Teldat C+ Series Bedienungsanleitung

Teldat C+ Router Family

Teldat-Dm 353-I

Teldat S.A. Manual

Teldat C+ Router Family 1

Legal Notice

Warranty

This publication is subject to change.

Teldat S.A. offers no warranty whatsoever for information contained in this manual.

Teldat S.A. is not liable for any direct, indirect, collateral, consequential or any other damage connected to the deliv-

ery, supply or use of this manual.

Manual Teldat S.A.

2Teldat C+ Router Family

Table of Contents

I ImportantInformation................................ 1

Chapter1 InstallingtheRouter ................................ 2

1.1 Introduction...................................... 2

1.1.1 Recycling and the Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1.2 Connections...................................... 3

1.2.1 PowerSourceConnection................................ 4

1.2.2 DataConnections.................................... 5

1.3 MeaningoftheLEDs................................. 11

1.4 Programming the microswitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

1.4.1 Procedure to ignore the configuration, or establish the default configuration . . . . . . . . . 13

Chapter2 Appendix..................................... 15

2.1 Troubleshooting................................... 15

2.2 Softwareupdating .................................. 16

2.3 Connectors ..................................... 16

2.3.1 LANConnector.................................... 16

2.3.2 DSLConnector.................................... 16

2.3.3 ISDNConnector................................... 17

2.3.4 ANTConnector.................................... 17

2.3.5 ConfigurationConnector................................ 17

2.4 TechnicalSpecifications................................ 17

2.5 Translated safety warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Teldat S.A. Table of Contents

Teldat C+ Router Family i

Table of Contents Teldat S.A.

ii Teldat C+ Router Family

I Important Information

Note

The manufacturer reserves the right to make changes and improvements in the appropriate features in

either software or hardware of this product, modifying the specifications of this manual without prior no-

tice.

The images showing the front and back panels of the device are for information purposes only. Some

small modification may exist in the actual device.

The equipment is intended to be installed by Service Personnel and only handled by qualified person-

nel. If not, the device may be damaged and malfunction.

This device contains elements that are sensitive to electrostatic surges and shocks. Therefore, it is es-

sential when handling the equipment that an antistatic wriststrap is connected to the device chassis and

that this is placed on an antistatic mat. Furthermore, it is crucial to avoid any kind of contact between

the device components and necklaces, bracelets, rings, ties etc.

Teldat S.A. Important Information

Teldat C+ Router Family 1

Chapter 1 Installing the Router

1.1 Introduction

The Teldat C+ is a general-purpose IP router, suitable for a wide range of applications (personal, SOHO/SME and

corporate environments). It adapts perfectly to plenty of IP scenarios, providing simultaneous access to Internet for

private LAN users and accommodating teleprocess networks and SNA support.

The Teldat C+ covers the access needs for ADSL and ADS2+ (both over PSTN and ISDN). For local area net-

works (LANs), the routers can incorporate Switch LAN Ethernet and Wireless LAN MINI-PCI Module.

This manual is the installation and device connection guide.

Fig. 1: Teldat C1+: External aspect

Fig. 2: Teldat C8+ /C9+ external power: External aspect

Fig. 3: Teldat C8+ /C9+ internal power: External aspect

1.1.1 Recycling and the Environment

Please do not, under any circumstances, throw away any Teldat C+ routers with normal domestic waste. Ask your

local town hall for information on how to correctly dispose of them in order to protect the environment against e-

waste. Always respect the current laws regarding waste material. Anyone found violating the environmental laws will

be subject to fines and any additional steps established by law.

All the packing materials i.e. the cardboard box, plastic and any other packaging, together with the pieces making up

aTeldat C+ , must be recycled complying with the current active laws regarding recycling materials.

The symbol shown below with a cross over the rubbish container can be seen on the device. This means that, when

a device reaches the end of its life, it must be taken to the official recycling/disposal centers where it must be dis-

posed of in an environmentally responsible manner and separately from normal domestic waste.

1 Installing the Router Teldat S.A.

2Teldat C+ Router Family

1.2 Connections

Note

BEFORE INSTALLING THE ROUTER, PLEASE READ THE FOLLOWING INSTRUCTIONS CARE-

FULLY

Workplace Conditions. Main Characteristics

• Excessive cold and heat should be avoided, as should humidity and dust.

• Avoid direct exposure to sunlight and any other heat sources. Do not place the device between papers, magazines

or other items that could hinder natural air circulation.

• Do not place the device near strong electromagnetic fields such as those produced by speakers, motors, etc.

• Avoid knocks and/or strong vibrations during operation, storage and transport

Warning

The electric current in power cables, telephone lines and communication cables is dangerous.

To prevent electric shocks, before installing, handling or opening the equipment covers, con-

nect and disconnect the cables following the steps set forth in the following section.

To Connect To Disconnect

Turn the device’s power supply OFF. Turn the switch OFF.

Check the power supply is not connected to the mains or

to the device.

Disconnect the power supply (in devices with an external

power supply) or disconnect the device from the mains.

Connect all data cables. Disconnect the power supply from the device. (This only

refers to devices with an external power supply).

Connect the power supply to the device. (This only refers

to devices with an external power supply).

Disconnect the data cables.

Connect the power supply (in devices with an external

power supply) or connect the device to the mains.

Turn the switch ON.

Note

Some devices, such as the C1+, and the new C8+ and C9+ models, have an internal power supply

source. Consequently, the above steps are redundant.

Teldat S.A. 1 Installing the Router

Teldat C+ Router Family 3

1.2.1 Power Source Connection

Some of the Teldat C+ models are powered with an external AC/DC source.

To avoid electric shocks, residual current circulation and any other unwanted effects that may disrupt communica-

tion, the following is recommended:

Warning

All interconnected communication devices should be plugged to THE SAME GROUNDED POWER

OUTLET, which should, at the same time, be of good quality (lower than 10 ohms).

Whether the workplace is provided with an uninterrupted power supply system (UPS), regulated supply,

or it is independent from the rest (such as lighting, etc.), it is highly recommended that all data devices

should be connected to the same power source. This will avoid operating and premature aging prob-

lems of drivers and other components.

1.2.1.1 Devices with external power supply

Fig. 4: Teldat C8+ power connection with an external source

Fig. 5: Teldat C9+ power connection with an external source

To connect the power source to the device, follow the steps listed in the previous table: ensure the switch is OFF (0)

and the power supply is NOT connected to the main electricity supply; find the POWER plug (located on the rear

panel of the device) and plug it into the power source. Both the connector and the receptacle are designed to ensure

their proper installation.

For subsequent power source connections to the main electricity supply, use the grounded cable provided for this

purpose.

1.2.1.2 Devices with internal power supply sources

To connect the power source to the device, check that the power switch is in the OFF position (0) and the device is

NOT connected to the mains, find the power connector (located on the rear of the device) and plug it into the groun-

ded power cable (the shape of the connector prevents incorrect insertion).

1 Installing the Router Teldat S.A.

4Teldat C+ Router Family

Fig. 6: Teldat C1+ power connection with an internal source

Fig. 7: Teldat C8+ power connection with an internal source

Fig. 8: Teldat C9+ power connection with an internal source

1.2.2 Data Connections

The Teldat C+ is equipped with the following connectors (although some of these may not be available depending on

the model):

SWITCH:

The Teldat C+ incorporates a 4 or 8 port Switch or 2 x 8 (i.e. total of 16 ports) 10/100BaseT with automatic MDI/

MDIX for local area network (LAN) connection: this has a 100 LED indicating connection at 100 Mbps, and a 10 LED

indicating connection at 10 Mbps.

Please pay close careful attention to the labelling to avoid confusing the switch with other port types.

The following are available, depending on the model:

Fig. 9: Teldat C1+ device: 4 port LAN switch

Fig. 10: Teldat C8+ (external source) device: 8 port LAN switch

Fig. 11: Teldat C8+ (internal source) device: 8 port LAN switch

Fig. 12: Teldat C9+ (external source) device: 8 port 2 switch

Fig. 13: Teldat C9+ (internal source) device: 8 port 2 switch

Teldat S.A. 1 Installing the Router

Teldat C+ Router Family 5

DSL:

ADSL and ADSL2+ interface (both over PSTN and ISDN).

Fig. 14: Teldat C1+ model: ADSL connectors

Fig. 15: Teldat C8+ model (external source): ADSL connector

Fig. 16: Teldat C8+ model (internal source): ADSL connector

Fig. 17: Teldat C9+ model (external source): ADSL connector

Fig. 18: Teldat C9+ model (internal source): ADSL connector

ISDN:

Basic ISDN 2B+D interface: this has a trigger mechanism, which in some devices is a switch (TERM), and in others,

consists of 2 ports (to introduce the S bus termination load).

You need a software license for operating purposes.

Fig. 19: Teldat C1+ model: ISDN connector

Fig. 20: Teldat C8+ model (external source): ISDN connector and TERM pushbutton

Fig. 21: Teldat C8+ model (internal source): ISDN connector and TERM pushbutton

1 Installing the Router Teldat S.A.

6Teldat C+ Router Family

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Teldat Netzwerk-Router Handbücher

Teldat

Teldat Connect-104 Bedienungsanleitung

Teldat

Teldat bintec elmeg Regesta PRO PLC Bedienungsanleitung

Teldat

Teldat Teldat V Bedienungsanleitung

Teldat

Teldat Connect-FW Bedienungsanleitung

Teldat

Teldat iM8 Bedienungsanleitung

Teldat

Teldat 4Ge Bedienungsanleitung

Teldat

Teldat C1+L Bedienungsanleitung

Teldat

Teldat Connect-FW5G Bedienungsanleitung

Teldat

Teldat RXL15000 Bedienungsanleitung

Teldat

Teldat RS1800 Series Bedienungsanleitung

Teldat

Teldat ATLAS 160 Bedienungsanleitung

Teldat

Teldat REGESTA-PRO-ER Series Bedienungsanleitung

Teldat

Teldat Edge Router Atlas-840 Bedienungsanleitung

Teldat

Teldat H1 RAIL Series Bedienungsanleitung

Teldat

Teldat H1 HSDPA Bedienungsanleitung

Teldat

Teldat M8-Smart Bedienungsanleitung

Teldat

Teldat Atlas-i70 Bedienungsanleitung

Teldat

Teldat iM8 Bedienungsanleitung

Teldat

Teldat Regesta-PRO ER B Bedienungsanleitung

Teldat

Teldat C Bedienungsanleitung

Teldat

Teldat Regesta Smart PLC Bedienungsanleitung

Teldat

Teldat 4Ge Bedienungsanleitung

Teldat

Teldat Connect 104KF TLDPM00A1 Bedienungsanleitung

Teldat

Teldat T200 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise