Teledyne AX300 Bedienungsanleitung

The Quick Start Guide describes the steps to successfully start and

calibrate the instrument. This guide covers the AX/MX 300 series

of analyzers and monitors. Before placing the instrument in service

please read the users manual that accompanies the device.

Components

The AX/MX 300 Portable Oxygen Monitor includes:

•Sensor & Diverter

•Sensor Cable

•T-Adapter

•Vmount Adapter

•AA Batteries

•Instruction Manual

Set Up

Set up is simple:

1. Connect the coiled sensor cable to the

monitor and tighten the capture nut.

2. Connect the other end to the sensor

and tighten the capture nut.

3. Install 3 AA alkaline batteries.

Calibration

Note: The AX300 and MX300 can only be calibrated

using 100% oxygen or room air (20.9%). Improper

calibration or use of other gas concentrations will

activate the



SENSOR indicator.

Battery Installation

1. Hold the instrument face down.

2. Using a coin. Gently twist to open

the hinged battery compartment door

latch.

3. Lift up door near latch and pull out.

4. Install 3 AA alkaline batteries

observing proper polarity.

Note: Depressing keys while installing

battries may activate an error code.To

reset remove and replace battery.

Quick Start Guide for Model AX300 Portable Oxygen Anal

yzer and

MX300 Portable Oxygen Monitor

1. After installing batteries the LCD will flash 00.0.

2. Thread flow diverter onto the sensor, insert into the

plastic tee as shown above. Connect to a supply of pure

dry oxygen flowing at 1-2 liters per minute.

3. After 20 seconds press CAL key. The LCD will count

down from 9 to 0. When the calibration is complete the

LCD will display the gas value.

4. Press the LOCK/UNLOCK key to save the calibration

data. The LCD will stop flashing.

5. Check the batteries by pressing the BAT TEST key.

(MX300 only)

6. Remove the sensor from the oxygen supply and confirm

the LCD reads less than 22% in room air. It is not

necessary for it to read exactly 20.9.

Setting the Alarms (MX300 only)

HI Alarm

1. Unlock the control keys by pressing the

LOCK/UNLOCK key. The display will flash.

2. Press the HI ALARM SET key once. Press the

UP and DOWN arrow key until the desired

value is displayed in the lower right corner.

Press Lock key to save settings or proceed to

Low alarm setting below.

Note: The HI and LO alarms may be defeated

by setting the HI alarm limit one step

above 100%. The display will blink

ALARM OFF continually in this mode.

LO Alarm:

3. Press the LO ALARM SET key once. (You may have to first unlock the keys using

LOCK/UNLOCK). Press the UP and DOWN arrow key to select a value shown in the lower

left corner. A built-in safety feature will not allow you to select a LO alarm value less than

18%. Press the Lock key to save settings.

Testing the Alarms:

4. To test the alarms, unlock the controls by pressing the LOCK/UNLOCK key and then press

ALARM TEST key. The LO alarm followed by the HI alarm will blink and the audible

visual alarm will activate for about 1 second. Press LOCK key for normal operation.

5. To silence the alarm buzzer for 115 seconds press the alarm silence key.

Power OFF

To shut off the AX/MX300:

1. Press LOCK/UNLOCK to unlock the keypad.

2. Press I/O to turn the instrument off.

AX/MX300 Qui

ckstart Guide Rev 4 8/28//03

P/N A76029

Andere Handbücher für AX300

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Teledyne Messgerät Handbücher

Teledyne

Teledyne GFC7001T Bedienungsanleitung

Teledyne

Teledyne TIENet 360 LaserFlow Ex Betriebsanleitung

Teledyne

Teledyne BOSON+ CZ 14-75 Bedienungsanleitung

Teledyne

Teledyne HASTINGS Everywhereyoulook 200 Series Bedienungsanleitung

Teledyne

Teledyne 3000TA Installations- und Benutzerhandbuch

Teledyne

Teledyne T200 Bedienungsanleitung

Teledyne

Teledyne T3LVD Bedienungsanleitung

Teledyne

Teledyne T3LCR1002 Bedienungsanleitung

Teledyne

Teledyne 730 Bubbler Bedienungsanleitung

Teledyne

Teledyne 300 Bedienungsanleitung

Teledyne

Teledyne 6600 Bedienungsanleitung

Teledyne

Teledyne PEM-9004 Bedienungsanleitung

Teledyne

Teledyne T3SP Series Bedienungsanleitung

Teledyne

Teledyne T3SA3000-NFP Bedienungsanleitung

Teledyne

Teledyne Echotrac E20 Bedienungsanleitung

Teledyne

Teledyne 8800T Bedienungsanleitung

Teledyne

Teledyne PMAT 2000 Bedienungsanleitung

Teledyne

Teledyne 200E Bedienungsanleitung

Teledyne

Teledyne T3VNA Betriebsanleitung

Teledyne

Teledyne CEA 9001 Bedienungsanleitung

Teledyne

Teledyne HFM-301 Bedienungsanleitung

Teledyne

Teledyne T100 Bedienungsanleitung

Teledyne

Teledyne PS200-LMP Bedienungsanleitung

Teledyne

Teledyne 9110AH Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung