Teldat ATLAS 150 Bedienungsanleitung

ATLAS 150

Installation Manual

Doc. Dm697-I Ver. 1.0

November, 2006

Index

I - Chapter. Installing the Router............................................................... I-1

I - 1. Introduction..............................................................................I-1

I - 1.1. Recycling and the Environment...................................I-2

I - 2. Connections..............................................................................I-3

I - 2.1. Power Source Connection............................................I-3

I - 2.2. Data Connection ..........................................................I-4

I - 2.2.1. BRI Connection.....................................................I-6

I - 2.2.2. WAN or external MODEM connection.................I-7

I - 2.2.3. Connecting the antenna..........................................I-7

I - 2.2.4. Connecting for configuration.................................I-7

I - 3. Meaning of the LEDs...............................................................I-9

I - 4. Programming the Microswitches............................................I-10

I - 4.1.1. Procedure to ignore the configuration..................I-10

I - 5. PMC-PCI Cards .....................................................................I-12

I - 5.1. Procedure to install PMC Cards.................................I-12

II - Chapter. Appendices.............................................................................II-14

II - 1. Troubleshooting ................................................................... II-14

II - 2. Updating the Software.......................................................... II-15

II - 3. Connectors ........................................................................... II-16

II - 3.1. LAN Connector (FE x) ............................................ II-16

II - 3.2. BRI Connector......................................................... II-16

II - 3.3. SERIAL Connector.................................................. II-16

II - 3.4. ANT Connectors...................................................... II-17

II - 3.5. Configuration Connectors........................................ II-18

II - 4. Technical Specifications....................................................... II-19

The manufacturer reserves the right to make changes and improvements in

the appropriate features in either software or hardware of this product,

modifying the specifications of this manual without prior notice.

The images presented on the front and back panels of the devices are

provided as an information guideline only. Some small modifications may

exist in the actual device.

The equipment must be handled by qualified personnel; contrariwise, the

device may be damaged and consequently malfunction.

This device contains elements that are sensitive to electrostatic surges and

shocks, therefore it is essential when handling the equipment that an

antistatic wriststrap is connected to the device chassis and this is placed on

an antistatic mat; and furthermore avoiding any kind of contact between the

device components and necklaces, bracelets, rings, ties etc.

I - Chapter.

Installing the Router

I - 1. Introduction

The ATLAS 150 is a modular device incorporating encryption hardware and

designed with network convergence in mind as it supports IP Telephony and the

possibility to encode video.

Teldat proposes the ATLAS 150 for wireless technology, both for the local

network, with wireless access point functionality, as well as for the wide area

network as this device supports the following interface cards: GSM, GPRS,

EDGE, UMTS, HSDPA, CDMA2000, EV-DO and WiMAX.

The ATLAS 150 executes the Teldat CIT (Teldat Internetworking Code -

Código de Internetworking de Teldat), which runs over all the Teldat router

families and is characterized by a wide variety of functionalities they support and

especially orientated to satisfy the access requirements to corporate data networks.

Some of the outstanding features available with CIT are the management capacity,

the possibility to implement Quality of Service mechanisms, security mechanisms

and the possibility to create Virtual Private Networks as well as an extensive

range of protocols and IP routing functionalities.

This manual shows you how you need to install and connect this device.

ATLAS 150 front panel

ATLAS 150

Installation

I-1

Doc. Dm697-I

Rev. 1.0

ATLAS 150 rear panel

I - 1.1. Recycling and the Environment

Please do not under any circumstances throw away any ATLAS 150 with

normal domestic waste. Ask your local town hall for information on how to

correctly dispose of them so protecting the environment against e-waste. Always

respect the current laws regarding waste material. Anyone found violating the

environmental laws will be subject to fines and any additional steps established by

law.

All the packing materials i.e. the cardboard box, plastic and any other packaging

together with the pieces making up an ATLAS 150 must be recycled

complying with the current active laws regarding recycling materials.

The below symbol with a cross over the rubbish container can be seen on the

device. This means that when a device reaches the end of its life, it must be taken

to the official recycling/disposal centers where it must be disposed of in an

environmentally responsible manner and separately from normal domestic waste.

ATLAS 150

Installation

I-2

Doc. Dm697-I

Rev. 1.0

ATLAS 150

Installation

I-3

Doc. Dm697-I

Rev. 1.0

I - 2. Connections

BEFORE CONNECTING THE ROUTER PLEASE READ THE

FOLLOWING INSTRUCTIONS CAREFULLY

Workplace Conditions. Main Characteristics

•Areas with excessive humidity and dust should be avoided.

•Direct exposure to sunlight should be avoided as well as other heat sources.

The device should not be placed amongst books, papers, magazines or other

element that could hinder natural air circulation.

•The device should not be placed very close to strong electromagnetic fields

such as speakers, engines, etc.

•Knocks and/or strong vibrations should be avoided during transport, operation

and storage.

WARNING: Electric supply current, telephone and communication cables are

dangerous. To prevent electric shock while installing, moving or opening the

device covers, cables should be disconnected and connected as follows:

To Connect To Disconnect

Ensure that the on/offpower supply switch is in

the OFF position Place the on/off power supply switch in the

OFF position

Check that the power supply is not connected to

either the main electricity supply or the device Disconnect the power supply from the main

electricity supply

Connect all data cables Disconnect the power supply from the device

Connect the power supply to the device Disconnect the data cables

Connect the power supply to the main electricity

supply

Place the device’s on/off power supply switch in

the ON position

I - 2.1. Power Source Connection

The ATLAS 150 router is powered with an external AC/DC source.

To avoid electric shocks, residual current circulation and other unwanted effects,

also affecting communications, the following is recommended:

•It is highly recommended that all interconnected communication

devices are plugged to THE SAME GROUNDED POWER

OUTLET, which should at the same time be of good quality (lower

than 10ohms).

•Whether the workplace is provided with an uninterrupted power

supply system (UPS), regulated supply or it is independent from the

rest (such as lighting, etc.); it is highly recommended that all data

devices should be connected to the same power source. This will

avoid operating and premature aging problems of drivers and other

components.

Power supply connection with external source

To connect the power source to the device, follow the steps listed in the earlier

table: ensure that the switch is OFF (0) and the power supply is NOT connected

to the main electricity supply; find the POWER plug, located on the rear panel of

the device and plug it into the power source: both the connector and the receptacle

are designed so it is only possible to insert it in the correct position.

For subsequent connection of the power source to the main electricity supply, use

the grounded cable provided for this purpose.

ATLAS 150

Installation

I-4

Doc. Dm697-I

Rev. 1.0

I - 2.2. Data Connection

The ATLAS 150 router has the following connectors available. Some of these

connectors may not be available depending on the model:

FE 0, FE 1:

The ATLAS 150 has two female RJ45 connectors in order to connect to the

Ethernet 10BaseT / 100BaseT networks through shielded twisted pairs (STP) or

unshielded (UTP) cables.

Depending on the design of the network, the connection is carried out through a

HUB or directly to another terminal device Ethernet interface through a crossover

cable (please consult your supplier for information on crossover Ethernet cables).

The second LAN (FE 1) requires a software license in order to operate.

BRI:

ISDN 2B-D basic interface; this has an activation mechanism, through 2 jumpers,

for the S bus terminal load.

This requires a software license in order to operate.

SERIAL:

Serial interface in order to connect to a WAN or an external modem.

ANT.:

RF antenna connectors.

So that the Wireless LAN interface is operative, the device must have a plug-in

Wireless LAN card and the corresponding software license. Depending on the

model, the antennas are installed in the device at the factory. If your device does

not have the Wireless LAN module incorporated, you can obtain this later on.

The manual accompanying this module will indicate how to install it and the

corresponding antenna cables in the device.

ATLAS 150

Installation

I-5

Doc. Dm697-I

Rev. 1.0

I - 2.2.1.

BRI Connection

The BRI interface has a 4 wire RJ45 female connector in order to connect to the S

bus coming from the ISDN network terminator (NT1 or TR1).

In order to connect, use the cable with RJ45 male connections provided with the

device.

Passive-Bus terminal resistances

The ATLAS 150 router has a pushbutton (labeled as “TERM”) in order to

connect the BUS-S termination resistances. The placing of these terminal

resistances in the correct position is important as contrariwise this can lead to

errors in data (or voice), particularly if the “S” bus line is long. On leaving the

factory, the pushbutton, by default, is in the “ON” position.

•The only or last terminal on the ISDN “S” bus

The “TERM” pushbutton must be in the ON position if the router is the only

element connected to the network terminal (NT1, TR1, etc) or is in the last

position on the ISDN “S” bus.

hecho por M .A. Ber ro jo

Atlas

Teldat

NT1 / TR1

S interface

(4 wires)

ISDN

U interface

(2 wires)

Location as the only or last terminal

•Intermediate position in the ISDN “S” bus

The “TERM” pushbutton must be in the OFF position if the router occupies

an intermediate position in the ISDN “S” bus.

ATLAS 150

Installation

I-6

Doc. Dm697-I

Rev. 1.0

hechoporM.A. Berrojo

Atlas

Teldat

NT1 / TR1

S interface

(4 wires)

ISDN

U interface

(2 wires)

Location in an intermediate position in the bus

I - 2.2.2.

WAN or external MODEM connection

The DTE/DCE multistandard serial interfaces have a DB25 female connector in

order to connect to an external modem or for connection to X.25, Frame Relay

networks, etc.

Depending on the type of connection established, a different type of cable will be

needed. This cable can be supplied by Teldat if you wish.

On the inside of the device, there is a slot to insert the driver which could be V.24

DTE/DCE, V.35 DTE/DCE and X.21 DTE/DCE. These drivers are not multi-

purpose. The configuration for the operation mode is carried out by inverting the

position of the driver (this appears labeled as “T” indicating that this acts as

terminal, and “M” indicating modem functions). The operation mode is that

indicated by the label closest to the connector.

The default configuration for the drivers (on leaving the factory) is

indicated on a label located on the underside of the device.

I - 2.2.3.

Connecting the antenna

The ATLAS 150 router has two connectors to connect an external antenna

which improves the quality of the signal received and transmitted through the

Wireless LAN module. This module is optional; it is possible that your device

does not have Wireless LAN and consequently no antennas. To assemble and

disassemble the antennas, simply screw them into the connectors labeled as ANT

located on the rear of the device.

ATLAS 150

Installation

I-7

Doc. Dm697-I

Rev. 1.0

I - 2.2.4.

Connecting for configuration

The ATLAS 150 router has a RJ45 female connector on the rear panel referred

to as “CONF.”which provides access to the device’s local console. In order to

Inhaltsverzeichnis

Andere Teldat Netzwerk-Router Handbücher

Teldat

Teldat ATLAS X60 Bedienungsanleitung

Teldat

Teldat Atlas 250 Bedienungsanleitung

Teldat

Teldat REGESTA-PRO-ER Series Bedienungsanleitung

Teldat

Teldat iM8-Cx Bedienungsanleitung

Teldat

Teldat Regesta Smart PLC Bedienungsanleitung

Teldat

Teldat H1 RAIL Series Bedienungsanleitung

Teldat

Teldat Regesta-PRO ER B Bedienungsanleitung

Teldat

Teldat IMBER SMART Bedienungsanleitung

Teldat

Teldat C+ Series Bedienungsanleitung

Teldat

Teldat ATLAS 300 Bedienungsanleitung

Teldat

Teldat 4Ge Bedienungsanleitung

Teldat

Teldat Teldat-3Ge Bedienungsanleitung

Teldat

Teldat WWAN Enabler Bedienungsanleitung

Teldat

Teldat Regesta Smart PRO Bedienungsanleitung

Teldat

Teldat M1 Bedienungsanleitung

Teldat

Teldat Atlas 250 Bedienungsanleitung

Teldat

Teldat TLDPV00A1 Bedienungsanleitung

Teldat

Teldat RXL14000 Bedienungsanleitung

Teldat

Teldat 3ge Bedienungsanleitung

Teldat

Teldat M1 Bedienungsanleitung

Teldat

Teldat H2 RAIL Bedienungsanleitung

Teldat

Teldat T200 Bedienungsanleitung

Teldat

Teldat M8-Smart Bedienungsanleitung

Teldat

Teldat iM8 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise