Teledyne Lecroy MS-500 Bedienungsanleitung

Operator's

Manual

MS-500 Mixed Signal

Oscilloscope Option

www. .com information@itm.com1.800.561.8187

MS-500 Mixed Signal Oscilloscope Option Operator's Manual

Unauthorized duplication of Teledyne LeCroy documentation materials

other than for internal sales and distribution purposes is strictly

prohibited. However, clients are encouraged to duplicate and distribute

Teledyne LeCroy documentation for their own internal educational

purposes.

MS-500 and Teledyne LeCroy are trademarks of Teledyne LeCroy, Inc.

Other product or brand names are trademarks or requested trademarks of

their respective holders. Information in this publication supersedes all

earlier versions. Specifications are subject to change without notice.

928336-00 Rev A3

April, 2017

www. .com information@itm.com1.800.561.8187

Operator's Manual

Contents

Introduction......................................................................................................... 1

Technical Overview....................................................................................................... 2

Standard Hardware....................................................................................................... 3

Accessories................................................................................................................... 5

Connecting the Mixed Signal Device ....................................................................7

Connecting to the Oscilloscope................................................................................... 7

Digital Connections.....................................................................................................10

Digital Setup...................................................................................................... 11

Digital Logic Setup......................................................................................................11

Digital Group Setup.....................................................................................................13

Displaying Digital Traces............................................................................................ 14

Renaming Digital Lines...............................................................................................15

Digital Triggering ............................................................................................... 16

Setting Up Digital Triggers .........................................................................................16

Pattern Trigger ............................................................................................................17

Edge Trigger ................................................................................................................20

Width Trigger...............................................................................................................21

Glitch Trigger...............................................................................................................22

Interval Trigger............................................................................................................23

Dropout Trigger ...........................................................................................................24

Qualified Trigger.......................................................................................................... 25

Reference.......................................................................................................... 26

Returning a Product for Service................................................................................. 26

Technical Support.......................................................................................................27

www. .com information@itm.com1.800.561.8187

MS-500 Mixed Signal Oscilloscope Option

Welcome

Thank you for purchasing a Teledyne LeCroy MS-500 Mixed Signal

Oscilloscope Option.

The MS-500 is a powerful solution for the challenge of measuring multiple,

mixed signals in a single oscilloscope. An enhancement to Teledyne

LeCroy oscilloscopes, the MS-500 extends their testing range by adding

18 or 36 digital channels for display or triggering.

This MS-500 manual assumes that you have a basic understanding of

discrete electronics, logic analyzers, and Teledyne LeCroy oscilloscopes,

specifically the model you will use with the MS-500. When necessary,

details on specific oscilloscope features are included in this manual.

Contact your nearest Teledyne LeCroy customer service center or national

distributor if anything is missing or damaged. We can only be responsible

for replacement if you contact us immediately.

Sincerely,

David C. Graef

Vice President and Chief Technology Officer

www. .com information@itm.com1.800.561.8187

Operator's Manual

Introduction

The MS-500 Mixed Signal Oscilloscope Option is a complete system that

adds digital acquisition and triggering capabilities to a Teledyne LeCroy

oscilloscope.

Once properly connected to the oscilloscope and the device under test,

you will be able to use the oscilloscope user interface for the following:

•Digital Logic Control: Set the logic threshold and hysteresis for each

lead bank, choosing from standard logic families or entering a custom

setting.

•Digital Group Management: Combine individual digital lines into bus

groups to be managed together. Give lines descriptive logical names,

regardless of the physical lead number.

•Digital Analysis: Display digital signals as single line traces or

collapsed bus traces. Many of the same tools available for analyzing

analog signals may be applied to digital signals.

•Digital and Combined Triggering: Choose to set an acquisition trigger

on a digital signal pattern or a combination of conditions using both

analog and digital signals.

The MS-500 is ideally suited for embedded controller testing where there

is a proliferation of analog signals coincident with digital signals. You can

easily debug signals using standard oscilloscope tools such as cursors,

measurement parameters, and zooming. Oscilloscopes compatible with

the MS-500 feature large, bright color displays to facilitate signal viewing,

plus all the connectivity and documentation capabilities needed to quickly

record and distribute information.

The MS-500 and MS-500-36 are identical except the MS-500-36 standard

configuration is for 36 channels. The MS-500-36 can be operated in 36 or

18 channel mode for higher performance. The MS-500 is configured as an

18 channel instrument and can be upgraded with an additional lead set to

support 36 channels. Both are referred to as MS-500 in this manual.

www. .com information@itm.com1.800.561.8187

MS-500 Mixed Signal Oscilloscope Option

Technical Overview

The MS-500 is an external device that digitally samples waveform data at

up to 2 GS/s (for 500 MHz digital signals). Unlike a logic analyzer, it

operates only in a Timing Analysis mode, so it requires 4x oversampling to

determine the correct digital edge position, and does not require the user

to input a clock.

While in SINGLE, NORMAL, or AUTO trigger mode, the MS-500 repeatedly

samples each digital channel’s voltage level. If the voltage is greater than

the threshold voltage, the MS-500 stores a 1 in internal memory.

Otherwise, a 0 is stored.

The minimum high voltage level may be defined by the user (using the

hysteresis controls) up to 1.4 V above the threshold. The maximum low

voltage level may be defined to 1.4 V below the threshold. The minimum

signal swing is 100 mV. The indeterminate range of 50 mV around the

threshold voltage level is the level below which the MS-500 will not

operate. However, the MS-500 can support a signal as low as 100 mV only

if the input signal’s quality is adequate.

The MS-500 keeps sampling its inputs until the oscilloscope is put into

STOP trigger mode. Data is stored in a 50 Mpt internal memory that is

periodically transferred to the oscilloscope via the USB2.0 cable. If the

oscilloscope is triggering in SINGLE or NORMAL trigger mode, data is

acquired and transferred only when the trigger condition is satisfied. The

captured data is displayed on the oscilloscope in a time-aligned fashion.

www. .com information@itm.com1.800.561.8187

Operator's Manual

In any trigger mode (AUTO, NORMAL, SINGLE), pressing STOP trigger

cancels the acquisition, which leaves the previously acquired data

unchanged.

The USB2.0 cable provides downloading of trigger conditions from the

oscilloscope to the MS-500 and uploading of digital data from the MS-500

to the oscilloscope.

Standard Hardware

The MS-500 is delivered with the following hardware:

Part Description

QTY

MS-500

(MS-500-36)

Mixed Signal

Accessory

Provides 18- or 36-channel digital acquisition and

triggering.

16" Digital

Leadset

Interfaces the MS-500 to the device under test.

The lead set terminates in a 25 mil pin socket.

Micro-gripper probes of various sizes are available

as accessories from Teledyne LeCroy, and may be

connected to the lead set. The lead set is divided

into two banks. Each lead within the bank is color-

coded (to resistor color-coding standard) and has

an individual ground connection. In addition, there

are two common ground leads available for use.

(2)

www. .com information@itm.com1.800.561.8187

MS-500 Mixed Signal Oscilloscope Option

Part Description

QTY

MS-500

(MS-500-36)

Bus Cable

1.3m cable to connect Mixed Signal Accessory to

the main oscilloscope unit, includes USB2.0 cable.

This connection provides timebase

synchronization, cross-triggering and power.

3" Flexible

Ground Lead

Lead for grounding individual digital inputs

(10)

Ground

Extender

Connect to ground port of any digital input and

make a simple signal and ground connection to a

0.1” square pin header.

(40)

Carrying

Case

Operator's

Manual

www. .com information@itm.com1.800.561.8187

Operator's Manual

Accessories

You may purchase these optional accessories separately:

Accessory

Part Number

Description

Digital Leadset

MSO-DLS-18

MSO-DLS-36

Additional 16" leadset for inputting lines

D0-D17 or D0-D35

. This can be useful if you

have more than one device under test and

don't wish to disconnect/reconnect leads.

MSO-DLS-36 available for MS-500-36 only.

Large Gripper

Probe Set

PK400-1

Large gripper probe set for 0.10 inch

(2.54 mm) pin pitch. Includes 10 probes with

color-coded leads.

Medium Gripper

Probe Set

PK400-2

Medium gripper probe set for 0.04 inch

(1.00 mm) pin pitch. Includes 10 probes with

color-coded leads.

www. .com information@itm.com1.800.561.8187

MS-500 Mixed Signal Oscilloscope Option

Accessory

Part Number

Description

Small Gripper

Probe Set

PK400-3

Small gripper probe set for 0.008 inch

(0.2 mm) pin pitch. Includes 10 probes with

color-coded leads.

Mictor Cable

MSO-MICTOR

Mictor Connection cable, 16" (40.64 cm),

36 channel connector

Interconnect

Cable

MSO-3M

Interconnect cable, 16" (40.64 cm), mates

with 3M connectors 2520-6002 and

2520-5002.

www. .com information@itm.com1.800.561.8187

Andere Handbücher für MS-500

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Teledyne Lecroy Prüfgeräte Handbücher

Teledyne Lecroy

Teledyne Lecroy WaveSurfer 3000 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy WaveRunner/MDA 8000HD Series Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy WaveSurfer 4000HD Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy T3AWG3K Series Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy HDO4032 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy WaveSurfer 4034HD Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy WaveSurfer 4000HD Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy WaveRunner/MDA 8000HD Series Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy frontline TLF 3000 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy RP2060 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy HDO4104A Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy WaveJet Touch Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy HDO9000 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy WaveSurfer 3104Z Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PXP500 PCI Express Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy 980 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy 780 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy AP033 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy WaveSurfer 3000z Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy WavePro HD series Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy ZS1000 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PP009-1 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy WaveSurfer 10 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy WaveMaster 8 Zi-B Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung