Sym ALA125CC Bedienungsanleitung

SYM 1. GENERAL INFORMATION/TROUBLE DIAGNOSIS

1-1

SYMBOLS AND MARKS....................1-1

GENERAL SAFETY............................1-2

SERVICE PRECAUTIONS.................1-3

SPECIFICATIONS..............................1-9

TORQUE VALUES (ENGINE)..............1-10

TORQUE VALUES (FRAME)...............1-11

TROUBLES DIAGNOSIS.....................1-12

LUBRICATION POINTS.......................1-16

SYMBOLS AND MARKS

Symbols and marks are used in this manual to indicate what and where the special service are

needed, in case supplemental information is procedures needed for these symbols and marks,

explanations will be added to the text instead of using the symbols or marks.

Warning Means that serious injury or even death may result if procedures are not

followed.

Caution Means that equipment damages may result if procedures are not followed.

Engine oil Limits to use SAE 10W-30 API SH/CD class oil. Warranty will not cover the

damage that caused by not apply with the limited engine oil.

Grease King Mate G-3 is recommended.

Locking sealant

Apply sealant, medium strength sealant should be used unless otherwise

specified.

Oil seal Apply with lubricant.

Renew Replace with a new part before installation.

Brake fluid Use recommended brake fluid DOT3 or WELLRUN brake fluid.

Special tools Special service tools.

Correct Meaning correct installation.

Wrong Meaning wrong installation.

Indication Indication of components.

Directions Indicates position and operation directions.

Components assembly directions each other.

Indicates where the bolt installation direction, --- means that bolt cross

through the component (invisibility).

1. GENERAL INFORMATION/TROUBLE DIAGNOSIS SYM

1-2

GENERAL SAFETY

Carbon monoxide

If you must run your engine, ensure the place is

well ventilated. Never run your engine in a

closed area. Run your engine in an open area, if

you have to run your engine in a closed area, be

sure to use an extractor.

Caution

Gasoline

Gasoline is a low ignition point and explosive

material. Work in a well-ventilated place, no

flame or spark should be allowed in the work

place or where gasoline is being stored.

Caution

Used engine oil

Caution

Hot components

Caution

Battery

Caution

Brake shoe

Do not use an compressed air or a dry brush to

clean components of the brake system, use a

vacuum cleaner or the equivalent to avoid

asbestos dust flying.

Caution

Brake fluid

Caution

Exhaust contains toxic gas which may cause

one to lose consciousness and even result in

death.

 Battery emits explosive gases; flame is

strictly prohibited. Keep the place well

ventilated when charging the battery.

 Battery contains sulfuric acid (electrolyte)

which can cause serious burns so be careful

do not be spray on your eyes or skin. If you

get battery acid on your skin, flush it off

immediately with water. If you get battery

acid in your eyes, flush it off immediately

with water, then go to hospital to see an

ophthalmologist.

 If you swallow it by mistake, drink a lot of

water or milk, and take some laxative such

as castor oil or vegetable oil, and then go to

see a doctor.

 Keep electrolyte beyond reach of children.

Gasoline is highly flammable, and may explode

under some conditions, keep it away from

children.

Prolonged contact with used engine oil (or

transmission oil) may cause skin cancer

although it might not be verdict. Inhaling asbestos dust may cause disorders

and cancer of the breathing system.

Spilling brake fluid on painted, plastic, or rubber

parts may cause damage to the parts. Place a

clean towel on the above-mentioned parts for

protection when servicing the brake system.

Keep brake fluid beyond reach of children.

Components of the engine and exhaust system

can become extremely hot after engine running.

They remain very hot even after the engine has

been stopped for some time. When performing

service work on these parts, wear insulated

gloves and wait until cooling off.

SYM 1. GENERAL INFORMATION/TROUBLE DIAGNOSIS

1-3

SERVICE PRECAUTIONS

 Always use with SANYANG genuine parts

and recommended oils. Using non-designed

parts for SANYANG motorcycle may damage

the motorcycle.

 Special tools are designed for remove and

install of components without damaging the

parts being worked on. Using wrong tools

may result in parts damaged.

 When servicing this motorcycle, use only

metric tools. Metric bolts, nuts, and screws

are not interchangeable with the English

system, using wrong tools and fasteners may

damage this vehicle.

 Clean the outside of the parts or the cover

before removing it from the motorcycle.

Otherwise, dirt and deposit accumulated on

the part's surface may fall into the engine,

chassis, or brake system to cause a damage.

 Wash and clean parts with high ignition point

solvent, and blow dry with compressed air.

Pay special attention to O-rings or oil seals

because most cleaning agents have an

adverse effect on them.

 Never bend or twist a control cable to prevent

stiff control and premature worn out.

 Rubber parts may become deteriorated when

old, and prone to be damaged by solvent and

oil. Check these parts before installation to

make sure that they are in good condition,

replace if necessary.

 When loosening a component which has

different sized fasteners, operate with a

diagonal pattern and work from inside out.

Loosen the small fasteners first. If the bigger

ones are loosen first, small fasteners may

receive too much stress.

 Store complex components such as

transmission parts in the proper assemble

order and tie them together with a wire for

ease of installation later.

 Note the reassemble position of the important

components before disassembling them to

ensure they will be reassembled in correct

dimensions (depth, distance or position).

 Components not to be reused should be

replaced when disassembled including

gaskets metal seal rings, O-rings, oil seals,

snap rings, and split pins.

1. GENERAL INFORMATION/TROUBLE DIAGNOSIS SYM

1-4

 The length of bolts and screws for

assemblies, cover plates or boxes is different

from one another, be sure they are correctly

installed. In case of confusion, Insert the bolt

into the hole to compare its length with other

bolts, if its length out side the hole is the

same with other bolts, it is a correct bolt.

Bolts for the same assembly should have the

same length.

 Tighten assemblies with different dimension

fasteners as follows:

 Tighten all the fasteners with fingers, then

tighten the big ones with special tool first

diagonally from inside toward outside,

important components should be tightened 2

to 3 times with appropriate increments to

avoid warp unless otherwise indicated. Bolts

and fasteners should be kept clean and dry.

Do not apply oil to the threads.

 When oil seal is installed, fill the groove with

grease, install the oil seal with the name of

the manufacturer facing outside, check the

shaft on which the oil seal is to be installed

for smoothness and for burrs that may

damage the oil seal.

 Remove residues of the old gasket or sealant

before reinstallation, grind with a grindstone if

the contact surface has any damage.

 The ends of rubber hoses (for fuel, vacuum,

or coolant) should be pushed as far as they

can go to their connections so that there is

enough room below the enlarged ends for

tightening the clamps.

 Rubber and plastic boots should be properly

reinstalled to the original correct positions as

designed.

 The tool should be pressed against two (inner

and outer) bearing races when removing a

ball bearing. Damage may result if the tool is

pressed against only one race (either inner

race or outer race). In this case, the bearing

should be replaced. To avoid damaging the

bearing, use equal force on both races.

Both of these examples can result in bearing damage.

Manufacturer's

name

Groove

Clamp

Connector

Boots

SYM 1. GENERAL INFORMATION/TROUBLE DIAGNOSIS

1-5

 Lubricate the rotation face with specified

lubricant on the lubrication points before

assembling.

 Check if positions and operation for installed

parts is in correct and properly.

 Make sure service safety each other when

conducting by two persons.

 Note that do not let parts fall down

 Before battery removal operation, it has to

remove the battery negative (-) cable firstly.

Notre tools like open-end wrench do not

contact with body to prevent from circuit short

and create spark.

 After service completed, make sure all

connection points is secured. Battery

positive (+) cable should be connected firstly.

And the two posts of battery have to be

greased after connected the cables.

 Make sure that the battery post caps are

located in properly after the battery posts had

been serviced.

 If fuse burned, it has to find out the cause

and solved it. And then replace with

specified capacity fuse.

capacity

verification

1. GENERAL INFORMATION/TROUBLE DIAGNOSIS SYM

1-6

 When separating a connector, it locker has to

be unlocked firstly. Then, conduct the

service operation.

 Do not pull the wires as removing a

connector or wires. Hold the connector

body.

 Make sure if the connector pins are bent,

extruded or loosen.

 Insert the connector completely. If there are

two lockers on two connector sides, make

sure the lockers are locked in properly.

Check if any wire loose.

 Check if the connector is covered by the twin

connector boot completely and secured

properly.

 Before terminal connection, check if the boot

is crack or the terminal is loose.

 Insert the terminal completely. Check if the

terminal is covered by the boot. Do not let

boot open facing up.

 Secure wires and wire harnesses to the

frame with respective wire bands at the

designated locations. Tighten the bands so

that only the insulated surfaces contact the

wires or wire harnesses.

 Wire band and wire harness have to be

clamped secured properly.

 Do not squeeze wires against the weld or its

clamp.

SYM 1. GENERAL INFORMATION/TROUBLE DIAGNOSIS

1-7

 Do not let the wire harness contact with

rotating, moving or vibrating components as

routing the harness.

 Keep wire harnesses far away from the hot

parts.

 Route wire harness to avoid sharp edges or

corners and also avoid the projected ends of

bolts and screws.

 Route harnesses so that they neither pull too

tight nor have excessive slack.

 Protect wires or wire harnesses with electrical

tape or tube if they contact a sharp edge or

corner. Thoroughly clean the surface where

tape is to be applied.

 Secure the rubber boot firmly as applying it

on wire harness.

 Never use wires or harnesses which

insulation has been broken. Wrap electrical

tape around the damaged parts or replace

them.

 Never clamp or squeeze the wire harness as

installing other components.

Do not touch it.

Do not extend

it too much.

Please do not clip or

squeeze the wire.

1. GENERAL INFORMATION/TROUBLE DIAGNOSIS SYM

1-8

 Do not let the wire harness been twisted as

installation.

 Wire harnesses routed along the handlebar

should not be pulled too tight or have

excessive slack, be rubbed against or

interfere with adjacent or surrounding parts in

all steering positions.

 Before operating a test instrument, operator

should read the operation manual of the

instrument. And then, conduct test in

accordance with the instruction.

 With sand paper to clean rust on connector

pins/terminals if found. And then conduct

connection operation later.

Do you know how to set the

instrument to its measurement

position and the insert locations

of its two probes?

Clean rust.

SYM 1. GENERAL INFORMATION/TROUBLE DIAGNOSIS

1-9

SPECIFICATIONS

MAKER SANYANG MODEL ALA125CC (AW12W-6)

Overall Length 1870mm Front TELESCOPIC FORK

Overall Width 698 mm

Suspen

sion

System

Rear UNIT SWING

Overall Height 1325 mm Front 110/70-12 47J

DIMENSION

Wheel Base 1325mm

Tire

Specifi

cations

Rear 120/70-12 51J

Front 41kg

Rear 68kg Front DISK (ø 190 mm)

Curb Weight

Total 109kg

Brake

System

Rear DRUM (ø 130 mm)

Passengers/

Weight Two men/110 kg Max. Speed ＞92km/h

Front 85kg

Performa

nce

Climb Ability ＞28°

Rear 134kg Primary Reduction BELT

WEIGHT

Total Weight

Total 219kg Secondary

Reduction GEAR

Type 4-STROKE ENGINE

(OHC) Clutch Auto centrifugal clutch

Installation and

arrangement Vertical, below center,

incline 80°

Deceleration

equipment

Transmission C.V.T.

Fuel Required Unleaded gasoline Speedometer 0 ~ 140 km/h

Cycle/Cooling 4-stroke/forced air

cooled Horn 93~112dB

Bore 52.4 mm Muffler Expansion & Pulse Type

Stroke 57.8 mm

Exhaust Pipe Position

and Direction Right side, and

Backward

Cylinder

Number/Arran

gement Single Cylinder Lubrication System Forced-circulation&

splashing

Displacement 124.6 cc CO <2.0 g/km

Compression

Ratio 9.6 : 1 HC <0.8 g/km

Max. HP 6.25KW/8000 rpm

Exhaust

Emission

NOx <0.15 g/km

EURO3

Max. Torque 8.33N.m /6500 rpm Air Filtration Paper filter

Ignition C.D.I.

Noise Emission < 77dB

ENGINE

Starting System Kick & electrical starter Engine Weight(dry

weight) 30kg

1. GENERAL INFORMATION/TROUBLE DIAGNOSIS SYM

1-10

TORQUE VALUES (ENGINE)

ITEM Q'TY

THREAD DIA

(mm) TORQUE

VALUE(Kg-m) REMARKS

A.C. generator fixing bolts 2 6 0.8~1.2

Pulse generator hex bolts 2 5 0.35~0.5

Gear oil filling bolt 1 8 1.0~1.4

Oil pump flat bolts 2 6 0.8~1.2

Crankcase flange bolts 2 6 0.8~1.2

Oil pump drive sprocket nut 1 6 0.8~1.2

Cylinder/cylinder head two-ends

bolts 4 8 0.7~1.1 Tighten to crankcase

Oil pump drive separator bolts 2 6 0.8~1.2

Cam holder nuts 4 8 1.8~2.2

Start clutch lock nut 1 22 9.0~10.0

Camshaft chain adjuster bolts 2 6 0.8~1.2

Cylinder head bolts 3 6 0.8~1.2

Cylinder head cover bolts 4 6 0.8~1.2

Right crankcase cover bolts 10 6 0.8~1.2

Flywheel nut 1 12 5.0~6.0

Shroud A/B tapping screws 3 5 0.8~1.2

Cooling fan bolts 4 6 0.8~1.2

Cooling fan cover 2 6 0.8~1.2

Transmission(Gear box) bolts 7 8 1.8~2.2

RR. brake arm bolt 1 6 0.8~1.2

Crankcase draining plug bolt 1 12 3.5~4.5

Drive pulley nut 1 12 5.0~6.0

Drive face nut 1 12 5.0~6.0

Start motor bolts 2 6 0.8~1.2

Left crankcase cover bolts 10 6 0.8~1.2

Carburetor nuts 2 6 0.8~1.2

A.I. fixing hex cap nuts 2 6 0.8~1.2

Valve adjustment fixing nuts 2 5 1.0~1.5 Apply oil to thread

Gear oil draining plug bolt 1 12 3.5~4.5

Camshaft chain tensioner pivot 1 6 0.8~1.2 Hex socket bolt

Spark plug 1 10 1.0~1.4

Engine oil strainer cap 1 30 1.0~2.0

Kick starter arm bolt 1 6 0.8~1.2

Exhaust pipe bolts 2 8 3.0~3.6

Exhaust pipe connecting nuts 2 6 1.0~1.4

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sym Roller Handbücher

Sym

Sym HD200 Bedienungsanleitung

Sym

Sym HD300 Bedienungsanleitung

Sym

Sym Maxsym TL TL 500 Bedienungsanleitung

Sym

Sym Symphony cargo AY05W9-EU Series Bedienungsanleitung

Sym

Sym FIDDLE 125 Bedienungsanleitung

Sym

Sym 2009 FIDDLE II 125 Bedienungsanleitung

Sym

Sym Joymax Z+ Bedienungsanleitung

Sym

Sym Jet 100 Bedienungsanleitung

Sym

Sym Tonik 50 Bedienungsanleitung

Sym

Sym XC05W2-EU Series Bedienungsanleitung

Sym

Sym GTS 250 Bedienungsanleitung

Sym

Sym GTS 250 Bedienungsanleitung

Sym

Sym Allo 50 Bedienungsanleitung

Sym

Sym CRUiSYM A Bedienungsanleitung

Sym

Sym Fiddle II 125 AW12W Bedienungsanleitung

Sym

Sym FS05W1-EU Series Bedienungsanleitung

Sym

Sym RV 250i Bedienungsanleitung

Sym

Sym Symply50 Bedienungsanleitung

Sym

Sym Orbit 125 Bedienungsanleitung

Sym

Sym JET 50 series Bedienungsanleitung

Sym

Sym ORBIT III XE05W2-EU Series Bedienungsanleitung

Sym

Sym Scooter Bedienungsanleitung

Sym

Sym Joymax Z LW12W1-EU Bedienungsanleitung

Sym

Sym Fiddle III 50 Bedienungsanleitung

Beliebte Roller Handbücher anderer Marken

TEKTRO

TEKTRO CHEETAH Bedienungsanleitung

Douglas

Douglas Vespa Sprint Installationsanleitung

PLAYTIVE

PLAYTIVE AS-2448 Bedienungsanleitung

Ebinger

Ebinger DONKEY XL Bedienungsanleitung

Flyer

Flyer Mountain Benutzerhandbuch

BackCountry eBikes

BackCountry eBikes Storm Bedienungsanleitung

equipmed

equipmed FreeRoam II Bedienungsanleitung

Yoto

Yoto Lion Bedienungsanleitung

WESTHILL BIKES

WESTHILL BIKES LINK Bedienungsanleitung

BAnff

BAnff eProdigy series Bedienungsanleitung

Winther

Winther 475 Bedienungsanleitung

Jetson

Jetson JBZL17 Bedienungsanleitung

First Choice Mobility

First Choice Mobility Roma Medical Corella S741 Bedienungsanleitung

Carrera

Carrera impel Bedienungsanleitung

Afikim

Afikim Superlight SL-3 Bedienungsanleitung

CareCo

CareCo ZOOM Bedienungsanleitung

Douglas

Douglas Vespa G.S. Bedienungsanleitung

Gazelle

Gazelle with BOSCH System Bedienungsanleitung