Tennant 6080 Schulungshandbuch

IB340068 (9-99)LITHOIN U.S.A.1

No.340068

Machine:6080/3640

Published:9-99/01

INSTRUCTION BULLETINSystem:SWEEPING

NOTE:DONOTDISCARD thePartsList fromtheInstruction Bulletin.Place theParts

Listinthe appropriateplace inyourmachinemanualforfuturereference.

Retaining thePartsListwill make iteasiertoreorderindividualparts and will

save you the costofordering anentire kit.

NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.

Installation Instructions for Kit number 80302

SYNOPSIS/PROBLEM:

This kit contains the parts needed to install a new side brush lift cable on the model 6080

and 3640 sweepers. Please follow step-by-step instructions.

SPECIAL TOOLS/CONSIDERATIONS:None

(Estimated time to complete: 2 hour)

INSTALLATION:

(Referto FIG.1,2 and 3)

FORSAFETY:Beforeleaving orservicing machine,stop on levelsurface and setparking

brake.Thenturn off machine and remove key.

1. Remove the filter cover from the rear of the machine. Remove the handle stop bracket

from the upper/left side of the filter compartment. (RefertoFIG.1)

2. Pull up on the two handle locks and move the handle assembly to its lowest position.

(RefertoFIG.3)

(1)

FIG.1-- CoverPlateAnd Handle

3. Remove the three hex screws holding the cover plate to the inside of the right side handle

tower. Remove the cover plate from the machine. (RefertoFIG.1)

4. Remove the bolt holding the pivot plate to the plastic side arm. This will allow the plate and

handle assembly to be pulled away from the plastic arm for easy access. (RefertoFIG.1)

IB340068 (9-99)LITHOIN U.S.A.2

5. Remove the cotter pin and clevis pin from the end of the side brush lift cable where it

attaches to the side brush lift lever. (RefertoFIG.1)

6. Remove the nut from the clamp holding the side brush cable to the mount plate.

(RefertoFIG.1)

7. Remove the debris hopper from the machine.

8. Locate the side brush lower mount bracket on the right side of the frame, near the right

front caster. (RefertoFIG.2)

9. Remove the two hex screws holding the side brush lower mount bracket to the machine

frame. (RefertoFIG.2)

FIG.2-- SideBrushBracketAnd Cable

10.Pull the mount bracket out of the hole in the frame. Pull the side brush cable out of mount

slot. (RefertoFIG.2)

11.Remove the two hex screws holding the side brush lift cable spring assembly to the right side

of the machine frame, out near the right side brush. (RefertoFIG.2)

12.Pull the spring and cable assembly out of the machine frame. (RefertoFIG.3)

13.Remove the clevis pin holding the side brush lift cable to the spring assembly. Remove the

side brush lift cable from the spring assembly. (RefertoFIG.3)

14.Route the new lift cable (1) down the handle assembly, thru the hole in the handle, into the

hole in the main frame, and down to the right side of the frame. Next, reach in the frame

hole and grab the cable.

NOTE: Add the cable tie (2) around the new side brush cable (1) and the existing stiff

main brush lift cable. This will prevent the new side brush lift cable from drooping down

and rubbing on the brush drive pulley.

15.Reconnect the cable to the side brush spring assembly. Reinstall the spring assembly on the

frame. Tighten the two hex screws to 7.6 -- 9.9 Nm (6 -- 8 ft lb). (RefertoFIG.3)

16.Position the side brush lift cable in the slot on the lower mount bracket. Reinstall the lower

mount bracket in the machine. Tighten the two hex screws to 8 -- 24Nm (15 -- 20 ft lb).

(RefertoFIG.2)

IB340068 (9-99)LITHOIN U.S.A.3

17.Go up to the main brush lift lever and install the nut on the main brush lift cable mount clamp.

Tighten the nut to 7.6 -- 9.9 Nm (6 -- 8 ft lb). (RefertoFIG.1)

18.Install the clevis pin and cotter pin in the end of the new cable where it attaches to the main

brush lift lever. (RefertoFIG.1)

19.Reinstall the right side handle assembly cover plate. Tighten the three hex screws to

18 -- 24 Nm (15 -- 20 ft lb). (RefertoFIG.1)

(1)

FIG.3-- CableAssemblyAnd Stop Bracket

20.Move the handle assembly up to one of the four adjustment holes.

21.Reinstall the filter cover and the handle stop bracket. (RefertoFIG.3)

22.Reinstall the hopper.

23.Start the machine and check the side brush lift cable for proper operation.

24.Close the machine cover.

BILL OFMATERIALSFORSIDEBRUSH CABLEKIT80302

TENNANT

Ref.PartNo.Description Qty.

1 80191 Side brush cable 1

2 49266 Cable tie 1

TENNANT COMPANY

P. O. Box 1452

Minneapolis, MN 55440-1452

Andere Handbücher für 6080

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Tennant Bodenreinigungsmaschine Handbücher

Tennant

Tennant 515SS Bedienungsanleitung

Tennant

Tennant 1530 Produkthandbuch

Tennant

Tennant 5680 Bedienungsanleitung

Tennant

Tennant 1240 Bedienungsanleitung

Tennant

Tennant 6400 Bedienungsanleitung

Tennant

Tennant 1180 Produkthandbuch

Tennant

Tennant 6400 Bedienungsanleitung

Tennant

Tennant T7 Bedienungsanleitung

Tennant

Tennant 1550 Produkthandbuch

Tennant

Tennant S9 Produkthandbuch

Tennant

Tennant IRIS T300 Bedienungsanleitung

Tennant

Tennant T5 Bedienungs- und Montageanleitung

Tennant

Tennant 1140 607681 Produkthandbuch

Tennant

Tennant 1186E Bedienungsanleitung

Tennant

Tennant 800D Bedienungsanleitung

Tennant

Tennant 450 Bedienungsanleitung

Tennant

Tennant ATLV 4300 Bedienungsanleitung

Tennant

Tennant 1200 Produkthandbuch

Tennant

Tennant E5 Bedienungsanleitung

Tennant

Tennant 2510 Bedienungsanleitung

Tennant

Tennant 240 Bedienungsanleitung

Tennant

Tennant Castex SCX-400 Produkthandbuch

Tennant

Tennant 5700 Bedienungsanleitung

Tennant

Tennant T7 Bedienungsanleitung

Beliebte Bodenreinigungsmaschine Handbücher anderer Marken

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Bedienungsanleitung

Numatic

Numatic ET 4045 Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Bedienungsanleitung

Mytee

Mytee 8070 Mytee-Lite Bedienungsanleitung

Kärcher

Kärcher B 140 R Bedienungsanleitung

Triple S

Triple S Ace 26T1 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SW 750 Bedienungsanleitung

Tornado

Tornado Marathon 2000 98190 Handbuch

Windsor

Windsor ADMIRAL Admiral 8 Bedienungsanleitung

Numatic

Numatic TTB 1117/100 Bedienungsanleitung

Nobles

Nobles Frontier Produkthandbuch

lavina

lavina 21-X Bedienungsanleitung

KENT

KENT Edge 28B Bedienungsanleitung

Windsor

Windsor BDP 51/2000C Bedienungsanleitung

CleanFreak

CleanFreak DURA-18HD Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Administratorhandbuch

BETCO

BETCO PB24 Bedienungsanleitung

IPC

IPC CT51-71 BT Bedienungsanleitung