Teledyne GB300 Bedienungsanleitung

The Quick Start Guide describes the steps to successfully start, calibrate, and use the GB300 instrument.

Components

The GB300 Portable Oxygen Analyzer includes:

•Instrument and carrying case

•I-17 sensor

•Sensor interconnection cable

•T adapter P/N A268

•Barbed hose adapter P/N F1717

•3 AA batteries

•Quick Start Manual

Optional items:

•RS232 digital output

•Interface cable: 0-1 vdc P/N B75554

•Interface cable: RS232 P/N B75555

Set Up

Set up is simple:

1. Install the cable and sensor

2. Install 3 AA alkaline batteries.

3. Calibrate

Cable and Sensor Assembly

1. Insert the coiled cable connector into the right side of the instrument and secure the locking nut.

2. Remove the sensor from its protective package. Caution: If you see signs of moisture or liquid

in the protective bag do not open the package. Sensor contains caustic, which causes severe

burns and may be fatal if swallowed. The Material Safety Sheet can be found in the service

section of our web site at <www.teledyne-ai.com>

3. Connect the coiled cable to the sensor and secure the locking nut.

M-GB300-REV 2

Battery Installation

1. Hold the instrument face down.

2. Using a coin, gently twist to open the

hinged battery compartment door

latch.

3. Lift up door near latch and pull out.

4. Install 3 AA alkaline batteries

observing proper polarity.

Note: Use only alkaline batteries

Quick Start Guide for Model GB300 Portable Oxygen Analyzer

REV 2

Calibration

1. After installing the batteries and sensor the LCD will

read 00.0 and the battery indicator will show a full

charge with all bars activated. On initial start up with a

new sensor, allow the unit to stabilize for about 10

minutes before proceeding to the next step.

2. With the sensor exposed to room air or 100% oxygen,

press and hold the ON/OFF key down until the LCD

starts to count from 3 to 0. Release the key as soon as the

count starts and wait for the LCD to read 20.9 plus or

minus a few percent. Note: Holding ON/OFF key down

during the automatic calibration sequence will shut the

unit off when released. Excluding factors such as

temperature, humidity, and trace amounts of other gases,

the air we breathe contains 20.9% oxygen (calibration

point) and 79.1 % nitrogen. Subsequent calibrations

require that you first turn the unit on by pressing the ON/OFF key once. When the LCD

displays a value, press and hold the ON/OFF key until the LCD starts to count down as

noted above.

Gas Sampling

For flowing gas applications use the supplied adapter P/N C53790. When sampling, do not

pressurize the sensor as this will lead to incorrect readings. The sensor is a partial pressure device.

Any change in pressure from the calibration point will affect the reading.

Turning the Unit OFF

Press and release the ON/OFF key.

Specifications:

Range: 0-100% oxygen

Response time: 90% of final value in less than 10 seconds.

Sensor life: 36 months in air.

Battery life: Approximately 2000 hours.

Power: 3 AA alkaline batteries

Standard Output: 0-1 vdc.

Operating Temperature: 0-40 ˚C

Warranty: One (1) year against defects in material and workmanship.

M-GB300-REV 2

Inhaltsverzeichnis

Andere Teledyne Analytisches Instrument Handbücher

Teledyne

Teledyne 3060E Bedienungsanleitung

Teledyne

Teledyne 7120 Bedienungsanleitung

Teledyne

Teledyne PEM 9002 Bedienungsanleitung

Teledyne

Teledyne 9700 Bedienungsanleitung

Teledyne

Teledyne 9060L Bedienungsanleitung

Teledyne

Teledyne 3000MA Bedienungsanleitung

Teledyne

Teledyne 3010MA Bedienungsanleitung

Teledyne

Teledyne EV71YC1MCL2010-BA0 Bedienungsanleitung

Teledyne

Teledyne 311TC Bedienungsanleitung

Teledyne

Teledyne 3220 Bedienungsanleitung

Teledyne

Teledyne 3010TAC Bedienungsanleitung

Teledyne

Teledyne 3000PB Bedienungsanleitung

Teledyne

Teledyne 2120 Bedienungsanleitung

Teledyne

Teledyne 3010TB Bedienungsanleitung

Teledyne

Teledyne 6200A Bedienungsanleitung

Teledyne

Teledyne 3300TA Bedienungsanleitung

Teledyne

Teledyne 6000B Bedienungsanleitung

Teledyne

Teledyne 3500 Series Bedienungsanleitung

Teledyne

Teledyne 3000ZA Bedienungsanleitung

Teledyne

Teledyne T802 Bedienungsanleitung

Teledyne

Teledyne 3010PAC Bedienungsanleitung

Teledyne

Teledyne 2020 Bedienungsanleitung

Teledyne

Teledyne 3000PA Bedienungsanleitung

Teledyne

Teledyne 5000B Bedienungsanleitung

Beliebte Analytisches Instrument Handbücher anderer Marken

Cocraft

Cocraft NLT04 Bedienungsanleitung

M&C

M&C GENTWO PMA1000 Bedienungsanleitung

MICRO-EPSILON

MICRO-EPSILON optoncdt 1700 Bedienungsanleitung

CONDTROL

CONDTROL XP4 PRO Bedienungsanleitung

Extech Instruments

Extech Instruments BR200 Bedienungsanleitung

Dewetron

Dewetron DEWE-30-16 Produkthandbuch

EXTOL PREMIUM

EXTOL PREMIUM 8820043 Montage- und Bedienungsanleitung

RIDGID

RIDGID SeeSnake Compact Bedienungsanleitung

YDLIDAR

YDLIDAR TIA Bedienungsanleitung

Olympus

Olympus IPLEX FX Series Bedienungsanleitung

Bosch

Bosch GLM 50 C Professional Bedienungsanleitung

Reflecta

Reflecta DigiEndoscope Bedienungsanleitung

Chinavision

Chinavision CVACZ-G696 Montageanleitung

Fuji Electric

Fuji Electric ZKMA Bedienungsanleitung

VOLTCRAFT

VOLTCRAFT IC-100HD Bedienungsanleitung

RIDGID

RIDGID micro CA-25 Bedienungsanleitung

Würth

Würth MASTERVISION MINI REC Bedienungsanleitung

AMI

AMI 2001LC Bedienungsanleitung