Teledyne 402R-EU Bedienungsanleitung

TELEDYNE ANALYTICAL INSTRUMENTS

www.teledyne-ai.com

Model 402, 402R, 402REU: Start-up Procedure

Equipment needed: Digital multimeter (DMM)

Power cord

Document needed: Instruction manual

Gases needed:

Zero gas: Zero grade (representative of background gas)

Fuel: (40% H2 / 60% N2) or 100% H2

Air: Zero grade air

Span gas: (70-90% of range) ppm CH4 balance back ground)

Procedure:

1. Connect power cord to AC inlet

2. Position ON / OFF switch to ON

3. Connect zero grade air to analyzer, set the input pressure to 30 PSIG, adjust the air regulator inside the

sample module for 15 psig or as indicated in the instruction manual

4. Connect Zero gas to analyzer, set the pressure to 30 PSIG or same as sample pressure, adjust sample

bypass valve so the sample pressure gauge inside the sample module indicates the pressure in the

instruction manual, and sample bypass flow meter reads 0.5 to 2 SCFH

5. Connect fuel (40 / 60 mix or 100 H2 per application); set pressure to 30 PSIG

6. Check 0-1 VDC, 4-20 MA output, and alarm(s), by adjusting the zero and span pot to get the analyzer

reading from 0-100% of full scale

7. Let the analyzer run for 8 hours or overnight

8. After the sample cell temperature is stabilized, position range switch to Ignite; hold for 6 seconds, then

release to HI range

9. Wait until the analyzer reading is stabilized, introduce span gas, adjust fuel regulator in increments of

0.5 PSIG at a time, and watch for the analyzer reading to increase; continue to adjust fuel regulator until

the analyzer reading is increasing slower or the reading starts to decrease

10. Wait until the analyzer reading is stabilized, adjust span pot until the analyzer reads the concentration

in the cylinder

11. Introduce zero gas, wait until the reading is stabilized, adjust zero pot until analyzer reading is 0 ppm

12. Repeat steps 9 and 10 until no further adjustment is required

13. Connect sample to the analyzer, check the sample pressure and flow rate; now the analyzer is ready to

go on line

TELEDYNE ANALYTICAL INSTRUMENTS

www.teledyne-ai.com

NOTE: The flow restructures are:

Blanket air = 600 sccm

Sample = 30 sccm

Fuel = 200 sccm (Standard 40 / 60 mix)

Fuel = 30 sccm (100% H2)

When the background is hydrogen, the fuel port is connected to zero grade nitrogen

Andere Handbücher für 402R-EU

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Teledyne Messgerät Handbücher

Teledyne

Teledyne T100 Bedienungsanleitung

Teledyne

Teledyne 300 Bedienungsanleitung

Teledyne

Teledyne T3CP30-50 Bedienungsanleitung

Teledyne

Teledyne HASTINGS Everywhereyoulook 200 Series Bedienungsanleitung

Teledyne

Teledyne 6600 Bedienungsanleitung

Teledyne

Teledyne HASTINGS Everywhereyoulook 201 Series Bedienungsanleitung

Teledyne

Teledyne 9110AH Bedienungsanleitung

Teledyne

Teledyne Echotrac E20 Bedienungsanleitung

Teledyne

Teledyne 400E Bedienungsanleitung

Teledyne

Teledyne EXPLORER Bedienungsanleitung

Teledyne

Teledyne 2000A-EU Bedienungsanleitung

Teledyne

Teledyne 4220 Betriebsanleitung

Teledyne

Teledyne ADQ8-4X Bedienungsanleitung

Teledyne

Teledyne TIENet 360 LaserFlow Ex Betriebsanleitung

Teledyne

Teledyne 730 Bubbler Bedienungsanleitung

Teledyne

Teledyne PMAT 2000 Bedienungsanleitung

Teledyne

Teledyne 200A Bedienungsanleitung

Teledyne

Teledyne T360 Bedienungsanleitung

Teledyne

Teledyne TED 191 Bedienungsanleitung

Teledyne

Teledyne Frontline Sodera Bedienungsanleitung

Teledyne

Teledyne 200E Bedienungsanleitung

Teledyne

Teledyne Sierra M6-2 Bedienungsanleitung

Teledyne

Teledyne CEA 9001 Bedienungsanleitung

Teledyne

Teledyne N500 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung