Swisher L117-235001 Bedienungsanleitung

COMMERCIAL PRO

60” FAST FINISH

TRAIL MOWER

OWNER’S

MANUAL

SWISHER ACQUISITION INC.

1602 CORPORATE DRIVE., WARRENSBURG MO 640 3

PHONE 800-222-8183 FAX 660-747-8650 EMAIL CustomerCare@SwisherInc.com

MODEL NO.

FC14560CPKA

FC14560CPKA-CA

Assembly

Operation

Service and Adjustment

Repair Parts

www.swisherinc.com

20 27 REV 17-235

STARTING SERIAL #:

L117-235001

Read and follow all

Safety Precautions

and Instructions

before operating this

equipment.

IMPORTANT

ade I The

USA

of US and Global Parts

穆

LIMITED WARRANTY

The manufacturer’s warranty to the original consumer purchaser is: This product is free from

defects in materials and workmanship for the period's shown below beginning from the date

of purchase by the original consumer purchaser. We will repair or replace, at our discretion,

parts found to be defective due to materials or workmanship. This warranty is sub ect to the

following limitations and exclusions:

As req ired by CFR § 1060.120, the f el system related components, which have been

certified to this eq ipment by SAI are to be free of defects in material and workmanship for a

period of two (2) years from the date of p rchase by the original cons mer p rchaser.

1) Engine Warranty All engines utilized on our products have a separate warranty

extended to them by the individual engine manufacturer. Any

engine service warranty is the responsibility of the engine

manufacturer and in no way is Swisher or its agents responsible

for the engine warranty. The Kawasaki Engine Service Hotline is

1-877-364-6404 or email kawpow[email protected]

2) Commercial Use This prod ct has a 1yr Limited Commercial - 2 Year

Limited Consumer on All Non-Engine Parts from the date

of purchase.

3) Limitations This warranty applies only to prod cts, which have been

properly assembled, adj sted, and operated in accordance with

the instr ctions contained within this man al. This warranty

does not apply to any prod ct of Swisher that has been s bject

to alteration, mis se, ab se, improper assembly or installation,

shipping damage, or to normal wear of the prod ct.

4) Excl sions Excl ded from this warranty are normal wear, normal

adj stments, and normal maintenance.

In the event yo have a claim nder this warranty, yo m st ret rn the prod ct to an

a thorized service dealer. All transportation charges, damage, or loss inc rred d ring

transportation of parts s bmitted for replacement or repair nder this warranty shall be borne

by the p rchaser. Sho ld yo have any q estions concerning this warranty, please contact s

toll-free at 1-800-222-8183. The model n mber, serial n mber, date of p rchase, and the

name of the a thorized Swisher dealer from whom yo p rchased the mower will be needed

before any warranty claim can be processed.

THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME

PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not

allow the limitation of conseq ential damages or limitations on how long an implied warranty

may last, so the above limitations or excl sions may not apply to yo . This warranty gives

yo specific legal rights and yo may have other rights, which vary from state-to-state. This is

a limited warranty as defined by the Magn son-Moss Act of 1975.

顆掐

ɋҎ

SAFETY PRECAUTIONS

• Read the man al. Learn to operate this machine safely.

• Always disconnect the spark pl g wire and place the wire where it cannot contact the spark pl g, to prevent

accidental starting the engine when setting p, transporting, adj sting or making repairs.

• Keep all shields and g ards in place.

• Understand the speed, steering and stability of this machine. Know the positions and operations of all

controls before yo operate this machine. Check all of the controls in a safe ar

ea before starting to work with

this machine.

• Allow only responsible ad lts who are familiar with these instr ctions to operate this machine. Never allow

children to operate this machine.

• Clear the area of objects s ch as rocks, toys, wire, etc. that can be picked p and thrown by the blade.

• Be s re the area is clear of other people before mowing. Be aware of the mower discharge direction and do

not point at anyone. Stop the machine if anyone enters the mowing area. Children are often attracted to the

machine and the mowing activity. Never assume that children will remain where you last saw them.

Keep

children nder the watchf l care of another responsible ad lt.

• No riders!

• Do not p t hands or feet near or nder rotating parts. Keep clear of the discharge opening at all times.

• Do not mow in reverse. Always look down and behind before and while backing.

• T rn off the blades when not mowing. Before leaving the machine, t rn off the blades and stop the engine.

• Watch for traffic when operating near or crossing roadways.

• Do not operate the mower if it has been dropped or damaged in any manner or if the mower vibrates

excessively. Excessive vibration is an indication of damage. Repair mower as necessary.

• Dress properly. Do not operate the mower when barefoot or wearing open sandals. Wear only solid shoes

with good traction when mowing.

• Do not operate the machine while nder the infl ence of alcohol or dr gs.

• Do not operate on slopes greater than 15 degrees.

• Never tamper with safety devices. Check their proper operation reg larly.

• Stop and inspect the eq ipment if yo strike an object. Repair, if necessary, before restarting.

• Never make adj stments or repairs with the engine r nning.

This Safety Alert Symbol indicates important messages in this

manual. When you see this symbol, carefully read the message that

follows and be alert to the possibility of personal injury.

Read this manual completely. This machine can amputate hands, feet, and throw

objects. Failure to observe the following safety instructions could result in serious

injury or death.

虆 ཰

˸҇

SAFETY DECALS

Replace decals immediately if damaged. Order by part n mber from Swisher.

OD45- Warning Decal

OD11- No step Decal

OD55- Triangle Danger Decal

OD33- Speed Decal

OD29- Danger Decal

OD43- Flying Debris Decal

*Battery cover not shown

Battery Mounting Detail

A U1 battery is required

(not included). Position

battery hold down

bracket as shown.

Tighten nuts so battery

will not shift position.

REQUIRED ASSEMBLY

FRONT WHEEL CASTER ASSEMBLY

1. Remove single n t and washers from caster shaft.

2. Place one washer (NB195) on the shaft of the caster/wheel s bassembly.

3. Slide same shaft thro gh the bearing/frame with wheel towards the gro nd.

4. Place the other washer (NB195) on the shaft; it sho ld be resting on the top bearing.

5. Add thin washer (17x195).

6. Thread nyloc jam n t onto shaft.

7. Tighten n t sn ggly, making s re shaft threads enter the nyloc of the n t. Over-

tightening

of this nut will bind caster.

8. Repeat process for other front side.

9. P sh on plastic d st covers over n t and thin washer ntil it snaps into place.

REAR WHEEL ASSEMBLY

1. Remove cotter pin from axle and remove thin washer (NB149) from axle. Leave two

NB178 washers on axle.

2. If necessary (to take p space) slide extra washer (NB178) over axle, then wheel (with

valve stem o t).

3. Slide on washer (NB149) and replace cotter pin in end of axle.

4. Bend cotter pin so it will not fall o t.

5. Repeat process for other wheel.

OFFSET & CENTER TOW HITCH BAR ASSEMBLY

1. Lay o t parts according to the diagram.

2. Insert part 661A into part 662 and pin with the hitch pin (H11).

3. Insert part 20954 into part 661A. Choose from the 3 holes to set the desired hitch length.

Pin with a hitch pin (H11).

4. Part 662 slides into the front t be of the frame. Again, choose from the 3 holes to arrange

desired offset. Pin with a hitch pin (H11).

5. Eliminate step 2 for hitching from the center bracket. Only one method can be sed at a

time.

OPERATING YOUR TRAIL MOWER

INTENDED USE

This Trail Mower is designed to prod ce a q ality finish c t on lawns, golf co rses, etc. It is

not designed to clear br sh or c t saplings. Yo r Trail Mower sho ld be towed behind an

ATV, a golf cart, lawn tractor, or similar approved vehicle. It is not meant for speeds

exceeding 5 mph.

ATTACHING TRAIL MOWER TO TOW VEHICLE

• Place mower behind vehicle and back vehicle p to desired attaching position.

• When offsetting Trail Mower do so to side opposite the discharge of the tow vehicle.

• Attach tow hitch (661) to the swivel hitch with hitch pin (H11). Make certain hitch

pin goes completely thro gh each piece and is clipped to prevent accidental

separation.

• Attach red safety tether (6736) to both the towing vehicle and to the Trail Mower

toggle switch (685SP), located on the left battery side cover (17614). Its p rpose is to

man ally stop mower engine or to stop mower engine in case the two machines

become separated. (See Motor Base Detail page 14).

• It is extremely important the safety tether is secured properly to both the toggle

switch and the towing vehicle.

STARTING THE ENGINE

See engine man fact rer’s instr ctions for the type and amo nt of oil and f el sed. Trail

Mowers with electric start engines will need a battery (sold separately). Swisher recommends

sing a standard “U 1 R” lawn & garden battery.

The operation of any mower can prod ce foreign objects to be thrown into the

eyes, res lting in severe eye damage. Always wear certified safety glasses or

wide-vision safety goggles over spectacles before starting any c tting machine and

while operating s ch a machine.

The operation of any c tter prod ces so nd waves that are damaging to the

h man ear. Ear protection is recommended.

CAUTION!

Tragic accidents can occ r if the operator is not alert to the presence of

children. Children are often attracted to the machine and the mowing

activity. Never assume that children will remain where you last saw them.

IMPORTANT: This engine is not equipped with a spark arrester muffler. It is a violation of

California Public Resource Code Section 4442 to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land. Other states or federal areas may have similar laws.

ꡆ

掐

ɋ Ҏ

•

Engine m st be level to acc rately check and fill oil. Do not overfill.

• Make s re the tow vehicle parking brake is set, mower is level, and blades are disengaged.

• Check spark pl g wire, oil, and f el.

• Check all electrical connections (See Schematics).

• Make s re toggle switch is t rned “ON” and the red tether is properly attached.

• Set engine idle to “CHOKE” position.

• With feet clear of mower deck, t rn key switch to the “START” position and release when

engine begins to r n.

• Set engine idle at desired RPM.

BREAKING IN YOUR MOWER

• Set vehicle parking brake or chock wheels to prevent accidental rolling.

• Start engine properly.

• Slowly, engage blade control.

• In a safe environment, i.e. no children, allow blades to rotate and engine to idle for 5

min tes. This breaks in the belts and the engine.

• Stop mower properly.

MOWER HEIGHT ADJUSTMENT

• Adj st while mower is not r nning.

• The c tting range is approximately 1” to 5.5”. The height sho ld be meas red from the

gro nd to the blade tip witho t the engine r nning.

• Rotate height adj st crank handles (H7N) in a clockwise direction to lift the mower deck. A

co nter-clockwise direction is sed to lower the mower deck.

• Make s re the height adj stment is the same at side crank handles. For best res lts, see

“SUGGESTED PRACTICE” section. Grad ated scales are for reference only, not the

act al c tter height.

• Place crank handle in a retracted position to maintain height adj stment.

STARTING TO MOW

• Adj st the c tting height.

• Do ble check vehicle to mower attachment.

• Start mower engine properly.

• Slowly, activate the blade engage lever (18976

) by rotating it forward and left ntil the lever

locks into place.

• Caref lly mo nt tow vehicle and start mowing slowly.

STOPPING THE MOWING SESSION

• P ll safety tether to sh t toggle switch “OFF”. If the engine fails to stop or if the safety

tether has become inoperable, then se Alternative Stopping Method.

CAUTION!

SHUT OFF MOWER ENGINE AND REMOVE SPARK PLUG WIRE FROM

SPARK PLUG BEFORE MAKING ANY ADJUSTMENTS TO THE MOWER.

鑆㊠

˸҂

ALTERNATIVE STOPPING METHOD

• Bring vehicle to complete stop, sh t off engine, and set parking brake.

• Disengage blade engage lever (18976).

• Man ally sh t toggle and key switches to their “OFF” positions.

• Always remember to remove keys to avoid irresponsible sage.

TRANSPORTING MOWER

• Stop mower properly.

• Place mower deck in its highest position.

• If transporting witho t the se of a tow vehicle, then remove spark pl g wire and

place where it cannot contact the spark pl g.

SUGGESTED MOWING PRACTICES

• Operate mower engine at f ll throttle to ass re the best c tting performance and

maxim m material discharge.

• Allow wet grass to dry. Cl mps of wet grass will collect nder the mowing deck.

• Mowing sho ld be started with tow vehicle in low gear and increased only as safe

mowing conditions permit. This speed sho ld not exceed 5 mph.

•

The average lawn sho ld be c t to approximately 2.5” d ring the cool season and to

over 3” d ring the hot months.

• For a healthier lawn and better aesthetics, yo r lawn sho ld be mowed often and

after moderate growth.

• When c tting high or dense grass areas go slowly. Some areas may need to be

mowed twice. The second c t sho ld be at 90 degrees to the first, if possible.

• Mowing thick or high grass. Raise rear height crank handles to .5”-

.75” above the

other two handles.

• Creating a manicured lawn. Lower rear height crank handle to .25”-.5” below

front of deck. This allows grass blades to be c t twice. It also contin ally c ts

clippings to prod ce a m lching effect.

GENERAL TROUBLE SHOOTING

• The mower is not c tting level.

o Level deck, making s re the side crank-handles are eq al.

o Check air press re of all tires; make s re they are eq al, and to

man fact res specifications.

o Examine blades for damage, while mower engine is not r nning.

• The engine will not start.

Disengage blades, t rn toggle switch to “ON” position, check battery and all

other electrical connections, and inspect spark pl g and wire.

o Check for f el in the engine.

• Engine r ns poorly.

o See engine man al.

o Check throttle adj ster.

o Replace f el, clean f el filter and f el line.

IF PROBLEMS PERSIST HAVE A QUALIFIED MECHANIC SERVICE THE

MOWER. NEVER ATTEMPT TO MAKE AN ADJUSTMENT THAT YOU ARE

NOT SURE IS CORRECT. DOING SO CAN CAUSE OTHER PROBLEMS.

둆 ㊠

ɋ҂

MOWER MAINTENANCE

GENERAL RECOMMENDATIONS

The warranty on this Trail Mower does not cover items that have been s bjected to operator ab se or negligence.

To receive f ll val e from the warranty, operator m st maintain nit as instr cted in this man al.

Some adj stments will need to be made periodically to maintain yo r nit properly.

All adj stments in this man al sho ld be checked at least once each season.

Periodically inspect and clean excessive debris inside the battery cover (17340) and belt covers (18391

). Disconnect

spark pl g wire before cleaning.

BEFORE EACH USE

• Check engine oil level on a level s rface. Check twice to ins re an acc rate reading.

• Check condition of air filter; clean and replace as necessary.

• Check blade operation; keep blades in good condition.

• Check for loose fasteners and tighten them as needed.

AFTER EACH USE

• Keep blades sharp.

• Remove fresh grass clippings with garden hose.

• Grass clippings hardened to the nderside sho ld be scraped o t with a p tty knife.

• Keep fl ids at proper levels.

• Cover nit to prevent rain or other debris b ild p. Definitely cover the engine.

BEFORE AND/OR AFTER EACH SEASON

• Replace the spark pl g.

• Clean or replace the air filter.

• A new spark pl g and clean air filter ass re proper air-f el mixt re and help yo r engine r n better and last

longer.

• Check blades and belts for wear. Replace as necessary.

STORAGE RECOMMENDATIONS

CAUTION!

Do not store engine indoors or other poorly ventilated area. Keep engine away from gas appliances

where f mes co ld contact open flame, pilot lights, or sparks.

If engine is to be stored for 30 or more days, prepare unit as follows:

• Drain f el o tside into an approved container.

• Start engine properly and r n ntil nit is o t of f el.

• Let engine cool.

• Remove remaining gasoline from carb retor and f el tank to prevent g m deposits from forming within

the engine. G m deposits can ca se malf nction in the engine.

• Store mower with blades disengaged to prevent belts from being permanently stretched.

BLADE CARE AND SERVICE

For best res lts c tter blades m st be kept sharp. The blades can be sharpened with a few strokes of a file or

grinding wheel. Do not attempt to sharpen blades while they are on the mower. Disconnect spark plug wire before

servicing unit.

Important: Replace blades that have been damaged or deeply nicked.

Important: Check blade and spindle hardware on a regular basis to make sure nuts are tight.

Only a q alified mechanic sho ld be sed for any

adj stments, disassembly or other kind of repairs.

