TE Connectivity 47386-4 Bedienungsanleitung
1 of 5
© 2015 TE Connectivity family of companies
All Rights Reserved
*Trademark
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.
PRODUCT INFORMATION
1-800-522-6752
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com.
Instruction Sheet
411-1050
24 APR 15 Rev A
Figure 1
1. INTRODUCTION
CERTI-CRIMP hand tools 47386-4, 47387-7, and 525690-1 are used to crimp PIDG* and PLASTI-GRIP*
terminals and splices onto a wire range size of 0.25-2.6 mm2[22-14 AWG].
2. WIRE STRIPPING AND CRIMPING PROCEDURES
1. Strip the wire to the dimension listed in Figure 2. Strip length is determined by product to be crimped
and by wire size.
2. Open crimping jaws by closing handles until the ratchet releases. See Figure 1.
NOTE
Once the ratchet is engaged, the handles cannot be opened until they are fully closed.
3. Place the terminal in the crimping jaws as shown in Figures 3A, 3B, and 3C.
4. Place the PIDG-Nylon butt splices in crimping jaws as shown in Figure 4A.
NOTE
For crimping PLASTI-GRIP butt splices, the locator has to be removed from the tool as shown in Figure 4B.
5. Close handles until the terminal or splice is held firmly in place. Do not deform the terminal or splice
barrel. Make sure the terminal barrel rests against the locator.
6. Insert the stripped wire into the barrel. To complete the crimp, close the handles until the ratchet
release mechanism releases. Handles will open automatically and the crimped item may be removed.
7. To crimp the other half of the splice, remove it and reposition the uncrimped half in the tool and
repeat.
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low
volume applications. A wide selection of powered application equipment for extended-use, production operations is available.
CERTI-CRIMP* Hand Tools
47386-4, 47387-7, and 525690-1
Wire Size Range
Stamped Here
Insulation Crimping
Adjustment Pins in
No. 3 Position
Ratchet
Color-Coded
Handles
ORIGINAL INSTRUCTIONS
411-1050
Rev A
2 of 5
TOOL
WIRE SIZE
mm2[AWG]
COLOR
DOT
CODE
PRODUCT CRIMPED
WIRE STRIPPING LENGTH
TERMINALS
SPLICES
MIN
MAX
MIN
MAX
525690-1
47386-4
0.25-1.6
[22-16]
Red
(One Dot)
PIDG and PLASTI-GRIP Terminals, Splices, and Wire Pins
5.5
[.219]
6.4
[.250]
6.3
[.250]
7.1
[.281]
0.75-1.5
[18-16]
110-Series PIDG FASTON* Receptacles
1.0-1.5
[17-16]
187- and 250-Series PIDG FASTON Receptacles and
Resilient Type PIDG Wire Pin
6.3
[.250]
7.1
[.281]
---
---
0.3-1.0
[22-17]
250-Series PIDG FASTON Receptacle, Overlapping Barrel
Type (160583-[ ])
47387-7
1.0-2.6
[16-14]
Blue
Green
(Two Dot)
PIDG and PLASTI-GRIP Terminals, Splices, and Wire Pins
5.5
[.219]
6.4
[.250]
6.3
[.250]
7.1
[.281]
3.0-3.4
[12]
187- and 250-Series PIDG FASTON receptacles and
Resilient Type PIDG Wire Pin
6.3
[.250]
7.1
[.281]
---
---
1.5-2.5
[16-14]
250-Series PIDG FASTON Receptacle, Overlapping Barrel
Type (160313-[ ])
Figure 2
Figure 3
Terminal
Splice
Wire Pin
Resilient Type Wire Pin
PIDG FASTON Receptacle
Terminal
Terminal
Splice
Splice
Wire
Strip
Length
A
B
Items Shown
with One Dot
“A” is Insulation Barrel, “B” is Wire Barrel
3A (Terminal)
3B (Wire Pin)
3C (PIDG FASTON Receptacle)
Terminal Barrel
Rests Against
Locator
Terminal Barrel
Rests Against
Locator
Locator Fits into Slot
Between Receptacle and
Wire Barrel
411-1050
Rev A
3 of 5
Figure 4
3. INSULATION CRIMP ADJUSTMENT FOR PIDG AND PLASTI-GRIP TERMINALS AND SPLICES
The insulation crimping section of the hand tool has three positions: 1-Tight, 2-Medium, and 3-Loose. Crimping
position No. 3 is for wire having a large insulation diameter; No. 2 is for medium insulation diameter; and No. 1
is for small insulation diameter.
NOTE
Always make certain that bot insulation adjustment pins are in the same position. See Figure 1.
1. Insert the insulation adjustment pins in the No. 3 position. See Figure 1.
2. Place the terminal or splice in the crimping jaws and insert the unstripped wire into only the insulation
barrel portion of the terminal or splice. See Figure 2.
3. Squeeze the handles of the tool and complete the crimping procedure.
4. Remove the crimped terminal or splice and check the insulation support as follows:
a. Bent the wire back and forth once.
b. The terminal or splice should retain the grip on the wire insulation.
c. If the wire pulls out, se the insulation adjustment pins in next tighter position (No. 2).
d. Make a test crimp and repeat adjustment as necessary until the desired insulation grip is obtained.
e. Do not use a tighter setting than required.
NOTE
PLASTI-GRIP terminals and splices feature a wire insulation support only. PIDG terminals and splices feature an insulation
grip.
4. COLOR AND DOT CODE (Figure 2)
Make sure that the terminal, splice, and tool handle colors are coded for a given wire size. The dot coding will
appear on terminals and splices when they are crimped properly in the correct hand tools.
5. MAINTENANCE AND INSPECTION PROCEDURE
5.1. Cleaning
The tool should be immersed (handles partially closed) in a reliable commercial de-greasing compound to
remove accumulated dirt, grease, and foreign matter. Make certain that the de-greasing compound does not
attach paint or plastic materials. Remove remaining de-greasing compound with a lint-free cloth. When de-
greasing compounds are not available, tool may be wiped clean with a lint-free cloth. Re-lubricate tool before
placing it back in service. See Paragraph 5.2.
4A (PIDG Butt Splice)
4B (PLASTI-GRIP Butt Splice)
Locator
Remove
Locator
Locator Fits into
Slot in Splice
Splice Should Stick Out 1-2 mm
[.040-.080 in.] Approx.
411-1050
Rev A
4 of 5
5.2. Lubrication
Lubricate all pins, pivot points, and bearing surfaces with a good grade SAE No. 20 motor as follows:
a. Tools used in daily production, lubricate daily.
b. Tools used daily (occasional), lubricate weekly.
c. Tools used weekly, lubricate monthly.
Wipe excess oil from tool, particularly from crimping area. Oil transferred from the crimping area onto certain
terminations may affect the electrical characteristics of an application.
5.3. Die Closure Inspection
Every TE Connectivity hand tool is inspected and tested for proper die (jaw) closure before being shipped from
the factory. An inspection should, however be performed periodically to measure the tool die closure.
The tool die closure inspection is accomplished using GO/NO-GO plug gages. TE neither manufactures nor
sells plug gages, however, suggested plug gage design is shown in Figure 5. The GO/NO-GO dimensions of
the plug gage are also listed in Figure 8. The following procedure is recommended for measuring the tool die
closures. Also, refer to Instruction Sheet 408-7424.
TOOL
DIE CLOSURE DIM “A”
GAGE MEMBER DIM “A”
GO
NO-GO
GO
NO-GO
525690-1
47386-4
2.76 [.109]
2.92 [.115]
2.769-2.776
[.1090-.1093]
2.918-2.921
[.1149-.1150]
47387-7
3.02 [.119]
3.17 [.125]
3.023-3.029
[.1190-.1193]
3.172-3.175
[.1249-.1250]
Figure 5
1. Remove traces of oil or dirt from tool crimping area and plug gage.
2. Remove locator assembly.
CAUTION
Do not lose spring in locator assembly.
3. Close handles of tool until crimping jaws are bottomed. Do not apply additional pressure to tool
handles.
4. With crimping jaws bottomed, use plug gage to check the die closure.
5. Hold gage in straight alignment with the tool and carefully try to insert, without forcing, the GO
element, and then the NO-GO element. See Figure 6.
6. The GO element must pass completely through the die closure.
7. The NO-GO element may enter partially, but must not pass completely through the die closure.
8. Re-install the locator assembly.
9. If the wire barrel crimping dies meet the GO/NO-GO gage conditions, the tool may be considered
dimensionally correct.
10. If you find that the tool crimping dies do not conform to the GO/NO-GO gage conditions, return the tool
to TE for repair.
Die Closure
Configuration
“A” Dim
Suggested Plug Gage Design
25 [1.0] Min (Typ)
GO Dim “A”
NO-GO Dim “A”
411-1050
Rev A
5 of 5
Figure 6
Inspection of Wire Barrel Crimping Dies with Plug Gage
“GO” Gage Must Pass Completely Through the Die Closure
“NO-GO” Gage May Enter Partially, but Must
Not Pass Completely Through the Die Closure
PRODUCT DATASHEET
is brought to you by
SOS electronic
distribution of electronic components
Click to view availability, pricing and lifecycle information.
Visit https://www.soselectronic.com/
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere TE Connectivity Elektrowerkzeuge Handbücher
TE Connectivity
TE Connectivity 2390076-1 Bedienungsanleitung
TE Connectivity
TE Connectivity 1055258-1 Bedienungsanleitung
TE Connectivity
TE Connectivity 1213819-1 Referenzhandbuch
TE Connectivity
TE Connectivity 539 666-2 Bedienungsanleitung
TE Connectivity
TE Connectivity 2390879-1 Bedienungsanleitung
TE Connectivity
TE Connectivity NanoMQS 2280687-1 Bedienungsanleitung
TE Connectivity
TE Connectivity Hand tool for AMP DUOPLUG 2.5 Bedienungsanleitung
TE Connectivity
TE Connectivity 539744-2 Bedienungsanleitung
TE Connectivity
TE Connectivity PRO- CRIMPER III Bedienungsanleitung
TE Connectivity
TE Connectivity 59981-1 Bedienungsanleitung
TE Connectivity
TE Connectivity 2393336-1 Bedienungsanleitung
TE Connectivity
TE Connectivity 46447 Bedienungsanleitung
TE Connectivity
TE Connectivity HT40 Bedienungsanleitung
TE Connectivity
TE Connectivity SOLARLOK PN 1-1579004-1 Bedienungsanleitung
TE Connectivity
TE Connectivity PRO-CRIMPER III Bedienungsanleitung
TE Connectivity
TE Connectivity ERGOCRIMP Bedienungsanleitung
TE Connectivity
TE Connectivity CAPI-6T Bedienungsanleitung
TE Connectivity
TE Connectivity 2389862-1 Bedienungsanleitung
TE Connectivity
TE Connectivity 2430768-1 Bedienungsanleitung
TE Connectivity
TE Connectivity 2363758-1 Bedienungsanleitung
