Symbol LS1203 Bedienungsanleitung
LS1203
QUICK REFERENCE GUIDE
2 LS1203
© 2006 SYMBOL TECHNOLOGIES, INC. All
rights reserved.
Symbol reserves the right to make changes to
any product to improve reliability, function, or
design.
Symbol does not assume any product liability
arising out of, or in connection with, the
application or use of any product, circuit, or
application described herein.
No license is granted, either expressly or by
implication, estoppel, or otherwise under any
patent right or patent, covering or relating to
any combination, system, apparatus,
machine, material, method, or process in
which Symbol products might be used. An
implied license exists only for equipment,
circuits, and subsystems contained in Symbol
products.
Symbol and the Symbol logo are registered
trademarks of Symbol Technologies, Inc.
Other product names mentioned in this
manual may be trademarks or registered
trademarks of their respective companies and
are hereby acknowledged.
Symbol Technologies, Inc.
One Symbol Plaza
Holtsville, N.Y. 11742-1300
http://www.symbol.com
Warranty
For the complete Symbol hardware product
warranty statement, go to:
http://www.symbol.com/warranty.
Patents
This product is covered by one or more
patents. For patent information go to:
http://www.symbol.com/patents.
3
Connect/Disconnect
Cable
Connect Host Interface
Keyboard Wedge Interface
RS-232 Interface
USB Interface
1
2
4 LS1203
Aim and Scan
3
012345 012345
6 LS1203
Parts of the Scanner
Scanning Modes
The scanner can operate in two modes:
•
Triggered mode - trigger button must be
pressed to emit the laser in order to
scan a bar code.
or
•
Auto-scan mode - scanner laser is in
constant on state and no trigger button
press is required to scan a bar code.
To toggle between modes, scan
TRIGGERED/AUTO-SCAN bar codes on
page 5.
For example, if the scanner is in triggered
mode, scan AUTO-SCAN MODE to switch
to auto-scan mode. If the scanner is in
auto-scan mode, scan TRIGGERED
MODE to switch to triggered mode.
NOTE When the scanner is
not used for an extended
period of time in auto-scan
mode, it enters sleep mode.
To wake the scanner, press
the trigger button.
LED
Trigger
Button
Scan
Window
7
Troubleshooting
Problem Possible
Cause
Possible
Solutions
Nothing
happens
when the
trigger button
is pressed.
No power to
the scanner. Check system
power. Ensure
power supply is
connected.
Interface or
power
cables are
loose.
Ensure all cable
connections are
secure.
Laser
comes on,
but symbol
does not
decode.
Scanner not
programmed
for correct
bar code
type.
Ensure scanner
is programmed
to read the type
of bar code
scanned. Refer
to the LS1203
Product
Reference
Guide, p/n
72E-73953-xx,
for more
information.
Bar code
symbol is
unreadable.
Check the
symbol to
ensure it is not
defaced. Try
scanning
another bar
code type.
Distance
between
scanner and
bar code is
incorrect.
Move scanner
closer to or
further from the
bar code.
Symbol is
decoded but
not
transmitted
to the host.
Scanner not
programmed
for the
correct host
type.
Scan the
appropriate
host type bar
code.
8 LS1203
Beeper Definitions
The scanner issues different beep
sequences and patterns to indicate status.
The table below defines beep sequences
that occur during both normal scanning and
while programming the scanner.
NOTE For detailed
troubleshooting, refer to the
LS1203 Product Reference
Guide, p/n 72E-73953-xx.
Beeper
Sequence
Indication
Standard Use
Low/medium/high
beep Power up.
Short high beep A bar code symbol was
decoded (if decode beeper
is enabled).
4 long low beeps A transmission error was
detected in a scanned
symbol. The data is
ignored. This occurs if a
unit is not properly
configured. Check option
setting.
5 low beeps Conversion or format
error.
Low/high/low
beep ADF transmit error.
High/high/high/
low beep RS-232 receive error.
Parameter Menu Scanning
Short high beep Correct entry scanned or
correct menu sequence
performed.
9
Low/high beep Input error, incorrect bar
code or Cancel scanned,
wrong entry, incorrect bar
code programming
sequence; remain in
program mode.
High/low beep Keyboard parameter
selected. Enter value
using bar code keypad.
High/low/high/
low beep Successful program exit
with change in the
parameter setting.
Low/high/low/
high beep Out of host parameter
storage space. Scan SET
DEFAULTS on page 86.
Code 39 Buffering
High/low beep New Code 39 data was
entered into the buffer.
3 beeps - long
high beep Code 39 buffer is full.
Low/high/low
beep The Code 39 buffer was
erased or there was an
attempt to clear or transmit
an empty buffer.
Low/high beep A successful transmission
of buffered data.
Host Specific
USB only
4 short high
beeps Scanner has not
completed initialization.
Wait several seconds and
scan again.
Scanner gives a
power-up beep
after scanning a
USB Device
Type.
Communication with the
bus must be established
before the scanner can
operate at the highest
power level.
Beeper
Sequence
Indication
10 LS1203
LED Definitions
In addition to beeper sequences, the
scanner communicates with the user using
a two-color LED display. The table below
defines LED colors that display during
scanning.
Programming Bar Codes
Descriptions
This guide includes the programming bar
codes required to set up the scanner to
work with various host interfaces. Some
frequently used programming bar codes
are also included.
For all programming bar codes and detailed
information about the scanner, go to:
http://www.symbol.com/services/manuals
The power-up
beep occurs
more than once.
The USB bus may put the
scanner in a state where
power to the scanner is
cycled on and off more
than once. This is normal
and usually happens when
the host PC cold boots.
RS-232 only
1 short high beep A <BEL> character is
received and Beep on
<BEL> is enabled.
LED Indication
Off No power is applied to the scanner,
or the scanner is on and ready to
scan.
Green A bar code was successfully
decoded.
Red A data transmission error or
scanner malfunction occurred.
Beeper
Sequence
Indication
Andere Handbücher für LS1203
3
Inhaltsverzeichnis
Sprachen:
Andere Symbol Barcode-Lesegerät Handbücher
Symbol
Symbol LS4278 Installations- und Betriebshandbuch
Symbol
Symbol LS 9208 Bedienungsanleitung
Symbol
Symbol LT 1810 Bedienungsanleitung
Symbol
Symbol MiniScan MS-804FZY Kurzanleitung zur Einrichtung
Symbol
Symbol TC70 Bedienungsanleitung
Symbol
Symbol LS 3603 Betriebsanleitung
Symbol
Symbol LS3578-FZ20005WR Bedienungsanleitung
Symbol
Symbol LS 4071 Bedienungsanleitung
Symbol
Symbol LS 4008i Bedienungsanleitung
Symbol
Symbol Cyclone M2004-I200 Bedienungsanleitung
Symbol
Symbol PDT 3100 Series Installations- und Betriebshandbuch
Symbol
Symbol LS1203 Installations- und Betriebshandbuch
Symbol
Symbol LS 4208 Bedienungsanleitung
Symbol
Symbol LS-2100U Bedienungsanleitung
Symbol
Symbol LT 1806 Installations- und Betriebshandbuch
Symbol
Symbol DS 3408 Installations- und Betriebshandbuch
Symbol
Symbol DS3578 Bedienungsanleitung
Symbol
Symbol Symbol LS3478-FZ Bedienungsanleitung
Symbol
Symbol LT 1800 Bedienungsanleitung
Symbol
Symbol LS 7708 Bedienungsanleitung
Beliebte Barcode-Lesegerät Handbücher anderer Marken
POSMicro
POSMicro Datalogic PowerScan D7100 Bedienungsanleitung
Marson
Marson MT780 Kurzanleitung zur Einrichtung
NCR
NCR RealPOS Bedienungsanleitung
Motorola
Motorola SE3300 Kurzanleitung zur Einrichtung
Element
Element P130BT Bedienungsanleitung
Motorola
Motorola Symbol LS3008 Installations- und Betriebshandbuch
