Swisher L118-236001 Bedienungsanleitung

2/22/2021

44” COUNTRY CUT

TRAIL CUTTER

OWNER’S

MANUAL

SWISHER ACQUISITION INC.

1602 CORPORATE DRIVE, WARRENSBURG, MISSOURI 640 3

PHONE (660) 747-8183 FAX (660) 747-8650

Assembly

Operation

Service and Adjustment

Repair Parts

www.swisherinc.com

MODEL NO.

STARTING SERIAL #:

L118-236001

RC11544BS

2100 REV 18-236

Read and follow all

Safety Precautions

and Instructions

before operating this

equipment.

IMPORTANT

Read and follow all

Safety Precautions

and Instructions

before operating this

equipment.

IMPORTANT

ade I The

USA

of US and Global Parts

퉀ǧ

LIMITED WARRANTY

The manufacturer s warranty to the original consumer purchaser is: This product is free from

defects in materials and workmanship for a period of one (1) year from the date of purchase

by the original consumer purchaser.

We will repair or replace, at our discretion, parts found to be defective due to materials or

workmanship. This warranty is subject to the following limitations and exclusions:

1) Engine Warranty All engines utilized on our products has a separate warranty

extended to them by the individual engine manufacturer. Any

engine service difficulty is the responsibility of the engine

manufacturer and in no way is Swisher or its agents responsible

for the engine warranty. The Briggs & Stratton Engine Service

Hot Line is 1-800-233-3723.

2) Commercial Use This product is not intended for commercial use and carries no

commercial warranty.

3) Limitations This warranty applies only to products, which have been

properly assembled, adjusted, and operated in accordance with

the instructions contained within this manual. This warranty

does not apply to any product of Swisher that has been subject

to alteration, misuse, abuse, improper assembly or installation,

shipping damage, or to normal wear of the product.

4) Exclusions Excluded from this warranty are normal wear, normal

adjustments, and normal maintenance.

In the event you have a claim under this warranty, you must return the product to an

authorized service dealer. All transportation charges, damage, or loss incurred during

transportation of parts submitted for replacement or repair under this warranty shall be borne

by the purchaser. Should you have any questions concerning this warranty, please contact us

toll-free at 1-800-222-8183. The model number, serial number, date of purchase, and the

name of the authorized Swisher dealer from whom you purchased the mower will be needed

before any warranty claim can be processed.

THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME

PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not

allow the limitation of consequential damages or limitations on how long an implied warranty

may last, so the above limitations or exclusions may not apply to you. This warranty gives

you specific legal rights and you may have other rights, which vary from state-to-state. This is

a limited warranty as defined by the Magnuson-Moss Act of 1975.

딐Ӈ

SAFETY PRECAUTIONS

This Safety Alert Symbol indicates important messages in this

manual. When you see this symbol, carefully read the message that

follows and be alert to the possibility of personal injury.

Read this manual completely. This machine can amputate hands and feet, and

throw objects. Failure to observe the following safety instructions could result in

serious injury or death.

Thank you for choosing Swisher s 44” Trail Cutter. Before operating

your cutter, please read, understand and follow all of the safety precautions

and other instructions explained in this manual. As with all power

equipment, lawn mowers and cutters can be potentially dangerous if

improperly used.

• Read the manual. Learn to operate this machine safely.

• Always disconnect the spark plug wire and place the wire where it cannot contact the

spark plug, to prevent accidental starting the engine when setting up, transporting,

adjusting or making repairs.

• Keep all shields and guards in place.

• Understand the speed, steering and stability of this machine. Know the positions and

operations of all controls before you operate this machine. Check all of the controls in

a safe area before starting to work with this machine.

• Allow only responsible adults who are familiar with these instructions to operate this

machine. Never allow children to operate this machine.

• Clear the area of objects such as rocks, toys, wire, etc. that can be picked up and

thrown by the blade.

• Be sure the area is clear of other people before mowing. Be aware of the cutters

discharge direction and do not point at anyone. Stop the machine if anyone enters the

cutting area. Children are often attracted to the machine and the mowing activity.

Never assume that children will remain where you last saw them. Keep children

under the watchful care of another responsible adult.

•No riders!

• Do not put hands or feet near or under rotating parts.

• Do not mow in reverse. Always look down and behind before and during backing.

딐Ӈ

• Turn off the blades when not cutting. Before leaving the machine, turn off the blades

and stop the engine.

• Watch for traffic when operating near or crossing roadways.

• Do not operate the cutter if it has been dropped or damaged in any manner or if the

mower vibrates excessively. Excessive vibration is an indication of damage.

Repair cutter as necessary.

• Dress properly. Do not operate the cutter when barefoot or wearing open sandals.

Wear only solid shoes with good traction when cutting.

• Never allow operation by untrained persons.

• Do not operate the machine while under the influence of alcohol or drugs.

• Do not operate on slopes greater than 15 degrees.

• Never tamper with safety devices. Check their proper operation regularly.

• Stop and inspect the equipment if you strike an object. Repair, if necessary, before

restarting. Never make adjustments or repairs with the engine running.

• Cutter blades are sharp and can cut. Wrap the blades or wear gloves, and use extra

caution when servicing them. Do not operate at too fast a rate.

• Return lever to its vertical position to disengage blades.

• The braking system is applied when the blades become disengaged. It is designed to

bring the blades to a quick stop (approximately 7 seconds). Each Trail Cutter brake

system has been set at the factory. For safety, the consumer should not alter the

braking system.

ASSEMBLY

• Insert 5/8-11 X 2½ bolt through the top of the Pivot Assembly and Top Link and secure with

5/8-11 nut. Insert 5/8-11 x 2½ bolt through the tabs on the top of the Hitch bar and Top Link and

secure with 5/8-11 nut.

• Place 2” Hitch Coupler on the end of the Hitch Bar. Align Holes with Hitch Bar and Coupler.

Fasten using (2) 3/8-11 x 3 Bolts, (4) 3/8 Washers, and (2) 3/8-11 Locknuts. Tighten nuts securely.

• The hitch can be adjusted up or down to level the deck from front to back. (See figure 2 page 11)

• Check engine oil. All engines are filled with oil at the factory. Verify oil level and

add if necessary before starting engine. (See Engine Owner s Manual)

• Verify fuel level and add if necessary before starting engine.

• Reconnect spark plug wire.

• Refer to Owner s Manual pg 5 for proper operating procedures.

Wrench/Socket

Qty. Size

(1) 1-1/8”

(1) 1-1/16”

(2) 15/16”

(2) 9/16”

Tools Required:

• Disengage spark plug wire and place where it cannot make a

connection.

•Refer to Fig. 1 pg. 11. Attach hitch assembly parts to front of

mower using 3/8-16 X 1¼ bolts and secure with 3/8-16 locknuts.

Insert 3/4-10 x 4 ½” bolt through the bottom hole of the pivot

assembly, (2) 3/4 washers, and hitch tube and secure with 3/4-10

nut. Tighten nut tight until tube is clamped tight, then back off 1/4

turn to allow tube to pivot.

딐Ӈ

OPERATING YOUR TRAIL CUTTER

The operation of any mower can produce foreign objects to be thrown into the eyes, resulting in severe eye

damage. Always wear certified safety glasses or wide-vision safety goggles over spectacles before starting

any cutting machine and while operating such a machine.

The operation of any mower produces sound waves that are damaging to the human ear. Ear protection is

recommended.

CAUTION! Tragic accidents can occur if the operator is not alert to the presence of children.

Children are often attracted to the machine and the mowing activity. Never assume that children will

remain where you last saw them.

STOPPING THE ENGINE

• Make sure the tow vehicle parking brake is set.

•Disengage cutting blades.

• Reduce engine to idle speed and allow engine to run momentarily for cooling.

• Turn the key to the off position.

INTENDED USE

The 44” Trail Cutter is designed to clear dense areas of grass and cut saplings up to 3” thick

on meadows and small estates. It is not intended to create a finish cut on lawns. Your

Trail Cutter should be towed behind an ATV, golf cart, lawn tractor or other approved

vehicle. It is not recommended for speeds exceeding 5 MPH.

ATTACHING TRAIL CUTTER TO TOW VEHICLE

• Back vehicle up to desired towing position.

•Offset the Trail Cutter to the side opposite the tow vehicle discharge (if any).

This prevents the tow vehicle from throwing grass into Trail Cutter engine.

• Using the 7365 2” ball coupler, connect the hitch to the vehicle your machine

will be towed with. Once attached, adjust the cutting height and level the

mower by rotating the adjustment rod (See figure 2 page 11).

TRANSPORTING CUTTER

• Stop Trail Cutter.

•Place Trail Cutter deck in its highest position.

• When transporting without the use of a tow vehicle, remove spark plug wire

and place it where it cannot contact the spark plug.

딐Ӈ

ENGAGING BLADES

Note: Do not attempt to start the unit with the T-handle console in the “ENGAGED” position.

• Engage blades by pulling down the T-handle lever into the horizontal position.

• Return lever to the vertical position to disengage blades. See Fig 10 pg 17.

