Teltonika FM1110 Bedienungsanleitung
1
FM1110 and FM1120 Sample User Guide for
Recommended Configuration
1About the document
This document contains information required for fast testing of the FM1110 and FM1120 device.
1.1
Getting started with FM1110 and FM1120 device
This paragraph contains the information needed to successfully launch and use the FM1110 and
FM1120 device. The steps below should be followed carefully to completely test the FM1110 and
FM1120.
1.2
SIM card insert scheme
Gently open FM1110 or FM1120 case using screwdrivers
1
2
3
4
2
Remove FM1110 or FM1120 case
Insert SIM card as shown
Attach top housing cover
Device is ready
1.3
Power source connection
Picture 2. 2x5 socket pin out
DIN 1 (IGNITION)
5
10
Ucc_DALLAS
DIN 2
4
9
DIN 3
DOUT 1
3
8
DATA_DALLAS
DOUT 2
2
7
AIN 1
VCC (1030)V DC(+)
1
6
GND(VCC(1030)V DC)(-)
3
1.4
Installing FM1110 and FM1120 drivers
Software requirements
• Operating system 32-bit and 64-bit: Windows XP with SP3 or later, Windows Vista, Windows 7.
• MS .NET Framework V3.5 or later (http://www.microsoft.com or
http://avl1.teltonika.lt/downloads/tavl/Framework/dotnetfx35setupSP1.zip).
Drivers
Please download Virtual COM Port drivers from Teltonika website:
http://avl1.teltonika.lt/downloads/FM11/vcpdriver_v1.3.1_setup.zip
Installing drivers
Extract and run VCPDriver_V1.3.1_Setup.exe. This driver is used to detect FM1110 or
FM1120 device connected to the computer. Click 'Next' in driver installation window (figures
below):
Figure 3. Driver installation window
This will launch device driver installation wizard. In the following window click ‘Next’ button
again:
Figure 4. Driver installation window
4
Setup will continue installing drivers and will display a window about successful process in the end.
Click 'Finish' to complete setup:
Figure 5. Driver installation window
You have now installed drivers for FM1110 and FM1120 device successfully.
Power source connection
Note, that FM1110 and FM1120 cannot be powered via USB cable, so the external
10...30 V DC (1,2 W Max) power supply must be used to power up the device.
1.5
Placing of device
FM1110 and FM1120 must be placed sticker on TOP (please refer picture below)
It’s forbidden to place ON1110 under metal surfaces.
It’s recommended to place FM1110 and FM1120 device far from car radio, speakers or alarm
systems.
FM1110 and FM1120 must be placed so its state is as horizontal as possible
It is recommended to place FM1110 and FM1120 behind dashboard as close to the window as
possible. A good example of GNSS antenna placement is displayed in a picture below (area colored
green).
5
Figure 6 Correct placement of FM1110 and FM1120
1.6
Loading the Configuration into the FM1110 and FM1120 Devices
FM1110 and FM1120 Configurator must be used to configure the FM1110 and FM1120
device. The only data client is required to enter to configuration is APN data, domain and target server
port.
6
Picture 7. Recommended configuration view
1.6.1 APN configuration
In order to FM1202 device to be able to connect to local GPRS network (and send AVL data)
the following APN data (provided by local GSM services provider) must be entered into FM1202
configuration (1 selection):
Access Point Name (APN) with authentication type CHAP or PAP (if required);
APN login;
APN password;
If you are not sure what APN settings should be, ask your GSM operator.
1.6.2 Domain and Port configuration
In field which is market as number 2 you have to enter your server IP address, where to send
FM AVL data.
7
In field which is marked as number 3 you have to enter Port number. In recommended
configuration mode transfer protocol - TCP. But also you can set UDP transfer protocol in advanced
configuration.
1.6.3 Saving the Configuration into the FM1110 and FM1120 Device
Follow these steps:
1. Press connect in configurators navigation bar ( make sure that your FM1202 is connected to PC
and power source).
Picture 8. Connecting FM1202 to configurator
2. When device is to connected to configurator you can save your configuration by clicking Save.
Picture 9. Saving configuration to FM1202 device
1.6.4 Recommended Configuration
Recommended configuration is based on fast periodic AVL data acquisition mainly according
to the change of the object’s geographic angle (Min.Angle = 10 degrees). According to this
configuration the FM1110 and FM1120 device will generate AVL record every time the object’s angle is
changed more than 10 degrees. Such AVL data acquisition is rational in cases the object mostly moves
in the city. Min.Distance = 100 meters, so the additional AVL record will be generated after driving
more than 100 meters in the straight line. If the object with FM1110 and FM1120 device is not moving,
the AVL data records are generated periodically every 1 hour (Vehicle on STOP Min.period = 3600 s).
If the object with FM1110 and FM1120 device is moving, the AVL data records are generated
periodically every 300 seconds.
AVL data is sent via GPRS to the server as soon as the AVL data record is generated (Min.
saved records = 1; Send period = 1 s). According to this configuration one AVL data record,
containing information about the GPS position and Input/Output (I/O) parameters is sent to the
server at least every 300 seconds.
Following I/O elements’ vales are monitored in every AVL data record:
DIN1 (as ignition) {values: 0 –Off; 1 –On};
Movement {values: 0 –object is not moving; 1 –object is moving};
Power voltage {values: from 10 V to 30 V, according to the power source).
8
Speed {values: current vehicle speed in km/h}
Additional AVL data records called “events” are generated on following parameter value
changes:
If power voltage value falls to less than 11 V;
Speed is less than 5 km/h for more than 1 minute;
Ignition is turned ON/OFF (DIN1=1 or DIN1=0).
1.6.5 What is the purpose of testing FM1110 and FM1120 in this scenario?
The main purpose of this testing scenario is for the user to see the highly detailed track (as in
the sample screenshot below) of his driven track in the city. The user will be able to see his vehicles
current position as well as the position in any selected time in the past. The user will be able to see the
time and points in the map in which the ignition has been turned ON/OFF, power voltage has become
less than 11 V (car battery needs to be recharged). The user will be able to compare “Vehicle on
STOP” and “Vehicle MOVING” modes.
Picture 10. Track of the FM1110 and FM1120 working in "Recommended Configuration"
9
The track showed in the screenshot above contains the information of 3 days driving of real vehicle in
the city of Vilnius, Lithuania. Using the service of local GSM service provider “Bite GSM” 1 MB of
data has been transmitted through the GPRS to generate such track.
NOTE, that GPRS traffic differs from the GPRS coverage at the area and the GSM
service provider’s data averaging policy, so the GPRS traffic can be higher than the
described in the example above.
Andere Handbücher für FM1110
2
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Teltonika GPS Handbücher
Teltonika
Teltonika FMC00A Installationsanleitung
Teltonika
Teltonika FMB920 Bedienungsanleitung
Teltonika
Teltonika FMB225 Bedienungsanleitung
Teltonika
Teltonika FMB140 Installationsanleitung
Teltonika
Teltonika FMB001 Installationsanleitung
Teltonika
Teltonika FMB920 Bedienungsanleitung
Teltonika
Teltonika FM4200 Bedienungsanleitung
Teltonika
Teltonika FMB900 Bedienungsanleitung
Teltonika
Teltonika FMB130 Bedienungsanleitung
Teltonika
Teltonika FM1010 Bedienungsanleitung
Teltonika
Teltonika FMC800 Bedienungsanleitung
Teltonika
Teltonika FMB122 Installationsanleitung
Teltonika
Teltonika FMA120 Bedienungsanleitung
Teltonika
Teltonika FMA202 Bedienungsanleitung
Teltonika
Teltonika FM1100 Bedienungsanleitung
Teltonika
Teltonika FMB910 Installationsanleitung
Teltonika
Teltonika FMB125 Installationsanleitung
Teltonika
Teltonika FMU130 Bedienungsanleitung
Teltonika
Teltonika FMM00A Installationsanleitung
Teltonika
Teltonika TMT250 Installationsanleitung
