Teledyne T3SA3000-NFP Bedienungsanleitung

T3SA3000-NFP

Near Field Probe

User Manual

5 Commonwealth Ave

Woburn, MA 01801

Phone 781-665-1400

Toll Free 1-800-517-8431

Visit us at www.TestEquipmentDepot.com

This page is intentionally blank

OPERATING ENVIRONMENT

Before using the T3SA3000-NFP Probe kit, ensure that its operating environment will

be maintained within these parameters:

Temperature:5 to 40

Humidity:< 80% RH (non-condensing)

SAFETY REQUIREMENTS

CAUTION

To avoid personal injury or damage to the probes or any equipment connected to it,

review and comply with the following safety precautions.

•Use only as intended. The T3SA3000-NFP Probe kit is intended to be used

only with the compatible LeCroy instruments. Use of the probe kit and/or the

equipment it is connected to in a manner other than specied may impair the

protection mechanisms.

•Connect and disconnect properly. Avoid damage to cables through

excessive bending.

•Do not use in wet/damp or explosive atmospheres.

•For indoor use only. The test xture is intended for indoor use and should

be operated in a clean, dry, environment.

•Do not operate with suspected failures.

Do not use the product if any part is damaged.All maintenance should

be referred to qualied service personnel.

•Keep product surfaces clean and dry

Product Description

The T3SA3000-NFP probe set comprises of a set of four magnetic eld probes for

precompliance tests of printed circuit boards and other devices including

components, connectors, wiring, power supplies, etc.

The T3SA3000-NFP probe set is used to measure the magnetic elds in the area of

the device to determine the source and level of disturbance emissions.

The passive near eld probes are connected to the 50 Ohm input of a spectrum

analyser such as the Teledyne Test Tools T3SA3200 or T3SA3100, or to the input of

a high sensitivity oscilloscope such as the Teledyne LeCroy high denition 12 bit

HDO and WavePro HD families, or to a regular oscilloscope such as the Teledyne

Test Tools T3DSO range. The probes can also be used with other brands of spectrum

analyser or oscilloscope.

The probes can then make comparative measurements of magnetic elds and

disturbance currents in the frequency range from 30 MHz to 3 GHz.

Application

The probes are used to detect magnetic eld intensity and detect disturbance

emissions sources.

Spectrum Analyser

or Oscilloscope

DUT

T3SA3000-NFP

Near Field Probe

There are two methods of connecting the probes to the spectrum analyser or

oscilloscope, either directly or via a wideband preamplier (not supplied) as shown

above. If a wideband preamplier is used then ensure that the model chosen covers

the 30 MHz to 3 GHz bandwidth.

If the probes are used without a wideband preamplier, then set the spectrum

analyser input attenuation to 0dB and turn on the internal preamplier, if available on

your spectrum analyzer. Furthermore you can increase the dynamic range and

sensitivity by reducing frequency span, resolution bandwidth and video bandwidth.

If the probes are used with an oscilloscope then adjust the oscilloscopes’ input

sensitivity to give a suitable waveform amplitude on the oscilloscope display.

Note that if the spectrum analyser or oscilloscope does not cover the entire 3 GHz

bandwidth then the results will be limited by the bandwidth limit of the spectrum

analyser or oscilloscope.

Wideband

preamplier

Model Description Characteristics

The T3SA3000-NFP-1 can be used

at a distance of up to 10 cm from the

DUT. The probe detects the spatial

distribution of HF magnetic elds in

devices and assemblies and allows

the user to draw conclusions with

regard to disturbance emissions.

Frequency Range: 30 MHz to 3 GHz.

The T3SA3000-NFP-2 can be used

at a distance of up to 3 cm from the

DUT. Interference sources can be

localised by detecting the distribution

and orientation of the eld, therefore

enabling a more precise interference

source measurement and location.

Frequency Range: 30 MHz to 3 GHz.

The T3SA3000-NFP-3 detects the

current which generates the eld via

the magnetic eld circulating around

a single conductor or multiple

conductors. It is used for wide

conductor runs. Resolution is

approximately 5 mm. Frequency

Range: 30 MHz to 3 GHz.