• The braking system is applied when the blades become disengaged. It is designed to bring

the blades to a quick stop (approximately 7 seconds). Each Trail Cutter brake system has

been set at the factory the consumer should not alter any part of the brake system.

BREAKING IN YOUR CUTTER

• Set the vehicle parking brake and chock the wheels to prevent accidental rolling.

•While engine is running, engage the blade control.

• In a safe environment, (i.e. no children or pets) allow the blades to rotate and the engine to

run at full throttle for 5 minutes, breaking in the belt for longer life.

• Disengage the blades and shut off the engine.

CAUTION: SHUT OFF THE CUTTER ENGINE AND REMOVE SPARK

PLUG WIRE FROM SPARK PLUG BEFORE MAKING ANY

ADJUSTMENTS TO THE CUTTER.

STARTING THE ENGINE

See engine manufacturer’s recommendations for the type and amount of oil and fuel used.

•Make sure the tow vehicle parking brake is set, mower is level, and blades are disengaged.

Engine must be level to accurately check and fill oil. Do not overfill.

• Check spark plug wire, oil, and fuel.

• Check all electrical connections for buildup of debris.

• Set engine idle to “CHOKE” position.

• Turn key to the “RUN” position.

• Pull rope with a single fluid motion.

• Set engine idle at maximum RPM for best performance.

• Allow engine to run a few moments before engaging blades.

IMPORTANT: This engine is not equipped with a spark arrester muffler. It is a violation of California

Public Resource Code ection 4442 to use or operate the engine on any forest-covered, brush-

covered, or grass-covered land. Other states or federal areas may have similar laws.

딐Ӈ

CUTTER HEIGHT ADJUSTMENT

• There is approximately 4” of height adjustment.

•Rotate height adjust crank handle in a clockwise direction to lower the mower deck.

Rotate counterclockwise to lift the mower deck.

• Dense areas should be cut twice.

• Push handle down to lock height position.

• Adjust the top link located on the front of the hitch to level the mower after

adjusting the cutting height (See figure 2 page 11).

TOW HITCH OFFSET

• If towing with a lawn tractor, offset the rough cut mower to the opposite side of the

lawn tractor grass discharge.

• Swisher recommends if the tow vehicle is equipped with a mid-mount mower to

overlap the cut approximately 6”. This may vary depending on mowing terrain,

obstacles, and/or tow vehicle. Always keep safety the first priority.

• Always keep the tow vehicle cutter raised higher than the Trail Cutter.

STARTING TO CUT

• Adjust the cutting height.

•Double check tow vehicle to rough cut mower attachment.

• Start mower engine and set throttle to “FAST” for best cutting performance.

• Slowly engage T-handle lever. See Fig 8 pg 16.

• Carefully mount tow vehicle and start mowing at a slow travel speed.

STOPPING THE CUTTING SESSION

• Bring tow vehicle to a complete stop, set the parking brake and disengage blades.

•Turn key switch to the “OFF” position.

• Always remember to remove keys to avoid irresponsible usage.

SUGGESTED CUTTING PRACTICES

• Operate cutter engine at full throttle to assure the best cutting performance and

maximum material discharge.

• Allow wet grass to dry. Wet grass will clump and collect under the mowing deck.

• Cutter should be started with tow vehicle in low gear and increased only as safe

mowing conditions permit. Cutting speed should not exceed 5 MPH.

• Cutting conditions and the types of grass will vary from place to place. You may

find when cutting dense areas that the pressure of the wheel tracks may cause the

grass to be pushed down and not effectively mowed. If this happens you may want

to mow the area twice. Once with the cutter raised and the second cutting at the

desired height. The second cutting should be at a right angle from the previous for

best results.

Ҽ

CAUTION: DO NOT HANDLE CUTTER BLADES WITH BARE HANDS.

CARELESS OR IMPROPER HANDLING MAY RESULT IN SERIOUS

INJURY.

GENERAL RECOMMENDATIONS

The warranty on this cutter does not cover items that have been subjected to operator

abuse or negligence. To receive full value from the warranty, operator must maintain

unit as instructed in this manual.

Some adjustments will need to be made periodically to maintain your unit properly.

Refer to your engine manual for recommended fuel, oil, and service parts.

BEFORE EACH SEASON

A new spark plug and clean air filter assure proper air fuel mixture and help your engine

run better and last longer.

• Replace the spark plug.

• Clean or replace the air filter.

• Check blades and belts for wear.

BEFORE EACH USE

• Check engine oil level. Do this twice to ensure an accurate reading.

•Check condition of air filter and clean or replace if necessary.

• Check blade operation.

• Check for loose fasteners.

• Lubricate threads of adjustment rod P/N 4006. See Fig 5 pg 13.

DAILY MAINTENANCE

Make sure all nuts and bolts are tight and cotter pins and retainer springs are secure.

Keep blades sharp. Observe all safety precautions.

BLADE CARE AND SERVICE

For best results cutter blades must be kept sharp. The blades can be sharpened with a

few strokes of a file or grinding wheel. Do Not attempt to sharpen while on the cutter.

Important: Replace blades that have been damaged or deeply nicked.

Important: Check blade and spindle hardware on a regular basis to make sure

nuts are tight.

CUTTER MAINTENANCE

•Reducing the travel speed will help cut dense growth. This allows the blades the

time necessary to make its initial cut, and regain momentum to continue cutting.

The engine may stall if you are mowing too fast!

• Do not attempt to cut areas that the tow vehicle cannot maneuver through and/or

slopes that you do not feel comfortable riding.

뙠һ

The unit is not cutting level.

•Level deck. Check air pressure of all tires; make sure they are equal. See

tires for maximum inflation.

• Without the engine running, make certain blades are installed identically.

The engine will not start.

• Disengage blades, turn key switch to the “OFF” position, check all

electrical connections and inspect spark plug and wire.

• Contact engine manufacturer or qualified mechanic.

Engine runs poorly.

• See engine manual.

• Check the throttle adjuster.

• Replace fuel, check fuel filter and fuel line.

• Check spark plug and gap.

Cutter bounces excessively while towing.

• Decrease tire pressure.

• Tow at a lower speed.

IF PROBLEMS PERSIST HAVE A QUALIFIED MECHANIC SERVICE

THE CUTTER. NEVER ATTEMPT TO MAKE AN ADJUSTMENT THAT

YOU ARE NOT SURE IS CORRECT. DOING SO CAN CAUSE OTHER

PROBLEMS.

GENERAL TROUBLESHOOTING

퉀ǧ

SAFETY AND OPERATIONAL DECALS

Replace decal immediately if damaged.

OD29-DANGER DECAL

OD33-5MPH DECAL

OD36-DEFLECTOR DECAL

OD55-DANGER DECAL

OD45-WARNING DECAL

OD10-ENGAGE DECAL

OD99-OFF/RUN DECAL

OD99112 LARGE SWISHER LOGO

19976-SWISHER FLAG DECAL

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Swisher Rasenmäher Handbücher

Swisher

Swisher T11044, T11544, T10544BSPB, T1 Bedienungsanleitung

Swisher

Swisher FC11544BSXP Bedienungsanleitung

Swisher

Swisher ZTR2460BS-CA Bedienungsanleitung

Swisher

Swisher COMMERCIAL PRO Bedienungsanleitung

Swisher

Swisher QuadBoss COMMERCIAL PRO QBFC14560CP Bedienungsanleitung

Swisher

Swisher ST50022STDQ Bedienungsanleitung

Swisher

Swisher POL10544HD Bedienungsanleitung

Swisher

Swisher WB80042F Bedienungsanleitung

Swisher

Swisher ST60022Q Bedienungsanleitung

Swisher

Swisher Z-MAX ZT2560 Bedienungsanleitung

Swisher

Swisher T1360B1 Bedienungsanleitung

Swisher

Swisher QUADBOSS COMMERCIAL PRO QBFC14566CP Gebrauchs- und Pflegehandbuch

Swisher

Swisher The Predator WB11524 Bedienungsanleitung

Swisher

Swisher ZT18542 Betriebsanleitung

Swisher

Swisher ST50022STDQ Gebrauchs- und Pflegehandbuch

Swisher

Swisher RTB105441 Bedienungsanleitung

Swisher

Swisher WRC10224HC Bedienungsanleitung

Swisher

Swisher WB11542F Bedienungsanleitung

Swisher

Swisher ZT1436 Bedienungsanleitung

Swisher

Swisher WBRC11524XP Bedienungsanleitung

Swisher

Swisher T1360B1 Bedienungsanleitung

Swisher

Swisher ST60022 Bedienungsanleitung

Swisher

Swisher ZT1436B, ZT18542, ZT2250 Bedienungsanleitung

Swisher

Swisher ZT13536, ZT17542B, ZT20050 Bedienungsanleitung

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 60 Betriebsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Toro

Toro Groundsmaster 3505-D Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Toro

Toro 74806 Bedienungsanleitung

Stihl

Stihl RMA 443 PV Bedienungsanleitung

Yard-Man

Yard-Man 3700-0 Bedienungsanleitung