Swisher The Predator WB11524 Bedienungsanleitung

THEPREDATOR

24”ROUGHCUT

WALKBEHINDCUTTER

OWNER’S

MANUAL

MODEL NO.

Operation

Service and Adjustment

Repair Parts

Rev 05-069

1602 CORPORATE DRIVE, P.O. BOX 67, WARRENSBURG, MISSOURI 64093

PHONE (660) 747-8183 FAX (660) 747-8650

Manufacturing quality lawn care equipment since 1945 Made In The

USA

Read and follow all Safety

Rules and Instructions

before operating this

equipment.

WB11524

swisherinc.com

STARTING SERIAL #:

L205-057001

10750

Need Parts

www.SmallEngineDiscount.com

In the event you have a claim under this warranty, you must return the product to an authorized

service dealer. All transportation charges, damage, or loss incurred during transportation of parts

submitted for replacement or repair under this warranty shall be borne by the purchaser. Should you

have any questions concerning this warranty, please contact us toll-free at 1-800-222-8183. The

model number, serial number, date of purchase, and the name of the authorized Swisher dealer from

whom you purchased the mower will be needed before any warranty claim can be processed.

THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME

PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not

allow the limitation of consequential damages or limitations on how long an implied warranty may

last, so the above limitations or exclusions may not apply to you. This warranty gives you specific

legal rights and you may have other rights, which vary from state-to-state. This is a limited warranty

as defined by the Magnuson-Moss Act of 1975.

LIMITED WARRANTY

The manufacturer’s warranty to the original consumer purchaser is: This product is free from defects

in materials and workmanship for a period of (1) year from the date of purchase by the original

consumer purchaser. We will repair or replace, at our discretion, parts found to be defective due to

materials or workmanship. This warranty is subject to the following limitations and exclusions:

TABLE OF CONTENTS

WARRANTY………………....….2

INTRODUCTION………………..3

SAFETY..……………………….3-4

PRE-OPERATING..….……..……4

OPERATION.……………………….5-7

DECALS…..………….……………….8

PARTS BREAKDOWN…………….9-13

SAFE SLOPE GUIDE..………………15

1) Engine Warranty All engines utilized on our products have a separate warranty extended

to them by the individual engine manufacturer. Any engine service

difficulty is the responsibility of the engine manufacturer and in no

way is Swisher Mower Co., Inc. or its agents responsible for the engine

warranty. The Briggs & Stratton Engine Service Hot-Line is 1-800-

233-3723. The Tecumseh Engine Service Hot-Line is 1-800-558-5402.

2) Commercial Use This product is not intended for commercial use and carries no

commercial warranty.

3) Limitation This warranty applies only to products which have been properly

assembled, adjusted, and operated in accordance with the instructions

contained within this manual. This warranty does not apply to any

product of Swisher Mower Co., Inc., that has been subject to alteration,

misuse, abuse, improper assembly or installation, shipping damage, or

to normal wear of product.

4) Exclusions Excluded from this warranty are normal wear, normal adjustments, and

normal maintenance.

Need Parts

www.SmallEngineDiscount.com

SAFETY PRECAUTIONS

This Safety Alert Symbol indicates important messages in this

manual. When you see this symbol, carefully read the message that

follows and be alert to the possibility of personal injury.

Read this manual completely. This machine can amputate hands and feet, and

throw objects. Failure to observe the following safety instructions could result in

serious injury or death.

Thank you for choosing Swisher’s 24” Rough Cut Walk Behind Cutter.

Before operating your cutter, please read, understand and follow all of the safety

precautions and other instructions explained in this manual. As with all power

equipment, lawnmowers can be potentially dangerous if not properly used.

• Read the manual. Learn to operate this machine safely.

• Always disconnect the spark plug wire and place the wire where it cannot contact the

spark plug, to prevent accidental starting the engine when setting up, transporting,

adjusting or making repairs.

• Keep all shields and guards in place.

• Understand the speed, steering and stability of this machine. Know the positions and

operations of all controls before you operate this machine. Check all of the controls in

a safe area before starting to work with this machine.

• Allow only responsible adults who are familiar with these instructions to operate this

machine. Never allow children to operate this machine.

• Clear the area of objects such as rocks, toys, wire, etc. that can be picked up and

thrown by the blade.

• Be sure the area is clear of other people before mowing. Be aware of the mower

discharge direction and do not point at anyone. Stop the machine if anyone enters the

mowing area. Children are often attracted to the machine and the mowing activity.

Never assume that children will remain where you last saw them. Keep children

under the watchful care of another responsible adult.

•No riders!

• Do not put hands or feet near or under rotating parts.

• Do not mow in reverse. Always look down and behind before and during backing.

Need Parts

www.SmallEngineDiscount.com

• Turn off the blade when not mowing. Before leaving the machine, turn off the blade

and stop the engine.

• Watch for traffic when operating near or crossing roadways.

• Do not operate the mower if it has been dropped or damaged in any manner or if the

mower vibrates excessively. Excessive vibration is an indication of damage. Repair mower

as necessary.

• Dress properly. Do not operate the mower when barefoot or wearing open sandals. Wear

only solid shoes with good traction when mowing.

• Never allow operation by untrained persons.

• Do not operate the machine while under the influence of alcohol or drugs.

• Do not operate on slopes greater than 15 degrees.

• Never tamper with safety devices. Check their proper operation regularly.

• Stop and inspect the equipment if you strike an object. Repair, if necessary, before

restarting. Never make adjustments or repairs with the engine running.

• Mower blades are sharp and can cut. Wrap the blades or wear gloves, and use extra

caution when servicing them. Do not operate at too fast a rate.

• Disengage spark plug wire and place where it cannot make a connection.

• Check engine oil. All engines are filled with oil at the factory. Verify oil level and

add if necessary before starting engine. (See Engine Owner’s Manual)

• Verify fuel level and add if necessary before starting engine.

• Reconnect spark plug wire.

• (Refer to Owner’s Manual pp. 5-7) For proper operating procedures.

PRE-OPERATING INSTRUCTIONS

Need Parts

www.SmallEngineDiscount.com

The operation of any mower can produce foreign objects to be thrown into the

eyes, resulting in severe eye damage. Always wear certified safety glasses or

wide-vision safety goggles over spectacles before starting any cutting machine and

while operating such a machine.

The operation of any cutter produces sound waves that are damaging to the

human ear. Ear protection is recommended.

CAUTION!

Tragic accidents can occur if the operator is not alert to the presence of

children. Children are often attracted to the machine and the mowing

activity. Never assume that children will remain where you last saw them.

OPERATING YOUR NEW CUTTER

INTENDED USE

This is not a lawn mower. The Predator is designed for cutting overgrown brush, weeds,

and other types of organic growth. This unit is capable of clearing small saplings of 1-

1/2” in diameter or less.

PROPULSION

The Predator is self-propelled, and is controlled by a “GROUND CONTROL” lever. To

engage the drive, put the transaxle in a gear and activate the left lever. Releasing the lever

will disengage the self-propel.

Under most conditions cutting should be done in a low gear (1st or 2nd). Upper gears

should be used for conditions where weeds and brush are thinned out or not as tall. In

confined areas the machine can be pushed forwards or backwards by releasing the

“GROUND CONTROL” lever, placing the transaxle in neutral, and pushing the machine.

TRAVEL SPEED

Can be varied by choosing a higher or lower gear using the gearshift lever at the rear of

the machine or by changing the engine speed with the engine throttle. Do not adjust speed

with the blade engaged. To shift the cutter into reverse, release “GROUND CONTROL”

lever, disengage blade, and rotate the shift lever to the left. When the lever stops, lift up

the reverse lockout latch and continue to move the shift lever to the left until it stops

again. The Predator is equipped with a safety control that will kill the engine if the

blade is engaged while cutter is in the “reverse” gear.

ENGAGING BLADE

An “OPERATOR PRESENCE” lever and a “BLADE ENGAGE DRIVE” control work

together to engage the Predator’s blade. Both devices must be activated before the blade

will work. Releasing the “OPERATOR PRESENCE” lever will disengage both the blade

and the “BLADE ENGAGE DRIVE” control.

Need Parts

www.SmallEngineDiscount.com

STARTING THE ENGINE

See engine manufacturer’s recommendations for the type and amount of oil and fuel used.

Engine must be level to accurately check and fill oil. Do not overfill.

• Make sure unit is level, blade is disengaged, and transaxle in “NEUTRAL”

• Check spark plug wire, oil level, and fuel level.

• Check all electrical connections for build-up of debris.

• If needed set “CHOKE” to “CHOKE” position.

• Set engine throttle control to ½ throttle position.

• Pull rope with a single fluid motion.

• After engine has started set “CHOKE” to “RUN” position.

STOPPING

• Bring cutter to a complete stop.

• Disengage mower blade.

• Reduce engine idle speed, and allow engine to run momentarily for cooling.

• Place transaxle in the “NEUTRAL” position.

• Move engine throttle control to off position.

CUTTER HEIGHT ADJUSTMENT

• Place two 6” wooden blocks under the deck on the side being adjusted.

• Remove nuts and bolts from the side runner.

• Slide skid up or down to preferred position.

• Replace the nuts and bolts making certain they tightened securely.

• Repeat for the other side. Runners should be at the same height.

BREAKING IN YOUR CUTTER

• Start engine properly.

• Slowly, engage blade control.

• Under supervision, allow blade to rotate and engine to idle for 5 minutes.

• Disengage blade.

• Shift through each gear. While in each gear engage the “GROUND CONTROL” lever

and travel 20 yards to ensure transaxle works properly.

BEGIN CUTTING

• Make sure area is clear of all bystanders.

• Make sure that all guards, belt guides, and the spark plug wire are properly attached.

• Start engine, set engine throttle control at maximum engine idle speed for best results.

• Allow engine to run a few moments and Slowly, engage blade.

• Move transaxle into low gear and activate “GROUND CONTROL” lever.

• Turning is done by rotating the handles left or right. This machine has significant

weight and may take more effort to turn than one may expect. Turning could take

practice.

BACKING UP

• Disengage blade.

• Check behind you for safety.

• Move transaxle into “REVERSE” position.

• Activate “GROUND CONTROL” lever.

Need Parts

www.SmallEngineDiscount.com

TRANSPORTING

• Shut off engine.

• Secure in place while unit is being transported.

• Unit should be left in low gear to avoid any slight rolling.

SUGGESTED PRACTICES

• Always operate engine at full throttle when cutting to assure the best cutting

performance and proper discharge of material.

• If grass is wet, allow it to dry. Wet grass clumps will collect on the bottom of the

deck.

• Go slow when cutting dense areas. Some dense areas may need to be gone over

twice. Better results occur if the second cut is 90 degrees to the first cut.

BEFORE EACH SEASON

A new spark plug and clean air filter assure proper air-fuel mixture and help your engine run

better and last longer.

• Replace the spark plug.

• Clean or replace the air filter.

• Check blades and belts for wear.

BEFORE EACH USE

• Check engine oil level. (Do this twice to ensure an accurate reading.)

• Check condition of air filter and clean or replace if necessary.

• Check blade operation.

• Check for loose fasteners.

DAILY MAINTENANCE

Make sure all nuts and bolts are tight and cotter pins and retainer springs are secure.

Keep blades sharp. Observe all safety precautions.

BLADE CARE AND SERVICE

For best results cutter blades must be kept sharp. The blades can be sharpened with a few

strokes of a file or grinding wheel. Do Not attempt to sharpen while on the cutter.

Important: Replace blades that have been damaged or deeply nicked.

Important: Check blade and spindle hardware on a regular basis to make sure nuts are

tight.

Need Parts

www.SmallEngineDiscount.com

SAFETY AND OPERATIONAL DECALS

Replace decal immediately if damaged. Order by part number from

Swisher Mower and Machine Co. Inc.

OD39--SWISHER FLAG DECAL

OD55--DANGER DECAL OD45--WARNING DECAL

OD83--RN1234 SHIFT DECAL 10749--REVERSE LOCK DEECAL

DECALS NOT SHOWN

OD85--Predator LH Decal

OD86--Predator RH Decal OD71--New Serial # Decal

OD87--Rugged Cut 24 4SP Trans White Decal

OD99112—LARGE LOGO WHITE DECAL

Need Parts

www.SmallEngineDiscount.com

OVERALL ASSEMBLY

When ordering replacement parts

* = USE PAINT CODE:

TC=TEX.RED,S=SILVER,TK=TEX.BLACK

Item # Description Part #

1 Predator Side Channel (Left) 10677TC

2 Predator Side Channel(Right) 10676TC

3 Predator Belt Cover 10682TC

4 5/16-18 X 3/4 Serr. Flange Bolt NB596

5 TinnermanClips 5/16-18 HeavyDuty 3669

6 5/16-18 X 2 1/4 Serr. Flange Bolt GR5 ZP NB622

7 TinnermanClip 5/16-18 3706

8 5/16-18 Serr. Flange Nut NB170

SEE DETAIL

PAGE 10

SEE DETAIL

PAGE 11

SEE DETAIL

PAGE 11

SEE DETAIL

PAGE 13

SEE DETAIL

PAGE 13

SEE DETAIL

PAGE 12

Need Parts

www.SmallEngineDiscount.com

ENGINE-PULLEY ASSEMBLY

BELT

CONFIGURATION

WIRING

CONFIGURATION

11 12

Goes in Rear

Mounting Hole

NOT ACTUAL ENGINE

USED (REF. ONLY)

