Tektronix 80E07 Bedienungsanleitung

User Manual

80E07, 80E08, 80E09, and 80E10

Electrical Sampling Remote Modules

071-2038-01

This document applies to firmware version 2.5X

and above.

www.tektronix.com

suppliers, and are protected by national copyright laws and international treaty provisions.

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes

that in all previously published material. Specifications and price change privileges reserved.

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

Contacting Tektronix

Tektronix, Inc.

14200 SW Karl Braun Drive

P.O. Box 500

Beaverton, OR 97077

USA

For product information, sales, service, and technical support:

HIn North America, call 1-800-833-9200.

HWorldwide, visit www.tektronix.com to find contacts in your area.

Warranty 2

Tektronix warrants that this product will be free from defects in materials and workmanship for a period of one (1)

year from the date of shipment. If any such product proves defective during this warranty period, Tektronix, at its

option, either will repair the defective product without charge for parts and labor, or will provide a replacement in

exchange for the defective product. Parts, modules and replacement products used by Tektronix for warranty work

may be new or reconditioned to like new performance. All replaced parts, modules and products become the

property of Tektronix.

In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration

of the warranty period and make suitable arrangements for the performance of service. Customer shall be

responsible for packaging and shipping the defective product to the service center designated by Tektronix, with

shipping charges prepaid. Tektronix shall pay for the return of the product to Customer if the shipment is to a

location within the country in which the Tektronix service center is located. Customer shall be responsible for

paying all shipping charges, duties, taxes, and any other charges for products returned to any other locations.

This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate

maintenance and care. Tektronix shall not be obligated to furnish service under this warranty a) to repair damage

resulting from attempts by personnel other than Tektronix representatives to install, repair or service the product;

b) to repair damage resulting from improper use or connection to incompatible equipment; c) to repair any

damage or malfunction caused by the use of non-Tektronix supplies; or d) to service a product that has been

modified or integrated with other products when the effect of such modification or integration increases the time

or difficulty of servicing the product.

THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THE PRODUCT IN LIEU OF ANY

OTHER WARRANTIES, EXPRESS OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY

IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

TEKTRONIX’ RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND

EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY.

TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL,

OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS

ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.

80E07, 80E08, 80E09, and 80E10 User Manual i

Table of Contents

General Safety Summary v...................................

Environmental Considerations vii...............................

Preface ix...................................................

Manual Structure ix................................................

Related Manuals x.................................................

Getting Started 1............................................

Product Description 2..............................................

Accessories and Options 4...........................................

Standard Accessories 4..........................................

Optional Accessories 4..........................................

Options 5.....................................................

Installation 6.....................................................

Electrostatic Discharge 8........................................

Static Controlled Workstation 9...................................

Compensation 9...............................................

Operating Basics 11..........................................

Usage 11.........................................................

Controls 12........................................................

Signal Connector 12.............................................

Channel Selection 13............................................

TekProbe Connector 13..........................................

TDR On Indicator 13............................................

System Interaction 13...............................................

Commands From the Main Instrument Front Panel 14......................

Programmer Interface Commands 15...................................

User Adjustments 15................................................

Cleaning 16.......................................................

Reference 17.................................................

Taking TDR Measurements 17........................................

TDR Measurements Background 28....................................

Finding the Velocity of Propagation and Locating Mismatches 31.........

TDR Measurement Units 31.......................................

Making Accurate TDR Measurements 33............................

Taking Differential and Common-Mode TDR Measurements 33.............

Connector and Adapter Care Requirements 41...........................

Visual Inspection 41.............................................

Cleaning Connectors 42..........................................

Assembly and Torquing 44........................................

Detecting Damaged Inputs 46.........................................

EOS (Electrical Overstress) Prevention 46...............................

Specifications 49.............................................

Glossary 55.................................................

Index 57....................................................

Table of Contents

ii 80E07, 80E08, 80E09, and 80E10 User Manual

List of Figures

Figure 1: Sampling main module and remote module,

80E10 shown 2..........................................

Figure 2: Sampling module block diagram 3.....................

Figure 3: Sampling module compartments 6.....................

Figure 4: Guide rails 7.......................................

Figure 5: Sampling module, 80E10 shown 12.....................

Figure 6: Vertical Setup dialog box 14...........................

Figure 7: TDR Setup dialog box 15..............................

Figure 8: Simplified schematic diagram of step

generator - positive polarity 18..............................

Figure 9: Step generator with a shorted output 19.................

Figure 10: Step generation with a 50 Ωload 19....................

Figure 11: Step generation with an open circuit 19.................

Figure 12: TDR displays for typical loads 21......................

Figure 13: Microstrip discontinuities 28..........................

Figure 14: TDR waveform of microstrip in Figure 13 29............

Figure 15: TDR step and reflection (short) 30.....................

Figure 16: TDR step and reflection (50 Ωline terminated

in 75 Ω)32...............................................

Figure 17: TDR step of undamaged sampling module 46............

Figure 18: First example of EOS error 48........................

Figure 19: Second example of EOS error showing

cumulative effect 48.......................................

Table of Contents

80E07, 80E08, 80E09, and 80E10 User Manual iii

List of Tables

Table 1: Sampling module features 3...........................

Table 2: Standard accessories 4...............................

Table 3: Optional accessories 4................................

Table 4: Torque wrench information 45.........................

Table 5: Electrical sampling modules -- Signal acquisition 49.......

Table 6: Electrical sampling module -- TDR system

(80E08 and 80E10) 52.....................................

Table 7: Electrical sampling modules -- Timebase system 53........

Table 8: Electrical sampling modules -- Mechanical 53.............

Table of Contents

iv 80E07, 80E08, 80E09, and 80E10 User Manual

80E07, 80E08, 80E09, and 80E10 User Manual v

General Safety Summary

Review the following safety precautions to avoid injury and prevent damage to

this product or any products connected to it.

To avoid potential hazards, use this product only as specified.

Only qualified personnel should perform service procedures.

While using this product, you may need to access other parts of a larger system.

Read the safety sections of the other component manuals for warnings and

cautions related to operating the system.

Connect and Disconnect Properly. Do not connect or disconnect probes or test

leads while they are connected to a voltage source.

Ground the Product. This product is indirectly grounded through the grounding

conductor of the mainframe power cord. To avoid electric shock, the grounding

conductor must be connected to earth ground. Before making connections to the

input or output terminals of the product, ensure that the product is properly

grounded.

Observe All Terminal Ratings. To avoid fire or shock hazard, observe all ratings

and markings on the product. Consult the product manual for further ratings

information before making connections to the product.

Do not apply a potential to any terminal, including the common terminal, that

exceeds the maximum rating of that terminal.

Do Not Operate Without Covers. Do not operate this product with covers or panels

removed.

Do Not Operate With Suspected Failures. If you suspect there is damage to this

product, have it inspected by qualified service personnel.

Avoid Exposed Circuitry. Do not touch exposed connections and components

when power is present.

Wear Eye Protection. Wear eye protection if exposure to high-intensity rays or

laser radiation exists.

Do Not Operate in Wet/Damp Conditions.

Do Not Operate in an Explosive Atmosphere.

Keep Product Surfaces Clean and Dry.

ToAvoidFireor

Personal Injury

General Safety Summary

vi 80E07, 80E08, 80E09, and 80E10 User Manual

These terms may appear in this manual:

WARNING. Warning statements identify conditions or practices that could result

in injury or loss of life.

CAUTION. Caution statements identify conditions or practices that could result in

damage to this product or other property.

These terms may appear on the product:

HDANGER indicates an injury hazard immediately accessible as you read the

marking.

HWARNING indicates an injury hazard not immediately accessible as you

read the marking.

HCAUTION indicates a hazard to property including the product.

The following symbol(s) may appear on the product:

CAUTION

Refer to Manual

WARNING

High Voltage

Protective Ground

(Earth) Terminal

Terms in this Manual

Symbols and Terms

on the Product

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Tektronix Steuereinheit Handbücher

Tektronix

Tektronix TM 506A Bedienungsanleitung

Tektronix

Tektronix TDS3TRG Bedienungsanleitung

Tektronix

Tektronix 80A05 Bedienungsanleitung

Tektronix

Tektronix TM 515 Bedienungsanleitung

Tektronix

Tektronix VX4240 Bedienungsanleitung

Tektronix

Tektronix TM 501 Bedienungsanleitung

Tektronix

Tektronix 7A21N Bedienungsanleitung

Tektronix

Tektronix TDS3FFT Bedienungsanleitung

Tektronix

Tektronix Keithley 7706 Bedienungsanleitung

Tektronix

Tektronix KEITHLEY 7700 Bedienungsanleitung

Tektronix

Tektronix TM 5006 Bedienungsanleitung

Tektronix

Tektronix L3 Bedienungsanleitung

Tektronix

Tektronix TLA7PG2 Bedienungsanleitung

Tektronix

Tektronix TDS3TMT Bedienungsanleitung

Tektronix

Tektronix TM 5003 Bedienungsanleitung

Tektronix

Tektronix TM 504 Bedienungsanleitung

Tektronix

Tektronix 73A-851 Bedienungsanleitung

Tektronix

Tektronix 80C14 Bedienungsanleitung

Tektronix

Tektronix TM 501 Bedienungsanleitung

Tektronix

Tektronix ECO422D Gebrauchs- und Pflegehandbuch

Tektronix

Tektronix VX4730 Bedienungsanleitung

Tektronix

Tektronix 80C00 Bedienungsanleitung

Tektronix

Tektronix VX4286 Bedienungsanleitung

Tektronix

Tektronix 80C12B Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung