates that your NVR is currently re-

cording the camera’s video stream.

The audio icon indicates that the camera is selected for

live audio (click the “Audio” button on the Menu Bar to

enable).

The motion icon indicates that your NVR is detecting

motion from the camera.

This Wi-Fi icon indicates that the camera is communi-

cating wirelessly with your NVR. The icon may change

indicating the strength of the Wi-Fi signal (strong, me-

dium or weak).

The network icon indicates that the camera is physically

connected to your network via its LAN connection.

This Wi-Fi icon indicates that your NVR is running in Sta-

tion mode and is wirelessly connected to your network.

The icon may change indicating the strength of the Wi-Fi

signal (strong, medium or weak).

This indicates that the channel displaying

this message, has lost the feed from its

camera.

This Wi-Fi icon indicates that your NVR has been discon-

nected from your wireless network.

The Menu is where you control the

various actions and options that are

available on your NVR, such as ad-

justing settings for motion detection

and changing network modes. You can

also access previously recorded video

for playback and to export to a USB

storage device such as a flash drive.

To maintain system integrity, a firm-

ware upgrade can be performed when

available.

Menu Layout

By right-clicking the mouse, you can access the Menu to play back pre-

viously recorded videos, to adjust settings for motion detection and to

change system settings or upgrading the firmware.

1. Recording: This function allows you to adjust settings for the cam-

era such as camera name, encoding settings for Main Stream and Sub

Stream as well as changing the bitrate and frame rate. You can also

change the schedule for both normal and motion recording.

2. Search: This function allows you to search and play back previously

recorded videos. You’re presented with an overview of video recorded on

a particular day for a particular month for each channel on your NVR.

You can also create a backup to a USB flash drive.

3. Motion: Motion is the default recording mode for your NVR. The en-

tire view of the camera is enabled to detect motion however you can

select certain areas if you wish. The sensitivity and schedule can also

be changed according to your needs. When motion is detected, you can

enable your NVR to send you an email notification.

4. Network: This function gives you access to the various network op-

tions available including your email settings. The option to change to

Station mode can also be done here.

5. System: This function gives you access to the various system settings

such as language selection, display resolution, Daylight Saving, format-

ting the hard drive and upgrading the firmware.

6. Wizard: Click this to access the Wizard.

1 2 3

4 5 6

Camera Configuration

The camera configuration options

are available in the “Recording” and

“Motion” menus and by clicking the

“Channel” button on the Menu Bar.

You can change the camera name,

alter the encoding settings for Main

Stream and Sub Stream, change the

bitrate and frame rate and assign a

different channel number for each

camera detected. The default motion

detection area and schedule can also

be changed.

Recording: Encode

Camera No.: Select a camera that you would like to configure.

Camera Name: Give your camera a relevant name. It can be up to 16

characters in length.

OSD Display Position: Allows you to change the position of the on-screen

display. Click the “Set” button to change. Use the mouse to reposition

the camera name. Right-click the mouse then click “Save” to exit.

Record Audio: This is enabled by default. Click the checkbox if audio

recording is not required.

Encoding Parameters: Select which parameter that you would like to

configure, Main Stream or Sub Stream. By default, the SwannView Link

app and Windows software utilises the Sub Stream parameter to stream

video from your NVR to your mobile device or computer.

Resolution: The default resolution is 1080P (1920 x 1080) for Main

Stream (a lower resolution is also available). For Sub Stream the default

resolution is 640 x 360.

Max. Frame Rate(fps): For Main Stream, the default frame rate is

15fps. For Sub Stream, the default frame rate is 6fps. Increasing the

Sub Stream frame rate may improve playback quality when streaming.

Max. BitRate(Kbps): The default bitrate is 2048Kbps for Main Stream

and 160Kbps for Sub Stream. Changing the bitrate may improve play-

back quality when streaming.

• Click the “Default” button to revert back to default settings.

• Use the “Copy to” button to apply all settings to the other cameras.

• Don’t forget to click “Apply” to save settings.

Inhaltsverzeichnis

Andere Swann Sicherheitssystem Handbücher

Swann

Swann Advanced SWDVK-825504TB Bedienungsanleitung

Swann

Swann SWDVK-840004D Bedienungsanleitung

Swann

Swann Digital EagleEye ADW-400 Bedienungsanleitung

Swann

Swann PRO-580 Bedienungsanleitung

Swann

Swann HD Pro-Series Bedienungsanleitung

Swann

Swann SW245-SBD Bedienungsanleitung

Swann

Swann DVR4-2550 Bedienungsanleitung

Swann

Swann SW351-KCH Bedienungsanleitung

Swann

Swann USB 2.0 DVR Guardian SW241-UD4 Bedienungsanleitung

Swann

Swann alpha Series Bedienungsanleitung

Swann

Swann PRO-640 Bedienungsanleitung

Swann

Swann DVR Guardian SW244-UDC Bedienungsanleitung

Swann

Swann ADW-340 Bedienungsanleitung

Swann

Swann SW347-WAK Bedienungsanleitung

Swann

Swann SWDVK-840004F Bedienungsanleitung

Swann

Swann DVR4-4550 Bedienungsanleitung

Swann

Swann MDRIVE2260214E Bedienungsanleitung

Swann

Swann REDALERT SW242-WDV Bedienungsanleitung

Swann

Swann 960H Pro series Bedienungsanleitung

Swann

Swann MICROCAM II SW-P-MC2A Bedienungsanleitung

Swann

Swann SW231PC4 Bedienungsanleitung

Swann

Swann RedAlert Single Channel Digital Security... Bedienungsanleitung

Swann

Swann RedAlert SW242-WDW Bedienungsanleitung

Swann

Swann SW344-DWD Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung