Swisher T11544 Bedienungsanleitung

44” FINISH CUT

TRAILMOWER

OWNER’S

MANUAL

1602 CORPORATE DRIVE, WARRENSBURG MISSOURI 64093

PHONE 660-747-8183 FAX 660-747-8650

MODEL NO.

START SERIAL # L110-323001

Manufacturing quality lawn care equipment since 1945

Assembly

Operation

Service and Adjustment

Repair Parts

Made In The

USA

Rev 10-323

Read and follow all Safety

Precautions and

Instructions before

operating this equipment.

IMPORTANT

swisherinc.com

10662

T11544

T11544EC

T11044

T10544BSPB

T12544

T1144HSP

POL11544D

POL11544DEX

T11544-CA

T12544-CA

T12544EC

LIMITED WARRANTY

The manufacturer’s warranty to the original consumer purchaser is: This product is free from

defects in materials and workmanship for a period of one (1) year from the date of purchase

by the original consumer purchaser. We will repair or replace, at our discretion, parts found to

be defective due to materials or workmanship. This warranty is subject to the following

limitations and exclusions:

1) Engine Warranty all engines utilized on our products has a separate warranty

extended to them by the individual engine manufacturer. Any

engine service difficulty is the responsibility of the engine

manufacturer and in no way is Swisher or its agents responsible

for the engine warranty. The Briggs & Stratton Engine Service

Hot-Line is 1-800-233-3723. The Tecumseh Engine Service

Hot-Line is 1-800-558-5402.

2) Commercial Use the warranty period for any product used for commercial or rental

is limited to ninety days from the date of original purchase.

3) Limitations this warranty applies only to products, which have been

properly assembled, adjusted, and operated in accordance with

the instructions contained within this manual. This warranty

does not apply to any product of Swisher, that has been subject

to alteration, misuse, abuse, improper assembly or installation,

shipping damage, or to normal wear of the product.

4) Exclusions excluded from this warranty are normal wear, normal

adjustments, and normal maintenance.

In the event you have a claim under this warranty, you must return the product to an

authorized service dealer. All transportation charges, damage, or loss incurred during

transportation of parts submitted for replacement or repair under this warranty shall be borne

by the purchaser. Should you have any questions concerning this warranty, please contact us

toll-free at 1-800-222-8183. The model number, serial number, date of purchase, and the

name of the authorized Swisher dealer from whom you purchased the mower will be needed

before any warranty claim can be processed.

THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME

PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not

allow the limitation of consequential damages or limitations on how long an implied warranty

may last, so the above limitations or exclusions may not apply to you. This warranty gives

you specific legal rights and you may have other rights, which vary from state-to-state. This is

a limited warranty as defined by the Magnuson-Moss Act of 1975.

This Safety Alert Symbol indicates important messages in this

manual. When you see this symbol, carefully read the message that

follows and be alert to the possibility of personal injury.

Read this manual completely. This machine can amputate hands, feet, and throw

objects. Failure to observe the following safety instructions could result in serious

injury or death.

SAFETY PRECAUTIONS

• Read the manual. Learn to operate this machine safely.

• Always disconnect the spark plug wire and place the wire where it cannot

contact the spark plug, to prevent accidental starting of the engine when setting

up, transporting, adjusting or making repairs.

• Keep all shields and guards in

place.

• Understand the speed, steering and stability of this machine. Know the

positions and operations of all controls before you operate this machine. Check

all of the controls in a safe area before starting to work with this machine.

• Clear the area of objects such as rocks, toys, wire, etc. that can be picked up

and thrown by the blade.

• Allow only responsible adults who are familiar with these instructions to

operate this machine. Never allow children to operate this machine.

• Be sure the area is clear of other people before mowing. Be aware of the

mower discharge direction and do not point at anyone. Stop the machine if

anyone enters the mowing area. Children are often attracted to the machine and

the mowing activity. Never assume that children will remain where you last saw

them.Keep children under the watchful care of another responsible adult.

•No riders!

• Do not put hands or feet near or under rotating parts. Keep clear of the

discharge opening at all times.

• Do not mow in reverse. Always look down and behind before and while

backing.

• Turn off the blades when not mowing. Before leaving the machine, turn off the

blades and stop the engine.

• Watch for traffic when operating near or crossing roadways.

• Do not operate the mower if it has been dropped or damaged in any manner

or if the mower vibrates excessively. Excessive vibration is an indication of

damage. Repair mower as necessary.

• Dress properly. Do not operate the mower when barefoot or wearing open

sandals. Wear only solid shoes with good traction when mowing.

• Do not operate the machine while under the influence of alcohol or drugs.

• Operate self-propelled machines up and down slopes. There is significant risk

of overturns when operating across slopes. Operate walk-behind machines across

slopes. There is a significant risk of slipping under a walk-behind machine when

operating up and down slopes. Do not operate on slopes greater than 15 degrees.

• Never tamper with safety devices. Check their proper operation regularly.

• Stop and inspect the equipment if you strike an object. Repair, if necessary,

before restarting.

• Never make adjustments or repairs with the engine running.

• Mower blades are sharp and can cut. Wrap the blades or wear gloves, and

use extra caution when servicing them.

OD36-Deflector Decal

OD45-Warning Decal

OD103-Single Point Height Adjust Decal

OD29-Danger Decal

Engine Serial #

OD11-No Step Decal

OD15-Void Warranty Decal

OD33-Speed Decal

OD55-Triangle Danger Decal

(All four deck corners)

TrailMower Serial #

SAFETY DECALS

Replace decal immediately if damaged. Order by part number from Swisher

OD99125-Medium Swisher

Logo White Decal

(Not Pictured)

OD99127-44" Deck White Decal

(Not Pictured)

OD99127-44" Deck White Decal

(Not Pictured)

OPERATING YOUR TRAILMOWER

INTENDED USE

The 44” TrailMower is designed to produce a quality finish cut on lawns, golf courses,

etc. It is not intended to clear brush or cut saplings. Your TrailMower should be

towed behind an ATV, golf cart, lawn tractor, or other approved vehicle. It is not

designed for speeds exceeding 5 MPH.

WARNING:

To avoid serious injury,

operate your mower up and down the face of slopes, NEVER across the face. DO

NOT MOW SLOPES GREATER THAN 15 DEGREES! (See attached guide for

sighting slopes.)

ATTACHING TRAILMOWER TO TOW VEHICLE

• Back vehicle up to desired towing position.

• Offset the TrailMower to the side opposite the tow vehicle discharge (if any).

This prevents the tow vehicle from throwing grass into TrailMower engine.

• Bolt swivel hitch (H10) to tow vehicle receiver. If tow vehicle has a ball hitch,

the ball must be removed before swivel hitch can be fastened.

• Attach tow hitch (4582) to the swivel hitch with hitch pin (H11). Make certain

the hitch pin goes completely through each piece and is clipped to prevent

accidental separation. (FIGURE FOUR)

• Securely attach safety tether (6736) to tow vehicle and to the TrailMower

toggle switch located on right side of the engine. The safety tether will stop the

TrailMower engine either manually or if the two should become separated. It is

very important that the safety tether is securely attached to both the toggle

switch and to the tow vehicle. (FIGURE TWO)

The operation of any mower can produce foreign objects to be thrown into the

eyes, resulting in severe eye damage. Always wear certified safety glasses or

wide-vision safety goggles over spectacles before starting any cutting machine

and while operating such a machine.

The operation of any cutter produces sound waves that are damaging to the

human ear. Ear protection is recommended.

CAUTION!

Tragic accidents can occur if the operator is not alert to the presence of

children. Children are often attracted to the machine and the mowing

activity. Never assume that children will remain where you last saw

them.

TRANSPORTING MOWER

• Stop TrailMower.

• Place TrailMower deck in its highest position.

• When transporting unattached from tow vehicle, remove spark plug wire

and place it where it cannot contact the spark plug.

• Set vehicle parking brake or chock wheels to prevent accidental rolling.

• Start engine properly.

• Slowly, engage blade control.

• In a safe environment, i.e. no children, allow blades to rotate and engine to

idle for 5 minutes. This breaks in the belts and the engine.

• Stop mower properly.

ENGAGING BLADES (without T-handle option, Standard)

The TrailMower will not start if the blade lever is in the “ENGAGED” position.

• Engage blades by rotating blade lever into the “ENGAGED” position.

• Rotate blade lever in opposite direction to disengage blade.

• The dual braking system is applied when the blades become disengaged. It is

designed to bring the blades to quick stop (approximately 7 seconds). Each

TrailMower brake system has been tested and calibrated. For safety, the

consumer should not alter the braking system.

ENGAGING BLADES (with T-handle option, for order information see detail)

The TrailMower will not start if the T-handle console is in the “ENGAGED”

position.

• Engage blades by pulling T-handle lever into its horizontal position.

• Return lever to its vertical position to disengage blades.

• The dual braking system is applied when the blades become disengaged. It

is designed to bring the blades to quick stop. Each TrailMower brake system

has been tested and calibrated. For safety, the consumer should not alter the

braking system.

STARTING THE ENGINE

See engine manufacturer’s recommendations for the type and amount of oil and fuel

used. Trail Mowers equipped with an electric start engine will need a battery (sold

separately). Swisher recommends using a standard “12N12A” battery.

• Make sure the tow vehicle parking brake is set, mower is level, and blades are

disengaged. Engine must be level to accurately check and fill oil. Do not overfill.

• Check spark plug wire, oil, and fuel.

• Check all electrical connections for build-up or debris.

• Make sure toggle switch is not turned “OFF” and safety tether is attached.

• Set engine Throttle to “Run” position (Rabbit).

•Move the “Choke” Lever to the on position. (Cold engine only)

• With feet clear of mower deck, turn key switch to the “START” position; release

when engine begins to run (12volt models). Recoil models must use pull-rope.

Pull rope with a single fluid motion.

• Set engine throttle at maximum RPM.

• Allow engine to run a few moments before engaging blades.

BREAKING IN YOUR MOWER

CAUTION!

SHUT OFF MOWER ENGINE AND REMOVE SPARK PLUG WIRE FROM

SPARK PLUG BEFORE MAKING ANY ADJUSTMENTS TO THE MOWER.

• There is approximately 1 ½” to 4 ½” of height adjustment.

• Rotate height adjust crank handle(s) in a clockwise direction to lift the mower

deck. A counter-clockwise direction is used to lower the mower deck.

• For best results, see “SUGGESTED PRACTICE” section. Graduated scales

are for reference only, not the actual cutter height.

• Bring tow vehicle to a complete stop, shut off engine, and set parking brake.

• Disengage blades.

• Manually shut toggle switch and/or key switch to their “OFF” positions.

• Always remember to remove keys to avoid irresponsible usage. (Electric

Start models only)

• Adjust the cutting height.

• Double check vehicle to mower attachment.

• Start mower engine and set throttle to “FAST” for best cutting performance.

• Slowly engage blade clutch lever.

• Carefully mount vehicle and start mowing at a slow travel speed.

• Swisher recommends if the tow vehicle is equipped with a mid-mount mower

to overlap the cut approximately 6”. This may vary depending on mowing

terrain, obstacles, and/or tow vehicle. Always keep SAFETY the first priority.

• If the tow vehicle is not equipped with a mid-mount mower, we still

recommend offsetting the mower so that the tow vehicle does not crush the

grass.

• To change the offsetting position both ball-lock pins should be removed

(Figure One). The hitches will swivel around remaining bolts. Set hitches to

desired positions and return ball-lock pins, making sure they go thru the hitch

tubing and the semi-circled hole patterned plates.

• Remove bolts from the “L” hitch (H1), (SEE FIGURE FOUR).

• Raise or lower hitch section to obtain proper front to back adjustment.

• Re-install bolts in “L” hitch securely.

MOWER HEIGHT ADJUSTMENT

• Make adjustments while TrailMower is not running.

FRONT TO BACK ADJUSTMENT

For best cutting results, the mowing deck should be raised to ¾” higher in the

rear.

• Make adjustments while TrailMower is not running.

TOW HITCH OFFSET

This TrailMower has been designed to operate offset from the center of the tow

vehicle or consecutively with another TrailMower, providing additional cutting width.

When offsetting the mower do so to the side opposite the discharge of the tow

vehicle.

STARTING TO MOW

STOPPING THE MOWING SESSION

SUGGESTED MOWING PRACTICES

• Operate mower engine at full throttle to assure the best cutting performance and

maximum material discharge.

• Allow wet grass to dry. Wet grass will clump and collect under the mowing deck.

• Mowing should be started with tow vehicle in low gear and increased only as safe

mowing conditions permit. Mowing speed should not exceed 5 MPH.

• The average lawn should be cut to approximately 2.5” during the cool season and to

over 3” during the hot months.

• For a healthier lawn and better aesthetics, your lawn should be mowed often and

after moderate growth.

• When cutting high or dense grass areas go slowly. Some areas may need to be

mowed twice. The second cut should be at 90 degrees to the first, if possible.

•Mowing thick or high grass: Raise rear of deck to ½” to ¾” above front of the

deck. See “FRONT TO BACK ADJUSTMENT”. When mowing thick or high grass,

it is recommended to cut area twice. The first at a higher setting and the second at the

desired lawn height.

•Creating a manicured lawn: Never cut more than 1/3 of the grass height in one

cutting.

GENERAL TROUBLE SHOOTING

The mower is not cutting level.

•Check air pressure of all tires; make sure they are equal. See tires for

maximum inflation.

• Make certain blades are installed identical, without the engine running.

The engine will not start.

• Disengage blades, turn toggle switch to “OFF” position, check battery and all

other electrical connections, and inspect spark plug and wire (FIGURE

THREE).

