Teldat ATLAS 300 Bedienungsanleitung

ATLAS 300 Installation Manual

Teldat-Dm 699-I

Teldat S.A. Manual

ATLAS 300 Installation Manual 1

Legal Notice

Warranty

This publication is subject to change.

Teldat S.A. offers no warranty whatsoever for information contained in this manual.

Teldat S.A. is not liable for any direct, indirect, collateral, consequential or any other damage connected to the deliv-

ery, supply or use of this manual.

Manual Teldat S.A.

2ATLAS 300 Installation Manual

Table of Contents

I ImportantInformation................................ 1

Chapter1 Introduction..................................... 2

1.1 Recycling and the Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Chapter2 InstallingtheRouter ................................ 4

2.1 GeneralInstallation................................... 4

2.2 Connections...................................... 4

2.2.1 LANEthernetconnection ................................ 5

2.2.2 WAN or external modem connection . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.2.3 Connecting: Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.3 Rackinstallation.................................... 6

2.4 Switchingtherouteron................................. 6

Chapter 3 Description of the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3.1 DescriptionoftheLEDs................................. 8

3.2 Description of the microswitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.2.1 Procedure to ignore the configuration . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Chapter4 Appendices.................................... 12

4.1 SmartCard ..................................... 12

4.1.1 Description and insertion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.1.2 Viewingthecontent.................................. 12

4.1.3 Writing ....................................... 13

4.1.4 AccessMode .................................... 14

4.1.5 Formatting...................................... 15

4.2 Troubleshooting................................... 15

4.3 Updating the software and configurations . . . . . . . . . . . . . . . . . . . . . . . . 16

4.3.1 UpdatingviaFTP................................... 16

4.3.2 UpdatingviaXModem................................. 17

4.4 Connectorspecifications................................ 19

4.4.1 Twisted pair connections (RJ45) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4.4.2 WANConnector................................... 19

4.4.3 AUXportconnections................................. 20

4.5 Technicalspecifications................................ 20

4.6 InstallingPMCCards................................. 21

Teldat S.A. Table of Contents

ATLAS 300 Installation Manual i

4.7 Translated safety warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Table of Contents Teldat S.A.

ii ATLAS 300 Installation Manual

I Important Information

Note

The manufacturer reserves the right to make changes and improvements to the software and hardware

of this product, modifying the specifications of this manual without prior notice.

Teldat S.A. Important Information

ATLAS 300 Installation Manual 1

Chapter 1 Introduction

The ATLAS 300 router, developed by TELDAT, is designed to operate in a wide range of scenarios present in the

most common teleprocessing networks: corporate, SME and SOHO.

Through its LAN/WAN connections, this device offers IP router functionality, supporting OSPF and other dynamic

routing protocols. The ATLAS 300 also offers a variety of connection possibilities in SNA environments: from LLC2

and SDLC to QLLC conversion, which allows direct LAN interconnection to the ATLAS 300 (without a communica-

tions card in the server), to the SNA over IP function using Data Link Switching (DLSw). This option has enabled all

transport network architecture to be standardized on TCP/IP.

In its basic configuration, the ATLAS 300 is equipped with two LAN interfaces and three serial WAN interfaces. Teld-

at and PCI Mezzanine Cards (PMC), capable of supporting encryption, voice over IP (VoIP), xDSL, etc., can be in-

serted to expand the configuration.

Fig. 2: User scenario: Teleprocess tasks

Fig. 3: User scenario: VoIP

1.1 Recycling and the Environment

The ATLAS 300 should never be disposed of with normal household waste. Please check with your town or city hall

about proper disposal that does not ruin the environment. Always comply with the current regulations on waste dis-

posal. Conviction of environmental law violation can result in fines and other legal penalties.

The cardboard box, the plastic packaging and the components that make up the ATLAS 300 may be recycled in ac-

cordance with the current recycling regulations in force in your country.

The symbol shown below, with a cross over the rubbish container, can be seen on the device. This means that, when

a device reaches the end of its life, it must be taken to a waste collection point and disposed of separately from other

1 Introduction Teldat S.A.

2ATLAS 300 Installation Manual

urban waste.

Teldat S.A. 1 Introduction

ATLAS 300 Installation Manual 3

Chapter 2 Installing the Router

The ATLAS 300 multimedia router can be a desktop or a rack-mounted device. In both cases, please be sure to fol-

low the recommendations given below to ensure correct installation:

Important

BEFORE CONNECTING THE ROUTER, PLEASE READ THE FOLLOWING INSTRUCTIONS CARE-

FULLY.

2.1 General Installation

Workplace Conditions

The following recommendations should be noted:

(1) Do not expose the device to direct sunlight, extreme heat, dampness or dusty conditions. Do not place the

device among books, papers or other elements that could hinder natural air circulation.

(2) Do not place the device near strong electromagnetic fields, such as those produced by speakers, motors, etc.

(3) Avoid knocks and/or strong vibrations during transport, operation and storage.

Power supply

The ATLAS 300 does not require any special conditions in terms of voltage stability or protection against power mal-

functions, as it is already protected.

To avoid electric shocks, residual current circulation and other unwanted effects that may disrupt communication, the

following is recommended:

Warning

All interconnected communication devices should be plugged to THE SAME GROUNDED

POWER OUTLET, which should, at the same time, be of good quality (lower than 10 ohms).

Whether the workplace is provided with an uninterrupted power supply system (UPS), regulated

supply, or it is independent from the rest (such as lighting, etc.), it is highly recommended that

all data devices should be connected to the same power source. This will avoid operating and

premature aging problems of drivers and other components.

Warning

The electric current in power cables, telephone lines and communication cables is dangerous.

To prevent electric shocks, before installing, handling or opening the equipment covers, con-

nect and disconnect the cables following the steps set forth in the following section.

To connect the ATLAS300 To disconnect the ATLAS300

Make sure the power switch is OFF. Switch off the device.

Connect all the data cables. Disconnect the power supply cable.

Connect the power supply cable. Disconnect the data cables.

Switch on the device.

2.2 Connections

2 Installing the Router Teldat S.A.

4ATLAS 300 Installation Manual

2.2.1 LAN Ethernet connection

The LAN interface has two female RJ45 connectors to connect to the Ethernet 10BaseT / 100BaseT networks. Con-

nect them through shielded (STP), or unshielded (UTP) twisted pair cables. Since these cables are not supplied with

the router and must be purchased separately, please contact your supplier.

Depending on the design of the network, the connection is done through a HUB or straight to the Ethernet interface

of another terminal device by means of a crossover cable (please contact your supplier for information on Ethernet

crossover cables).

2.2.2 WAN or external modem connection

DTE/DCE multi-standard serial interfaces have a female DB25 connector to connect to an external modem or to net-

works such as X.25, Frame Relay, etc.

The type of cable required will depend on the type of connection. This cable can be supplied by Teldat.

A flap on the underside of the device provides access to the sockets where the V.24 DTE/DCE, V.35 DTE/DCE, X.21

DTE/DCE and RS-485 2/4 wire drivers can be inserted. The drivers are not multipurpose and have a Tand an M

stenciled at either end. Define the mode you want by simply inserting the Tend of the driver into the connector (if you

want terminal mode) or the Mend (if you want modem). Bear in mind that RS-485 drivers cannot change the behavi-

or from modem to terminal. Setting 2-wire or 4-wire operation is done via the router’s application software, using the

associated interface’s configuration commands. This driver must always be connected to the 2H/4H marking, with

the arrow pointing towards the rear of the device (closest to the external connector).

Note

The default configuration for the drivers is shown on a label at the bottom panel of the device, close to

the flap used to access the drivers.

The configuration of the drivers included in Figure 3 shows WAN 3 operating in DCE mode and WAN 2 in DTE

mode. No driver is inserted in WAN 1 and the connectors are shown for didactic purposes.

Fig. 5: Driver insertion, depending on the operating mode

2.2.3 Connecting: Configuration

The ATLAS 300 routers have a DB-9 female connector on the rear panel labeled AUX. This provides access

to the router’s local console for configuration and monitoring. To use it, connect the AUX port to an asyn-

chronous terminal (or to a PC with terminal emulation).

Fig. 6: Connection for configuration/monitoring via console

Terminal configuration is as follows:

Teldat S.A. 2 Installing the Router

ATLAS 300 Installation Manual 5

- Speed: 9600 bps

- Eight data bits

- No parity bit

- One stop bit

- No type of flow control

Also expressed as 9600 8N1. The DB-9 female to DB-9 male cable supplied with the device can be used to connect

to the configuration port. If the asynchronous terminal is equipped with DB25 connectors, you should use an addi-

tional DB9F to DB25F adapter (not included with the device).

This can also be used to update codes. For further information, please see Updating the software and configura-

tions on page 16.

2.3 Rack installation

To install the ATLAS 300 in a 19-inch rack you will need two plastic mounting brackets, as shown in Figure 5. Mount-

ing brackets and screws are not included with the device and must be purchased separately.

Each mounting bracket is attached to the device using four screws (two at each side), as shown below:

Fig. 7: Attaching the brackets

The ATLAS 300 router comes with caps covering the screw holes. Remove these using a sharp tool (such as a

small flat screwdriver). We recommend removing the upper cover to do this.

Fig. 8: Router with the strips attached

2.4 Switching the router on

Once the device has been installed in the workplace according to the foregoing instructions, it is time to switch it on.

When the device is switched on, the auto-test and initialization begins (as explained below).

First, the device carries out a brief auto-test to check that the startup program is correct and to detect and activate

the SDRAM present in the device. At each stage of the process, a LED lights up in yellow (starting with the SLED). If

2 Installing the Router Teldat S.A.

6ATLAS 300 Installation Manual

Inhaltsverzeichnis

Andere Teldat Netzwerk-Router Handbücher

Teldat

Teldat Atlas 250 Bedienungsanleitung

Teldat

Teldat Connect-FW5G Bedienungsanleitung

Teldat

Teldat IMBER SMART Bedienungsanleitung

Teldat

Teldat Connect-4GePlus Bedienungsanleitung

Teldat

Teldat Connect-FW Bedienungsanleitung

Teldat

Teldat Teldat-3Ge Bedienungsanleitung

Teldat

Teldat 4Ge Bedienungsanleitung

Teldat

Teldat M2 Bedienungsanleitung

Teldat

Teldat Router Bedienungsanleitung

Teldat

Teldat REGESTA-PRO-ER Series Bedienungsanleitung

Teldat

Teldat ATLAS 60 NW Bedienungsanleitung

Teldat

Teldat H1 HSDPA Bedienungsanleitung

Teldat

Teldat WWAN Enabler Bedienungsanleitung

Teldat

Teldat T200 Bedienungsanleitung

Teldat

Teldat RS300 Series Bedienungsanleitung

Teldat

Teldat Teldat-3Ge-USB Bedienungsanleitung

Teldat

Teldat M2 Bedienungsanleitung

Teldat

Teldat Regesta Smart PLC Bedienungsanleitung

Teldat

Teldat Regesta Lite AU Bedienungsanleitung

Teldat

Teldat H2 RAIL Bedienungsanleitung

Teldat

Teldat RXL14000 Bedienungsanleitung

Teldat

Teldat iM8 Bedienungsanleitung

Teldat

Teldat Regesta-PRO ER B Bedienungsanleitung

Teldat

Teldat Connect-104 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise