Telit Wireless Solutions WE310F5-X Bedienungsanleitung

1VV0301698 2021-01 Rev.0

Telit Technical Documentation

WE310F5-X IP2WiFi Legacy

Command

Reference Guide

80664ST11079A Rev. 3 –2021-10-25

WE310F5-X IP2WiFi Legacy AT Command Reference Guide

80664ST11079A Rev. 3 Page 2 of 79 2021-10-25

Not Subject to NDA

APPLICABILITY TABLE

PRODUCTS

WE310F5-I

WE310F5-P

 
 
 WE310F5-X IP2WiFi Legacy AT Command Reference Guide 
 
80664ST11079A Rev. 3 Page 3 of 79 2021-10-25 
 
 
Not Subject to NDA 
Contents 
APPLICABILITY TABLE 2 
CONTENTS 3 
1. INTRODUCTION 7 
 Scope 7 
 Audience 7 
 Contact Information, Support 7 
 Symbol Convention 7 
 Related Documents 8 
2. OVERVIEW 9 
 AT Commands 9 
2.1.1. AT Command Definitions 9 
2.1.2. AT Command Syntax 10 
3. GETTING STARTED 11 
 System Overview 11 
 Legacy Command Mode 11 
4. ARCHITECTURE 12 
 Working Principle 12 
 System Initialization 12 
 Data Handling 13 
4.3.1. Bulk Data Tx and Rx 15 
4.3.2. Hardware Flow Control 15 
 Serial Data Handling 15 
 Wireless Network Management 16 
4.5.1. Scanning 16 
4.5.2. Association 16 
4.5.3. SSID and Passphrase 16 
5. HOST INTERACTION 18 
 Interface 18 
5.1.1. Hardware Flow Control 18 
5.1.2. Interface Verification 18 

 
 
 WE310F5-X IP2WiFi Legacy AT Command Reference Guide 
 
80664ST11079A Rev. 3 Page 4 of 79 2021-10-25 
 
 
Not Subject to NDA 
6. GENERAL OPERATIONS 20 
 Version 20 
 System Settings 22 
6.2.1. Get Current Command Mode Status 22 
6.2.2. Switch Between Legacy and New AT Command 22 
6.2.3. Boot Reason 23 
 Time Setting 24 
6.3.1. Set System Time 24 
6.3.1.1. Manual Setting 24 
6.3.2. Get System Time 25 
 Profile Setting 26 
6.4.1. Get Profile 26 
6.4.2. Save Profile 27 
6.4.3. Load Profile 28 
6.4.4. Select Default Profile 28 
6.4.5. Define Profile 29 
6.4.6. Restore Profile 30 
6.4.7. Identification Information 31 
 Enhanced Asynchronous Notification 32 
 Reset 33 
 MAC 34 
6.7.1. Get MAC Address 34 
 Package Version 35 
7. WIRELESS 37 
 Wireless Generic 37 
7.1.1. Regulatory Domain 37 
7.1.1.1. Set Regulatory Domain 37 
7.1.1.2. Get Regulatory Domain 37 
7.1.2. Operation Mode 38 
7.1.3. PHY Mode 40 
7.1.3.1. Set PHY Mode 40 
7.1.3.2. Get PHY Mode 41 
 Station/AP Mode 41 

 
 
 WE310F5-X IP2WiFi Legacy AT Command Reference Guide 
 
80664ST11079A Rev. 3 Page 5 of 79 2021-10-25 
 
 
Not Subject to NDA 
2.1. Scan Time Settings 41 
2.1.1. Set Scan Time 41 
2.1.2. Get Scan Time 42 
2.2. Security Configuration 43 
2.2.1. Security Setting 43 
2.2.2. WPA-PSK and WPA2-PSK Passphrase 44 
2.2.3. WPA-PSK and WPA2-PSK Key Calculation 45 
2.2.4. WPA-PSK and WPA2-PSK Key 46 
2.3. Scanning 47 
2.4. Association 49 
2.5. Disassociation 51 
2.6. WLAN Keep Alive Interval 52 
DATA TRANSFER 53 
 Auto Mode 53 
1.1. Enable Auto Connection 53 
 Enable Multicast Reception 53 
POWER MANAGEMENT –RADIO AND SYSTEM 56 
 Radio Receive Settings 56 
1.1. Active Radio Receive 56 
1.2. Standard Power Save Radio Receive based on DTIM/Listen 
Interval 57 
1.2.1. IEEE PS Poll Listen Interval 57 
1.3. Custom Power Save Radio Receive 60 
 System Power Save 61 
2.1. Standby 61 
2.2. Deep Sleep 63 
PRODUCTION AND DEBUG 66 
 Debug 66 
1.1. LogLevel 66 
1.2. Echo 67 
1.3. Verbose 68 
1.4. RSSI 68 
1.5. WLAN Status 69 

WE310F5-X IP2WiFi Legacy AT Command Reference Guide

80664ST11079A Rev. 3 Page 6 of 79 2021-10-25

Not Subject to NDA

11. APPENDIX A - RESPONSE CODES 71

Synchronous Message 71

Asynchronous & Enhanced Asynchronous Messages 71

12. PRODUCT AND SAFETY INFORMATION 73

Copyrights and Other Notices 73

12.1.1. Copyrights 73

12.1.2. Computer Software Copyrights 73

Usage and Disclosure Restrictions 74

12.2.1. License Agreements 74

12.2.2. Copyrighted Materials 74

12.2.3. High Risk Materials 74

12.2.4. Trademarks 74

12.2.5. Third Party Rights 75

12.2.6. Waiwer of Liability 75

Safety Recommendations 75

13. GLOSSARY 77

14. DOCUMENT HISTORY 78

WE310F5-X IP2WiFi Legacy AT Command Reference Guide

80664ST11079A Rev. 3 Page 7 of 79 2021-10-25

Not Subject to NDA

1. INTRODUCTION

Scope

This document is aimed in providing a detailed specification on and a comprehensive

listing as a reference for the whole set of AT command supported by the WE310F5-X

module in legacy command mode.

Audience

This document is intended for Telit customers, who are integrators, about to implement

their applications using our WE310F5-X modules.

To use this document effectively, you should be already familiar with Telit modules and

their ease of controlling by means of AT Commands.

Contact Information, Support

For general contact, technical support services, technical questions and report

documentation errors contact Telit Technical Support at:

•

TS[email protected]

Alternatively, use:

http://www.telit.com/support

For detailed information about where you can buy the Telit modules or for

recommendations on accessories and components visit

http://www.telit.com

Our aim is to make this guide as helpful as possible. Keep us informed of your comments

and suggestions for improvements.

Telit appreciates feedback from the users of our information.

Symbol Convention

Table 1: Symbol Convention.

Danger: This information MUST be followed, or catastrophic

equipment failure or personal injury may occur.

Warning: Alerts the user on important steps about the module

integration.

WE310F5-X IP2WiFi Legacy AT Command Reference Guide

80664ST11079A Rev. 3 Page 8 of 79 2021-10-25

Not Subject to NDA

Note/Tip: Provides advice and suggestions that may be useful when

integrating the module.

Electro-static Discharge: Notifies the user to take proper grounding

precautions before handling the product.

All dates are in ISO 8601 format, that is. YYYY-MM-DD.

Related Documents

Table 2: Related Documents.

Module Name

Description

1VV0301580

WE310F5-I/P Wi-Fi/BLE Module HW User Guide

1VV0301594

WE310F5-I/P EVB User Guide

1VV0301569

WE310F5-I/P Evaluation Board Quick Start Guide

WE310F5-X IP2WiFi Legacy AT Command Reference Guide

80664ST11079A Rev. 3 Page 9 of 79 2021-10-25

Not Subject to NDA

2. OVERVIEW

AT Commands

The Telit wireless module family can be controlled via the serial interface using the

standard AT commands.

2.1.1. AT Command Definitions

This document uses the following syntactical definitions:

1. Special text fonts represent particular commands, keywords, variables, or

window sessions

2. Color text indicates cross-reference hyper links to supplemental information

3. Command notation indicates commands, subcommands, or command elements

Following table describes the text conventions used in this manual for software

procedures that are explained using the AT command line interface.

Table 3: Command Definition.

Convention Type

Description

[ ]

Square brackets

Enclose optional parameters. Choose none; or select one or more an unlimited

number of times each. Do not enter brackets as part of any command.

[parm1|parm2|parm3]

Question mark

Used with the square brackets to limit the immediately following token to one

occurrence

<CR>

Carriage return

Each command is terminated by a carriage return.

<LF>

Line feed

Each command is terminated by a line feed.

Carriage return Line feed

Each response is started with a carriage return and line feed with some

exceptions.

< >

Angle brackets

Enclose a numeric range, endpoints inclusive. Do not enter angle brackets as

part of any command.

<SSID>

Equal sign

Separates the variable from explanatory text. Is entered as part of the

command.

PROCESSID = <CID>

dot (period)

Allows the repetition of the element that immediately follows it multiple times.

Do not enter as part of the command.

.AA:NN can be expanded to 1:01 1:02 1:03.

A.B.C.D

IP address

IPv4-style address.

10.0.11.123

WE310F5-X IP2WiFi Legacy AT Command Reference Guide

80664ST11079A Rev. 3 Page 10 of 79 2021-10-25

Not Subject to NDA

Convention Type

Description

LINE

End-to-line input token

Indicates user input of any string, including spaces. No other parameters may

be entered after input for this token.

string of words

WORD

Single token

Indicates user input of any contiguous string (excluding spaces).

singlewordnospaces

2.1.2. AT Command Syntax

Following table describes the syntax rules followed by Telit implementation used in this

document for software procedures that are explained using the AT command line

interface.

Table 4: Command Syntax.

Convention Type

Description

command syntax monospaced font

This monospaced font represents command strings entered on a command line

and sample source code.

AT XXXX

Proportional font description

Gives specific details about a parameter.

<Data> DATA

UPPERCASE

Variable parameter

Indicates user input. Enter a value according to the descriptions that follow.

Each uppercased token expands into one or more other token.

lowercase

Keyword parameter

Indicates keywords. Enter values exactly as shown in the command description.

Inhaltsverzeichnis

Andere Telit Wireless Solutions Drahtlosmodul Handbücher

Telit Wireless Solutions

Telit Wireless Solutions xE70-915 Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SE868SY-D Leitfaden

Telit Wireless Solutions

Telit Wireless Solutions UL865 Series Leitfaden

Telit Wireless Solutions

Telit Wireless Solutions SL869-V3 EVK Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions ME310G1 Leitfaden

Telit Wireless Solutions

Telit Wireless Solutions LN920 TLB Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions GL865-DUAL V3 Installationshandbuch

Telit Wireless Solutions

Telit Wireless Solutions LE50-868 Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions WE866C Series Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions FN990 TLB Leitfaden

Telit Wireless Solutions

Telit Wireless Solutions LE910-SKG Installationshandbuch

Telit Wireless Solutions

Telit Wireless Solutions WE310F5-I Installationshandbuch

Telit Wireless Solutions

Telit Wireless Solutions ME910C1 Series Montage- und Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions LN920 Leitfaden

Telit Wireless Solutions

Telit Wireless Solutions UC864-G Installationshandbuch

Telit Wireless Solutions

Telit Wireless Solutions SE868SY-D Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions ME910C1 Series Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions WE865-DUAL Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions LM940 Leitfaden

Telit Wireless Solutions

Telit Wireless Solutions WE310F5-I Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-V2 Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions ME910G1 Leitfaden

Telit Wireless Solutions

Telit Wireless Solutions ME310G1-W1 Leitfaden

Telit Wireless Solutions

Telit Wireless Solutions LE910C series Installationshandbuch

Beliebte Drahtlosmodul Handbücher anderer Marken

Laird

Laird RM024 Bedienungsanleitung

Laird

Laird BT830-SA Kurzanleitung zur Einrichtung

Ebyte

Ebyte E49-400T20S Bedienungsanleitung

Fibocom

Fibocom FM101-NA-20 Montageanleitung

Waldmann

Waldmann EnOcean TALK MODUL G2 Bedienungsanleitung

Smartech

Smartech LBT-1.DO4 Bedienungsanleitung

Cooper Wiring Devices

Cooper Wiring Devices ESPIRE RF RFAPM Bedienungsanleitung

Yuga

Yuga CLM920 Bedienungsanleitung

Waldmann

Waldmann TALK Bluetooth Bedienungsanleitung

Ebyte

Ebyte E07-900M10S Bedienungsanleitung

Quectel

Quectel SC690A Series Beilage

Panasonic

Panasonic INDUSTRY PAN9028 Kurzanleitung zur Einrichtung

Ebyte

Ebyte E70-433NW30S Bedienungsanleitung

LongSung Technology

LongSung Technology U9507E Bedienungsanleitung

Wistron NeWeb

Wistron NeWeb DNUR-S2 Bedienungsanleitung

Ebyte

Ebyte E49-400M20S4 Bedienungsanleitung

RF-Star

RF-Star SimpleLink RF-BM-2652P1 CC2652P Bedienungsanleitung

Ebyte

Ebyte E18-TBH-27 Bedienungsanleitung