ꁆւ

˸ p

FRAME ASSEMBLY

GAS TANK

ASSEMBLY DETAIL

When ordering replacement parts

*USE PAINT CODE: GT=GRAY TK=BLACK

Item Qty Description Part

1 4 Nut - Nyloc 3/8-16 ZY NB182

2 1 Mount - For EPA/CARB Gas Tank 18331*

3 2 Ubolt - SQ , 3/8-16X2.437 X 3 Lg GR 5 ZY 12447

4 1 Cap, Fuel - 2.50 Gallon, Carb Sealed 18221

5 1 Bracket - Fuel Tank 18225

6 2 Bolt - Serr Flange 1/4-20 X 1 3/4 GR5 ZY 18236

7 1 Fuel Tank - 2.5 Gallon, Carb 18214

8 2 Washer - SAE Flat 1/4 ZY NB274

9 2 Nut - Nylock 1/4-20 NB180

Part Description

11782 Line - Fuel, Bulk, 1/4" Low Perm

18232 Line - Fuel, Bulk, 3/16" Low Perm

18223 Clamp - Fuel

AS021 Tie, Black 5 1/2"

Parts Not Shown

ONLY INCLUDED ON “CA” MODELS

(CALIFORNIA COMPLIANT)

Item Qty Description Part

1 4 Screw - 10-24 X 3/4 Phil Truss Head ZP 024203

2 2 Bracket - Carbon Canister, ZT 17127

3 4 Nut - 10-24 Nylon Lock 024900

4 1 Carbon Canister - 2.50 Gallon, 3/16 Line 18224

5 2 Cable Tie - Carbon Canister 18219

ITEMS 4-8 ARE PART OF

ASSEMBLY 20954

ITEM # QTY.

PART NO.

DESCRIPTION

1 1 662* Weldment - Tong e Offset Extension

2 1 661A* Weldment - Solid Stock Hitch

3 4 H11 Pin - Safety Hitch

4 2 NB622 Bolt - Serr Flange, 5/16-18X2 1/4

5 1 21152* Plate - Clevis, Top

6 1 20953* T be - Tow Hitch

7 1 21153* Plate - Clevis, Bottom

8 2 NB170 N t - Serr Flange 5/16-18

9 1 3664 Bar - Right Sway

ITEM # QTY. PART NO. DESCRIPTION

10 3 10579 B shing -Stepped Height Adj st

11 6 NB126 Pin - 1/8" X 1" Cotter

12 4 T2PB B shing - Plastic

13 3 10038 Bolt - Eye

14 1 3665 Bar - Left Sway

15 1 17600* Weldment - T60 Frame

16 4 NB178 Washer - 5/8 ID X 1 OD 10 GA

17 2 F4157WK Wheel/Tire

18 2 NB149 Washer - 5/8 ID X 1 OD 14 GA

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Swisher Rasenmäher Handbücher

Swisher

Swisher PST67522A Bedienungsanleitung

Swisher

Swisher QuadBoss QBRT10544 Bedienungsanleitung

Swisher

Swisher POL 14560 Bedienungsanleitung

Swisher

Swisher L116-245001 Bedienungsanleitung

Swisher

Swisher POL10544HD Bedienungsanleitung

Swisher

Swisher FC18560BS Bedienungsanleitung

Swisher

Swisher FC14560CL Gebrauchs- und Pflegehandbuch

Swisher

Swisher The Predator WB11524 Bedienungsanleitung

Swisher

Swisher T844CH Bedienungsanleitung

Swisher

Swisher ST67522CC Bedienungsanleitung

Swisher

Swisher FC10544BSXP Bedienungsanleitung

Swisher

Swisher ZT2460 Z-MAX Bedienungsanleitung

Swisher

Swisher T1360 Bedienungsanleitung

Swisher

Swisher RT1250E Bedienungsanleitung

Swisher

Swisher POL 14560B Bedienungsanleitung

Swisher

Swisher ZTR2760BS Bedienungsanleitung

Swisher

Swisher T1260F Bedienungsanleitung

Swisher

Swisher ZT2452 Bedienungsanleitung

Swisher

Swisher COMMERCIAL PRO Bedienungsanleitung

Swisher

Swisher Z-MAX ZT2560 Betriebsanleitung

Swisher

Swisher QUADBOSS QBRT11544 Bedienungsanleitung

Swisher

Swisher ZT2454A Bedienungsanleitung

Swisher

Swisher L118-236001 Bedienungsanleitung

Swisher

Swisher ZT2866 Bedienungsanleitung

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 60 Betriebsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Toro

Toro Groundsmaster 3505-D Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Toro

Toro 74806 Bedienungsanleitung

Stihl

Stihl RMA 443 PV Bedienungsanleitung

Yard-Man

Yard-Man 3700-0 Bedienungsanleitung