Item # Description Part #

1 Motor Plate 10678TC

2 5/16-18 Serr.Flange Nut NB170

3 5/16-18 X 3/4 Serr.Flange Bolt NB596

4 BeltRetentionWeldment 10767

5 Engine PulleySpacer 1.75" Long BB105S

6 1/4 X 1/2 KeyStock 4258

7 Engine Pulley- 2.5" 2411

8 1 X 1 1/2 10GA Washer NB614HT

9 1/4 X 1 KeyStock 9031

10 Engine Pulley- 4.25"OD,1 1/4 ID BB105

11 Washer, Front Wheel (Heat Trtd) TR150W

12 Washer Belleville 699

13 7/16-20 X 1 1/2 HCF GR5 ZP NYLOC NB637

14 3/8-16 X 1 1/2 HCCG NB107

15 3/8 SAE Washer NB272

16 Idler PulleyOD-2.16", ID-3/8" B27

17 3/8-16 2 WayLocking Nut NB280

18 3/8-16 X 1 GR5 ZP Bolt NB604

19 Idler Bushing 6037

20 Idler Arm 10671TK

21 1/4-20 X 3/4 GR5 ZP Bolt NB250

22 1/4-20 Serr.Flange Nut NB524

23 Spring T2SM

24 5/16-18 X 1 1/4 Serr.Flange Bolt NB253

25 TransmissionBelt-33" 690

26 Engine B&S RecoilSt W/Gas Tank N/A

27 TransmissionCable 2432

SSB

9113

When ordering replacement parts

* = USE PAINT CODE:

TC=TEX.RED,S=SILVER,TK=TEX.BLACK

10765

BROWN

2472

BROWN

6114 – BLADE PULLEY

Important: Spring

must be hooked in

Idler Arm as shown

Install Transmission Cable Item

#27 in Idler Arm before installing

Idler Arm to Motor Plate

2410

TRANSAXLE PULLEY

690 – TRANSAXLE BELT

TOP ENGINE PULLEY

CONFIGURATION

B27 – TRANSAXLE IDLER PULLEY 2411 – TOP ENGINE PULLEY

BB105 – LOWER ENGINE PULLEY

T30V – V-BELT PULLEY

B527 – BLADE IDLER PULLEY

BA50 – BLADE ENGAGEMENT BELT

BOTTOM ENGINE PULLEY CONFIGURATION

ATTACH TO

MAGNETO

NOTE: WIRES MUST PASS THROUGH ALL WIRE GUIDES POSSIBLE

Need Parts

www.SmallEngineDiscount.com

Andere Handbücher für The Predator WB11524

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Swisher Rasenmäher Handbücher

Swisher

Swisher T2066 Gebrauchs- und Pflegehandbuch

Swisher

Swisher T1360B1; T1360T; T1360H; T1360K; T13560; RK1360; T14560; T17560; T18560;... Bedienungsanleitung

Swisher

Swisher ZT2350 Bedienungsanleitung

Swisher

Swisher RT1250E Bedienungsanleitung

Swisher

Swisher WB942 Bedienungsanleitung

Swisher

Swisher WB11542F Bedienungsanleitung

Swisher

Swisher T11044, T11544, T10544BSPB, T1 Bedienungsanleitung

Swisher

Swisher Z-MAX ZT2560 Bedienungsanleitung

Swisher

Swisher ZT2452A Betriebsanleitung

Swisher

Swisher FC10544BSXP Bedienungsanleitung

Swisher

Swisher ZTR2454BS Bedienungsanleitung

Swisher

Swisher ST60022Q Bedienungsanleitung

Swisher

Swisher ZTR2454CL Bedienungsanleitung

Swisher

Swisher Trim-N-Mow Plus STS67522BS Bedienungsanleitung

Swisher

Swisher ST60022Q Bedienungsanleitung

Swisher

Swisher FC11544BSXP Bedienungsanleitung

Swisher

Swisher WBERC11524 Bedienungsanleitung

Swisher

Swisher FC14560CL Gebrauchs- und Pflegehandbuch

Swisher

Swisher ST60022Q Bedienungsanleitung

Swisher

Swisher FT1150 Bedienungsanleitung

Swisher

Swisher Predator WB80024 Bedienungsanleitung

Swisher

Swisher T1260, T1360, T1460 Bedienungsanleitung

Swisher

Swisher PREDATOR Bedienungsanleitung

Swisher

Swisher L116-336001 Bedienungsanleitung

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 60 Betriebsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Toro

Toro Groundsmaster 3505-D Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Toro

Toro 74806 Bedienungsanleitung

Stihl

Stihl RMA 443 PV Bedienungsanleitung

Yard-Man

Yard-Man 3700-0 Bedienungsanleitung