• Contact engine manufacturer or qualified mechanic.

Engine runs poorly.

• See engine manual.

• Check the throttle adjuster.

• Replace fuel, clean fuel filter and fuel line.

• Check spark plug and gap.

Mower bounces excessively while towing.

• Lower tire pressure.

• Tow at a slower speed.

IF PROBLEMS PERSIST HAVE A QUALIFIED MECHANIC SERVICE THE

MOWER. NEVER ATTEMPT TO MAKE AN ADJUSTMENT THAT YOU

ARE NOT SURE IS CORRECT. DOING SO CAN CAUSE OTHER

PROBLEMS.

MOWER MAINTENANCE

GENERAL RECOMMENDATIONS

The warranty on this TrailMower does not cover items that have been subjected to

operator abuse or negligence. To receive full value from the warranty, operator must

maintain unit as instructed in this manual.

Some adjustments will need to be made periodically to maintain your unit properly.

All adjustments in this manual should be checked at least once each season.

BEFORE EACH USE

• Check engine oil level on a level surface. (Check twice to insure an accurate

reading.)

• Check condition of air filter; clean and replace as necessary.

• Check blade operation; keep blades in good condition.

• Check for loose fasteners and tighten them as needed.

AFTER EACH USE

• Keep blades sharp.

• Remove fresh grass clippings with garden hose.

• Hardened grass clippings on underside should be scraped out with a putty

knife.

• Keep fluids at proper levels.

• Cover unit to prevent rain or other debris build-up. Definitely cover the

engine.

BEFORE AND/OR AFTER EACH SEASON

• Replace the spark plug.

• Clean or replace the air filter.

• A new spark plug and clean air filter assure proper air-fuel mixture and help

your engine run better and last longer.

• Check blades and belts for wear. Replace as necessary.

• Change the oil.

• See engine manufacturer’s recommendations for servicing.

STORAGE RECOMMENDATIONS

CAUTION! Do not store engine indoors or other poorly ventilated area. Keep

engine away from gas appliances and water heaters where fumes could contact

open flame, pilot lights, or sparks.

If engine is to be stored for 30 or more days, prepare unit as follows:

· Drain fuel outside into an approved container.

· Start engine properly and run until unit is out of fuel.

· Let engine cool.

· Remove remaining gasoline from carburetor and fuel tank to prevent gum

deposits from forming within the engine. Gum deposits can cause

malfunction in the engine.

· Store mower with blades disengaged to prevent belts from being permanently

stretched.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Swisher Rasenmäher Handbücher

Swisher

Swisher PST5022 Bedienungsanleitung

Swisher

Swisher QUADBOSS COMMERCIAL PRO QBFC14566CP Gebrauchs- und Pflegehandbuch

Swisher

Swisher RESPONSE ZTR2354KA Bedienungsanleitung

Swisher

Swisher TRAILMOWER POL14560X Bedienungsanleitung

Swisher

Swisher POL10544HD Bedienungsanleitung

Swisher

Swisher Z Series Bedienungsanleitung

Swisher

Swisher Z-MAX ZT2560 Bedienungsanleitung

Swisher

Swisher ZTR2460BS-CA Bedienungsanleitung

Swisher

Swisher L118-236001 Bedienungsanleitung

Swisher

Swisher ZT18542A Bedienungsanleitung

Swisher

Swisher POL 14560 Bedienungsanleitung

Swisher

Swisher ZT13536, ZT17542B, ZT20050 Bedienungsanleitung

Swisher

Swisher ZT2350 Bedienungsanleitung

Swisher

Swisher FC10544BSXP Bedienungsanleitung

Swisher

Swisher T11044, T11544, T10544BSPB, T1 Bedienungsanleitung

Swisher

Swisher T11044, T11544, T10544BSPB, T1 Bedienungsanleitung

Swisher

Swisher ST67522CC Bedienungsanleitung

Swisher

Swisher QUADBOSS QBFC1966 Bedienungsanleitung

Swisher

Swisher T14560A Bedienungsanleitung

Swisher

Swisher ZT1436B, ZT18542, ZT2250 Bedienungsanleitung

Swisher

Swisher AZ Series Bedienungsanleitung

Swisher

Swisher Predator WB924 Bedienungsanleitung

Swisher

Swisher WBERC11524 Bedienungsanleitung

Swisher

Swisher POL 14560 Bedienungsanleitung

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 60 Betriebsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Toro

Toro Groundsmaster 3505-D Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Toro

Toro 74806 Bedienungsanleitung

Stihl

Stihl RMA 443 PV Bedienungsanleitung

Yard-Man

Yard-Man 3700-0 Bedienungsanleitung