The T3SA3000-NFP-4 is designed

for the detection of magnetic elds

which are emitted vertically from the

surface of the DUT and is ideal for

investigating current loops. The

probe can measure in conned

board areas Resolution is

approximately 3 mm. Frequency

Range: 30 MHz to 3 GHz.

T3SA3000-

NFP-1

T3SA3000-

NFP-4

T3SA3000-

NFP-3

T3SA3000-

NFP-2

Description of the individual probes

The T3SA3000-NFP kit comprises of:

1. Four Near Field Probes with SMB output connectors.

2. An SMB to SMA connecting cable.

3. An SMA to N Type adaptor.

Probe SMB Output Connectors

Sensing Four Near Field Probes

End

SMB to SMA Connecting Cable

SMA to N Type Adaptor

If the probes are to be used with an oscilloscope then a SMA to BNC adaptor may be

required (not supplied) since most oscilloscopes below 4 GHz use BNC input

connectors.

This page is intentionally blank

T3 stands for Teledyne Test Tools. 931422-00 RevA

Product brand or brand names are trademarks or requested trademarks of their respective holders.

Company Prole

Teledyne LeCroy is a leading provider of oscilloscopes, protocol

analyzers and related test and measurement solutions that

enable companies across a wide range of industries to design

and test electronic devices of all types. Since our founding in

1964, we have focused on creating products that improve

productivity by helping engineers resolve design issues faster

and more eectively. Oscilloscopes are tools used by

designers and engineers to measure and analyze complex

electronic signals in order to develop high-performance

systems and to validate electronic designs in order to improve

time to market.

The Teledyne Test Tools brand extends the Teledyne LeCroy

product portfolio with a comprehensive range of test

equipment solutions. This new range of products delivers

a broad range of quality test solutions that enable engineers to

rapidly validate product and design and reduce time-to-

market. Designers, engineers and educators rely on Teledyne

Test Tools solutions to meet their most challenging needs for

testing, education and electronics validation.

Location and Facilities

Headquartered in Chestnut Ridge, New York, Teledyne

Test Tools and Teledyne LeCroy has sales, service and

development subsidiaries in the US and throughout

Europe and Asia. Teledyne Test Tools and Teledyne LeCroy

products are employed across a wide variety of industries,

including semiconductor, computer, consumer electronics,

education, military/aerospace, automotive/industrial, and

telecommunications.

ABOUT TELEDYNE TEST TOOLS

Distributed by:

Test Equipment Depot - 800.517.8431 - 5 Commonwealth Ave, MA 01801

TestEquipmentDepot.com

Inhaltsverzeichnis

Andere Teledyne Messgerät Handbücher

Teledyne

Teledyne IR7000 Bedienungsanleitung

Teledyne

Teledyne T3SP Series Bedienungsanleitung

Teledyne

Teledyne Everywhereyoulook T3PM1100 Bedienungsanleitung

Teledyne

Teledyne EXPLORER Bedienungsanleitung

Teledyne

Teledyne 6750 Bedienungsanleitung

Teledyne

Teledyne CP Series Bedienungsanleitung

Teledyne

Teledyne 200E Bedienungsanleitung

Teledyne

Teledyne HASTINGS Everywhereyoulook 201 Series Bedienungsanleitung

Teledyne

Teledyne 4250 Betriebsanleitung

Teledyne

Teledyne Everywhereyoulook T3PM1100 Bedienungsanleitung

Teledyne

Teledyne 730 Bubbler Bedienungsanleitung

Teledyne

Teledyne 402R-EU Bedienungsanleitung

Teledyne

Teledyne WORKHORSE Kurzanleitung

Teledyne

Teledyne ADFM Pro20 Bedienungsanleitung

Teledyne

Teledyne GFC7001T Bedienungsanleitung

Teledyne

Teledyne AX300 Bedienungsanleitung

Teledyne

Teledyne HASTINGS 200 Series Bedienungsanleitung

Teledyne

Teledyne PS200 Series Handbuch

Teledyne

Teledyne T300 Bedienungsanleitung

Teledyne

Teledyne T102 Bedienungsanleitung

Teledyne

Teledyne PEM-9004 Bedienungsanleitung

Teledyne

Teledyne Echotrac E20 Bedienungsanleitung

Teledyne

Teledyne 465M Bedienungsanleitung

Teledyne

Teledyne TIENet 360 LaserFlow Ex Betriebsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung