Teldat T200 Bedienungsanleitung
Teldat T200 Router Family
Teldat-Dm 418-I
Copyright© Version 3.2 Teldat S.A.
Teldat S.A. Manual
Teldat T200 Router Family 1
Legal Notice
Warranty
This publication is subject to change.
Teldat S.A. offers no warranty whatsoever for information contained in this manual.
Teldat S.A. is not liable for any direct, indirect, collateral, consequential or any other damage connected to the deliv-
ery, supply or use of this manual.
Manual Teldat S.A.
2Teldat T200 Router Family
Table of Contents
I ImportantInformation................................ 1
Chapter1 Installation...................................... 2
1.1 Introduction...................................... 2
1.1.1 Recycling and the Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.2 Connections...................................... 3
1.2.1 PowerSourceConnection................................ 3
1.2.2 DataConnections.................................... 4
1.3 MeaningoftheLEDs.................................. 6
1.4 Programming the microswitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.4.1 Procedure to ignore the configuration, or establish the default configuration . . . . . . . . . . 7
Chapter2 Appendix...................................... 9
2.1 TroubleShooting.................................... 9
2.2 SoftwareUpgrading................................... 9
2.3 Connectors ...................................... 9
2.3.1 LAN Connector (FE 0 and Switch) . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.3.2 SERIALConnector.................................. 10
2.3.3 ConfigurationConnector................................ 11
2.4 TechnicalSpecifications................................ 11
2.5 Translated safety warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Teldat S.A. Table of Contents
Teldat T200 Router Family i
Table of Contents Teldat S.A.
ii Teldat T200 Router Family
I Important Information
Note
The manufacturer reserves the right to make changes and improvements in the appropriate features in
either software or hardware of this product, modifying the specifications of this manual without prior no-
tice.
The images showing the front and back panels of the device are for information purposes only. Some
small modification may exist in the actual device.
The equipment is intended to be installed by Service Personnel and only handled by qualified person-
nel. If not, the device may be damaged and malfunction.
This device contains elements that are sensitive to electrostatic surges and shocks. Therefore, it is es-
sential when handling the equipment that an antistatic wriststrap is connected to the device chassis and
that this is placed on an antistatic mat. Furthermore, it is crucial to avoid any kind of contact between
the device components and necklaces, bracelets, rings, ties etc.
Teldat S.A. Important Information
Teldat T200 Router Family 1
Chapter 1 Installation
1.1 Introduction
The Teldat T200 is a general-purpose IP router, suitable for a wide range of applications (personal, SOHO/SME and
corporate environments). It adapts perfectly to plenty of IP scenarios, providing simultaneous access to Internet for
private LAN users and accommodating teleprocess networks and SNA support.
The Teldat T200 router has a 4 or 8 port Ethernet LAN Switch and a Fast Ethernet port that behaves as WAN. You
can configure a serial port in the 4-port model, which can be used in X.25, SDLC, Frame Relay scenarios or with an
external backup device.
This manual shows you how to install and connect the router.
Fig. 1: Teldat T200G: External aspect
Fig. 2: Teldat T200: External aspect
1.1.1 Recycling and the Environment
Please do not, under any circumstances, throw away any Teldat T200 routers with normal domestic waste. Ask your
local town hall for information on how to correctly dispose of them in order to protect the environment against e-
waste. Always respect the current laws regarding waste material. Anyone found violating the environmental laws will
be subject to fines and any additional steps established by law.
All the packing materials i.e. the cardboard box, plastic and any other packaging, together with the pieces making up
aTeldat T200 , must be recycled complying with the current active laws regarding recycling materials.
The symbol shown below with a cross over the rubbish container can be seen on the device. This means that, when
a device reaches the end of its life, it must be taken to the official recycling/disposal centers where it must be dis-
posed of in an environmentally responsible manner and separately from normal domestic waste.
1 Installation Teldat S.A.
2Teldat T200 Router Family
1.2 Connections
Note
BEFORE INSTALLING THE ROUTER, PLEASE READ THE FOLLOWING INSTRUCTIONS CARE-
FULLY
Workplace Conditions. Main Characteristics
• Excessive cold and heat should be avoided, as should humidity and dust.
• Avoid direct exposure to sunlight and any other heat sources. Do not place the device between papers, magazines
or other items that could hinder natural air circulation.
• Do not place the device near strong electromagnetic fields such as those produced by speakers, motors, etc.
• Avoid knocks and/or strong vibrations during operation, storage and transport.
Warning
The electric current in power cables, telephone lines and communication cables is dangerous. To pre-
vent electric shocks, before installing, handling or opening the equipment covers, connect and discon-
nect the cables following the steps set forth in the following section.
To Connect To Disconnect
Make sure the device’s power supply is OFF. Switch off the device.
Connect all data cables. Disconnect the power supply.
Connect the power supply to the device. Disconnect the data cables.
Turn the switch ON.
1.2.1 Power Source Connection
The Teldat T200 does not require any special conditions regarding voltage stability or protection against power loss,
as it is already protected.
To avoid electric shocks, residual current circulation and any other unwanted effects that may disrupt communica-
tion, the following is recommended:
Warning
All interconnected communication devices should be plugged to THE SAME GROUNDED POWER
OUTLET, which should, at the same time, be of good quality (lower than 10 ohms).
Whether the workplace is provided with an uninterrupted power supply system (UPS), regulated supply,
or it is independent from the rest (such as lighting, etc.), it is highly recommended that all data devices
should be connected to the same power source. This will avoid operating and premature aging prob-
lems of drivers and other components.
To connect the power source to the device: ensure the switch is OFF (0) and the power supply is NOT connected to
the main electricity supply; find the POWER plug (located on the rear panel of the device) and plug it into the power
source. Both the connector and the receptacle are designed to ensure their proper installation.
Teldat S.A. 1 Installation
Teldat T200 Router Family 3
Fig. 3: T200G Power connection and switch
Fig. 4: T200 Power connection and switch
1.2.2 Data Connections
The Teldat T200 is equipped with the following connectors (although some of these may not be available depending
on the model):
SWITCH:
The Teldat T200 incorporates a 4 or 8 port Switch 10/100BaseT with automatic MDI/MDIX for LAN (local area net-
work) connection. It also has a LED indicating connectivity.
Please pay close attention to the labelling to avoid confusing the switch with other port types.
Fig. 5: T200G 8 port Switch (LAN)
Fig. 6: T200 4 port Switch (LAN)
FE 0:
The Teldat T200 has one female RJ45 connector in order to connect to the Ethernet 10BaseT / 100BaseT networks
through shielded twisted pairs (STP) or unshielded (UTP) cables.
Depending on the design of the network, the connection is carried out through a HUB or directly to another terminal
device Ethernet interface through a crossover cable (please consult your supplier for information on crossover Ether-
net cables).
Fig. 7: T200G Fast Ethernet Port (FE 0)
1 Installation Teldat S.A.
4Teldat T200 Router Family
Fig. 8: T200 Fast Ethernet Port (FE 0)
SERIAL:
Multistandard serial interface to connect an external modem, POS, or to connect to a WAN (wide area network) such
as X.25, Frame Relay, PPP, etc.
It requires an insertable driver (V.24, V.35, V.36, X.21, RS-485) to operate.
Fig. 9: SERIAL connector
1.2.2.1 Connecting for configuration
The Teldat T200 has a RJ45 female connector on the rear panel labeled CONF. ,which provides access to the
router’s local console. For configuration purposes, connect the CONF. port to an asynchronous terminal (or
to a PC with terminal emulation).
Fig. 10: T200G Configuration connector (CONF.)
Fig. 11: T200 Configuration connector (CONF.)
The terminal configuration is as follows:
- Speed: 9600 bps
- Eight data bits
- One stop bit
- No parity bit
- No type of flow control
To connect to the configuration port, use the RJ45 connector cable and the RJ45 female-DB9 female adaptor, both
provided with the router. In cases where the terminal has DB25 connections, you must use an additional adapter.
Teldat S.A. 1 Installation
Teldat T200 Router Family 5
Fig. 12: Connecting for configuration
1.3 Meaning of the LEDs
Fig. 13: Teldat T200 : Front panel
Fig. 14: Teldat T200 : Front panel
ON Power-on indicator. It lights up when connected to the power.
SRouter operation:
OFF: System off.
GREEN: System initialized and operating.
YELLOW: System with Telnet session established.
FE 0 Fast Ethernet - WAN:
OFF: Interface not supported or not available.
RED: Interface is not available either because it is not enabled or there is a mal-
function in the auto-test.
YELLOW: Interface initialization in process.
GREEN: Interface available. Blinking: Maintenance frame being sent.
SW
(T200G)
Switch(es) LAN Ethernet:
OFF: Switch(es) not available.
RED: Active Switch(es), there are no active devices connected.
GREEN: Active Switch(es), there is at least one active device connected.
Blinking: “heartbeat”.
LAN Switch(es) LAN Ethernet:
1 Installation Teldat S.A.
6Teldat T200 Router Family
Inhaltsverzeichnis
Andere Teldat Netzwerk-Router Handbücher
Teldat
Teldat H1 HSDPA Bedienungsanleitung
Teldat
Teldat SDE Bedienungsanleitung
Teldat
Teldat IMBER SMART Bedienungsanleitung
Teldat
Teldat Connect-FW Bedienungsanleitung
Teldat
Teldat Regesta Smart PRO Bedienungsanleitung
Teldat
Teldat RS123 Seies Bedienungsanleitung
Teldat
Teldat ATLAS 150 Bedienungsanleitung
Teldat
Teldat 4Ge Bedienungsanleitung
Teldat
Teldat H2 RAIL Bedienungsanleitung
Teldat
Teldat Edge Router Atlas-840 Bedienungsanleitung
Teldat
Teldat H2 RAIL Bedienungsanleitung
Teldat
Teldat K Seres Bedienungsanleitung
Teldat
Teldat C1+L Bedienungsanleitung
Teldat
Teldat ATLAS 60 NW Bedienungsanleitung
Teldat
Teldat iM8 Bedienungsanleitung
Teldat
Teldat Teldat-3Ge-USB Bedienungsanleitung
Teldat
Teldat bintec elmeg Regesta PRO PLC Bedienungsanleitung
Teldat
Teldat Connect 104KF TLDPM00A1 Bedienungsanleitung
Teldat
Teldat Atlas-i70 Bedienungsanleitung
Teldat
Teldat C Bedienungsanleitung
Beliebte Netzwerk-Router Handbücher anderer Marken
NETGEAR
NETGEAR FS526T - Switch Bedienungsanleitung
Korenix
Korenix JetNet 5710G Series Bedienungsanleitung
Automated Logic
Automated Logic ZN551 Betriebsanleitung
Cisco
Cisco ASR 1000 Series Bedienerhandbuch
EnGenius
EnGenius ESR-9710 Bedienungsanleitung
Cisco
Cisco 805 Series Bedienungs- und Sicherheitshinweise