Taylor 490 Installationsanleitung

Quit

Home

Model 490

Operator Training

Extra Firm Product

Smoothie Machine

©Taylor Company 2018

Model 490 OperatorTraining
Controls Operating Procedures Troubleshooting Quiz
Quit
Home
Controls
Controls
On/Auto
Off
Wash
The center position is OFF. 
The right position is AUTO, 
which activates the beater 
motor and the refrigeration 
system. The left position is 
WASH, which activates the 
beater motor only.
Control Switch

Model 490 OperatorTraining
Controls Operating Procedures Troubleshooting Quiz
Quit
Home
Controls
Controls
On/Auto
Off
Wash
The mix level indicators are 
located on the front of the 
machine. When the MIX LOW 
indicator is flashing, the mix 
hopper has a low supply of 
mix and should be refilled as 
soon as possible. When the 
MIX OUT indicator is flashing, 
there is no mix in the hopper. 
The compressor stops running 
until the mix is replenished. 
This eliminates possible 
damage to the beater, blades, 
drive shaft and door.
Mix LevelIndicators

Model 490 OperatorTraining
Controls Operating Procedures Troubleshooting Quiz
Quit
Home
Controls
Controls
The reset button is located on 
the left side panel. The reset 
button protects the beater 
motor from an overload 
condition. If an overload 
occurs, the reset mechanism 
will trip. To properly reset the 
freezer, place the control 
switch in the OFF position. 
Press the reset button firmly. 
Place the control switch in the 
WASH position and observe 
the freezer's performance. The 
beater motor should operate 
without tripping the overload. 
Once satisfied, place the 
control switch back in the 
AUTO position.
Reset Button

Model 490 OperatorTraining
Controls Operating Procedures Troubleshooting Quiz
Quit
Home
Operating 
Procedures
Assembly
Assembly
Sanitizing
Draining
Cleaning
Priming
Disassembly
Brush Cleaning
Rinsing
Operating Procedures
Step 1
Lubricate the groove and the 
shaft portion that comes in 
contact with the bearing on 
the beater drive shaft. Slide 
the seal over the shaft and 
groove until it snaps into 
place. DO NOT lubricate the 
hex end of the drive shaft. 
Fill the inside portion of the 
seal with 1/4” more lubricant 
and evenly lubricate the flat 
side of the seal that comes 
in contact with the bearing.

Model 490 OperatorTraining
Controls Operating Procedures Troubleshooting Quiz
Quit
Home
Operating 
Procedures
Assembly
Assembly
Sanitizing
Draining
Cleaning
Priming
Disassembly
Brush Cleaning
Rinsing
Operating Procedures
Step 2
Insert the drive shaft through 
the rear shell bearing in the 
freezing cylinder and engage 
the hex end firmly into the 
gear box coupling.

Model 490 OperatorTraining
Controls Operating Procedures Troubleshooting Quiz
Quit
Home
Operating 
Procedures
Assembly
Assembly
Sanitizing
Draining
Cleaning
Priming
Disassembly
Brush Cleaning
Rinsing
Operating Procedures
Step 3
Check the scraper blades for 
any nicks or signs of wear. If 
any nicks are present, replace 
the blades. If the blades are in 
good condition, install the 
scraper blade clips on the 
scraper blades. Place the rear 
scraper blade over the rear 
holding pin on the beater 
(knife edge to the outside).
Note: To prevent costly 
damage, the hole on the 
scraper blade mustfit securely 
over the pin.

Model 490 OperatorTraining
Controls Operating Procedures Troubleshooting Quiz
Quit
Home
Operating 
Procedures
Assembly
Assembly
Sanitizing
Draining
Cleaning
Priming
Disassembly
Brush Cleaning
Rinsing
Operating Procedures
Step 4
Holding the rear blade on the 
beater, slide the assembly into 
the freezing cylinder halfway, 
tail end first. Install the front 
scraper blade over the front 
holding pin. Slide the beater 
assembly completely into the 
freezing cylinder.

Model 490 OperatorTraining
Controls Operating Procedures Troubleshooting Quiz
Quit
Home
Operating 
Procedures
Assembly
Assembly
Sanitizing
Draining
Cleaning
Priming
Disassembly
Brush Cleaning
Rinsing
Operating Procedures
Step 5
Make sure the beater 
assembly is in position over 
the drive shaft. Turn the beater 
slightly to be certain that the 
beater is properly seated. 
When in position, the beater 
will not protrude beyond the 
front of the freezing cylinder.

Model 490 OperatorTraining
Controls Operating Procedures Troubleshooting Quiz
Quit
Home
Operating 
Procedures
Assembly
Assembly
Sanitizing
Draining
Cleaning
Priming
Disassembly
Brush Cleaning
Rinsing
Operating Procedures
Step 6
Slide the two o-rings into the 
grooves on the draw valve 
and lubricate the bottom 1/2 
of the valve.