Tennant EX-CAN-10 Bedienungsanleitung

9007550

Rev. 00 (04-2010)

*9007550*

E X -- C A N -- 1 0

Operator Manual EN

Manual del Operario ES

Manuel Opérateur FR

www.nobles.com

www.tennantco.com

Model Part No.:

9007622 - EX-CAN-10 (120V)

Portable Carpet Extractor

Extractor Portátil de Alfombras

Extracteur de moquette

EN OPERATION

EX--CAN--10 (04--10)

This manual is furnished with each new model.

It provides necessary operation and maintenance

instructions.

Read this manual completely and understand the

machine before operating or servicing it.

This machine will provide excellent service. However,

the best results will be obtained at minimum costs if:

SThe machine is operated with reasonable care.

SThe machine is maintained regularly - per the

machine maintenance instructions provided.

SThe machine is maintained with

manufacturer--supplied or equivalent parts.

Parts and supplies may be ordered online, by phone,

byfaxorbymail.

UNCRATING MACHINE: Carefully check carton for

signs of damage. Report damages at once to carrier.

PROTECT THE ENVIRONMENT

Please dispose of packaging materials

and old machine components in an en-

vironmentally safe way according to lo-

cal waste disposal regulations.

Always remember to recycle.

Tennant Company

PO Box 1452

Minneapolis, MN 55440 USA

Phone: (800) 553--8033 or (763) 513--2850

www.tennantco.com

www.nobles.com

Specifications and parts are subject to change without notice.

MACHINE DATA

Please fill out at time of installation

for future reference.

Model No. --

Serial No. --

Machine Options --

Sales Rep. --

Sales Rep. phone no. --

Customer Number --

Installation Date --

TABLE OF CONTENTS

SAFETY PRECAUTIONS 3....................

SAFETY LABEL 4............................

MACHINE COMPONENTS 5...................

UNPACKING THE MACHINE 6.................

MACHINE SETUP 6..........................

MACHINE OPERATION 7.....................

DRAINING TANKS 8..........................

MACHINE MAINTENANCE 9..................

STORING MACHINE 11........................

RECOMMENDED STOCK ITEMS 11.............

TROUBLE SHOOTING 11......................

SPECIFICATIONS 12..........................

MACHINE DIMENSIONS 12....................

OPERATION EN

EX--CAN--10 (04--10)

SAFETY PRECAUTIONS

This machine is intended for commercial use only.

It is designed exclusively to clean carpet and

upholstery in an indoor environment and is not

constructed for any other use. Use only

recommended cleaning solutions and accessory

tools.

All operators must read, understand and practice

the following safety precautions.

The following warning alert symbol and the “FOR

SAFETY” heading are used throughout this manual as

indicated in their description:

WARNING: To warn of hazards or unsafe

practices which could result in severe personal

injury or death.

FOR SAFETY: To identify actions which must be

followed for safe operation of equipment.

Failure to follow these warnings may result in:

personal injury, electrocution, electric shock, fire

or explosion:

WARNING: Do Not Use Flammable Liquids Or

Operate Machine In Or Near Flammable Liquids,

Vapors Or Combustible Dusts.

WARNING: Do Not Pick Up Flammable

Materials Or Reactive Metals.

WARNING: Do Not Operate With Damaged

Power Cord. Do Not Modify Plug. Unplug Power

Cord Before Servicing Machine.

WARNING: Do Not Use Outdoors. Do Not

Expose to Rain. Store Indoors.

The following information signals potentially

dangerous conditions to the operator or

equipment:

FOR SAFETY:

1. Do not operate machine:

-- Unless trained and authorized.

-- Unless operator manual is read and

understood.

-- In flammable or explosive areas.

-- Unless cord is properly grounded.

-- With damaged cord or plug.

-- If not in proper operating condition.

-- In outdoor areas.

-- In standing water.

-- With the use of additional extension cords.

Only use manufacturer’s extension cord

equipped with machine which has proper

capacity and is grounded.

2. Before operating machine:

-- Make sure all safety devices are in place

and operate properly.

3. When using machine:

-- Do not run machine over cord.

-- Do not pull machine by plug or cord.

-- Do not pull cord around sharp edges or

corners.

-- Do not close doors on cord.

-- Do not unplug by pulling on cord.

-- Do not stretch cord.

-- Do not handle plug with wet hands.

-- Keep cord away from heated surfaces.

-- Report machine damage or faulty operation

immediately.

-- Follow mixing and handling instructions on

chemical containers.

4. Before leaving or servicing machine:

-- Turn off machine.

-- Unplug cord from wall outlet.

5. When servicing machine:

-- Unplug cord from wall outlet.

-- Avoid moving parts. Do not wear loose

jackets, shirts, or sleeves.

-- Use manufacturer supplied or approved

replacement parts.

EN OPERATION

EX--CAN--10 (04--10)

GROUNDING INSTRUCTIONS

Machine must be grounded. If it should

malfunction or breakdown, grounding provides a

path of least resistance for electrical current to

reduce the risk of electrical shock. This machine is

equipped with a cord having an

equipment--grounding conductor and grounding

plug. The plug must be plugged into an

appropriate outlet that is properly installed in

accordance with all local codes and ordinances.

Do not remove ground pin; if missing, replace plug

before use.

Grounded

3HoleOutlet

Ground Pin

SAFETY LABEL

The safety label appears on the machine in the location

indicated. Replace label if it becomes damaged or

illegible.

OPERATION EN

EX--CAN--10 (04--10)

MACHINE COMPONENTS

16 13

1. Machine Lift Handle

2. Solution Tank

3. Recovery Tank

4. Lockable Casters

5. 254mm (10 in) Stair Climbing Wheels

6. Bottle Holder

7. Main Power ON/OFF Switch

8. Power Supply Cord Pigtail

9. Recovery Tank Drain Hose

10. Accessory Tool Solution Hose Hookup

11. Accessory Tool Vacuum Hose Hookup

12. 4.6m (15 ft) Vacuum Hose

13. 4.6m (15 ft) Solution Hose

14. 330mm (13 in) Floor Tool (optional)

15. 7.6m (25 ft) Power Supply Cord

16. 1.4m (4 1/2 ft) Clean--Out Hose

EN OPERATION

EX--CAN--10 (04--10)

UNPACKING THE MACHINE

1. Carefully check carton for signs of damage. Report

damages to carrier immediately.

2. Check carton contents for to ensure carton is

complete. Contact distributor for missing items.

1 -- Machine

1 -- 1.4M (4 1/2 ft.) Clean--out Vacuum Hose

1 -- 4.6m (15 ft) Vacuum Hose

1 -- 4.6m (15 ft) Solution Hose

1 -- 7.6m (25 ft) Power Supply Cord

MACHINE SETUP

1. Remove solution tank lid. Using a hose or bucket,

fill tank with 38L (10 gal) of hot water, 60°C (140°F)

maximum (Figure 1).

ATTENTION: Use different buckets to fill and drain

machine to prevent solution system clogs.

FIG. 1

WARNING: Do Not Use Flammable Liquids Or

Operate Machine In Or Near Flammable Liquids,

Vapors Or Combustible Dusts.

2. Add a recommended cleaning solution to the

proper dilution ratio.

FOR SAFETY: When using machine, follow mixing

and handling instructions on chemical containers.

ATTENTION: If using powdered cleaning

chemicals, mix chemical with water prior to adding

to the tank.

NOTE: If desired, water alone achieves excellent

cleaning results.

3. Replace solution tank lid after filling.

4. Connect the vacuum hose to the vacuum inlet tube

located at the rear of machine. Then connect the

solution hose to quick coupler located below handle

(Figure 2).

FIG. 2

5. Attach accessory tool to opposite end of hoses

(Figure 3).

FIG. 3

6. If desired, lock the front casters to keep machine

stationary while cleaning (Figure 4).

FIG. 4

OPERATION EN

EX--CAN--10 (04--10)

7. Connect the power supply cord to machine. Then

plug cord into a grounded wall outlet (Figure 5).

Grounded

3HoleOutlet

Ground Pin

FIG. 5

FOR SAFETY: Do not operate machine unless cord

is properly grounded.

FOR SAFETY: Do not operate machine with the

use of additional extension cords. Only use

manufacturer’s extension cord equipped with

machine which has proper capacity and is

grounded.

MACHINE OPERATION

FOR SAFETY:Do not operate machine unless

operator manual is read and understood.

PRE--OPERATION

1. Vacuum carpet to remove particles and other

debris.

2. Inspect power cord for damage. Replace cord if

damaged.

OPERATING FLOOR TOOL

WARNING: Do Not Pick Up Flammable

Materials Or Reactive Metals.

1. Turn the Main Power switch to the ON position

(Figure 6).

FIG. 6

2. Place the floor tool so the stainless steel shoes are

parallel to the floor. Squeeze the trigger and apply

a downward pressure on the floor tool head and

slowly pull the tool backwards. Release trigger

150mm (6 in) from end of stroke (Figure 7).

3. Push the floor tool forward over the same path with

trigger released when returning to the next stroke.

Continue this pull and push method with a 50mm (2

in) overlap for each stroke.

NOTE: For heavily soiled areas, repeat stroke or

change angle of stroke.

FIG. 7

4. While operating, check for excessive foam buildup

in recovery tank. Use a recommended foam control

solution to prevent vacuum motor damage.

ATTENTION: Excessive foam buildup will not

activate the float shut-off screen. Vacuum motor

damage may result.

5. When floor tool stops spraying, you must drain

recovery tank (See DRAINING TANKS).

6. After cleaning, relieve water pressure from

accessory tool before disconnecting hose.

Squeeze trigger for five seconds after turning off

the main power switch.

EN OPERATION

EX--CAN--10 (04--10)

CLEANING UPHOLSTERY

Optional accessory tool is required.

NOTE: This machine cleans most synthetic upholstery.

Fabrics like Herculon and synthetic will clean with

excellent results. Extraction cleaning is not

recommended for most cottons, silks, wools or natural

fiber velvets. Use extra caution when cleaning

reupholstered furniture, fabric beneath new fabric may

bleed and discolor new fabric.

ATTENTION: When cleaning upholstery, always

check cleaning instructions sewn in furniture by

manufacturer.

1. Vacuum the upholstery before cleaning.

2. Test fabric for colorfastness: Pour a small amount

of recommended cleaning solution on a white cloth.

From an area of the upholstery that is hidden from

view, hold cloth on upholstery for one minute. If

color does not transfer to cloth it should be safe to

clean.

3. Attach the optional accessory hand tool to the

vacuum and solution hoses.

4. Place hand tool on fabric and squeeze trigger while

applying pressure on fabric and slowly pull tool

backwards. Be careful not to over wet upholstery.

Repeat stroke without spray to get fabric as dry as

possible. Overlap cleaning strokes to avoid

streaking (Figure 8).

FIG. 8

WARNING: Do Not Pick Up Flammable

Materials Or Reactive Metals.

5. While operating, check for excessive foam buildup

in recovery tank. Use a recommended foam control

solution to prevent vacuum motor damage.

ATTENTION: Excessive foam buildup will not

activate the float shut-off screen. Vacuum motor

damage may result.

6. When the accessory tool stops spraying, you must

drain recovery tank (See DRAINING TANKS).

7. After cleaning, relieve water pressure from

accessory tool before disconnecting hose.

Squeeze trigger for five seconds after turning off

the main power switch.

DRAINING TANKS

FOR SAFETY: When servicing machine, unplug

cord from wall outlet.

ATTENTION: Use different buckets to fill and drain

machine to prevent solution system clogs.

DRAINING RECOVERY TANK

1. Turn machine off and unplug power cord.

2. Turn drain hose knob counterclockwise and pull out

plug to drain (Figure 9).

FIG. 9

3. After draining, replace drain hose knob securely.

DRAINING LEFTOVER CLEANING SOLUTION

1. Connect the 1.4m (4 1/2 ft) clean--out hose to the

vacuum inlet tube. Clean-out hose is supplied with

machine (Figure 10).

FIG. 10

2. Turn the main power switch to the ON position.

3. Submerge the clean-out hose into the solution tank

and vacuum out the leftover solution.

4. Turn off the machine and drain recovery tank.

OPERATION EN

EX--CAN--10 (04--10)

MACHINE MAINTENANCE

To keep machine in good working condition, simply

follow machines daily and monthly maintenance

procedures.

FOR SAFETY: When servicing machine, unplug

cord from wall outlet.

DAILY MAINTENANCE

(Every 4 Hours of Operation)

1. Drain and rinse out recovery tank thoroughly

(Figure 11).

FIG. 11

2. Remove and clean the float shut--off screen,

located in the recovery tank (Figure 12).

FIG. 12

3. Vacuum out the leftover solution from the solution

tank (Figure 13).

FIG. 13

4. Inspect the accessory tool spray pattern for

plugging. If plugged, remove the spray tips and

screens and soak them in acetic acid solution for

up to six hours. Do not use pointed objects to

unplug tips, damage will occur (Figure 14).

FIG. 14

5. Remove any clogged debris in the accessory tool

(Figure 15).

FIG. 15

EN OPERATION

EX--CAN--10 (04--10)

6. Remove and rinse solution tank screen

(Figure 16).

FIG. 16

7. Inspect power cord and cord grip for damage,

replace if damaged. Coil cord neatly after each

use.

8. Clean machine with a nonabrasive, nonsolvent

cleaner (Figure 17).

FIG. 17

9. Inspect vacuum hose for holes and loose cuffs.

MONTHLY MAINTENANCE

(Every 80 Hours of Operation)

1. Flush pump system with an acetic acid solution to

dissolve normal alkaline chemical buildup.

FOR SAFETY: When using machine, follow mixing

and handling instructions on chemical containers.

a. Premix .5L (16 oz) of an acetic acid solution

with 7.5L (2 gal) of hot water 60_C (140_F)

and pour into solution tank.

b. Connect accessory tool to machine.

c. Turn on the main power switch.

d. With tool over a bucket, squeeze accessory

tool trigger for one minute.

e. Shut off machine and allow remaining solution

to break down alkaline buildup overnight.

f. Next day, spray out remaining solution and

flush system with 11L (3 gal) of clean water.

2. Lubricate wheels and casters with a water resistant

oil.

3. Inspect machine for water leaks.

4. Inspect machine for loose screws.

QUARTERLY MAINTENANCE

(Every 250 of Hours of Operation)

Check vacuum motor for carbon brush wear. Replace

brushes when worn to a length of 10mm (0.38 in) or

less. Contact your Authorized Service Center for

carbon brush inspection.

SERVICING MACHINE

To access internal components for repair, open

machine as described below.

WARNING: Unplug Power Cord Before

Servicing Machine.

FOR SAFETY: When servicing machine, use

manufacturer supplied or approved replacement

parts.

1. Remove two hex--head bolts at front of machine,

using a 9/16” wrench.

ATTENTION: Make sure tanks are empty before

opening.

2. Carefully hinge tank backwards away from chassis

(Figure 18).

FIG. 18

3. When closing machine, keep fingers clear and be

careful not to pinch or kink internal hoses or wiring.

Replace the lift handle and tighten the hex-head

bolts securely.

Inhaltsverzeichnis

Sprachen:

Andere Tennant Bodenreinigungsmaschine Handbücher

Tennant

Tennant T7 Bedienungs- und Montageanleitung

Tennant

Tennant ATLV 4300 Schulungshandbuch

Tennant

Tennant 800 Schulungshandbuch

Tennant

Tennant 613087 Bedienungsanleitung

Tennant

Tennant ATLV 4300 Bedienungsanleitung

Tennant

Tennant T3 Bedienungsanleitung

Tennant

Tennant 385D Bedienungsanleitung

Tennant

Tennant 5700XP Bedienungsanleitung

Tennant

Tennant 443C Bedienungsanleitung

Tennant

Tennant T1 Bedienungsanleitung

Tennant

Tennant M17 Series Schulungshandbuch

Tennant

Tennant T1 Bedienungsanleitung

Tennant

Tennant 5100 Produkthandbuch

Tennant

Tennant 8410D Bedienungsanleitung

Tennant

Tennant R3 ReadySpace Bedienungsanleitung

Tennant

Tennant T5E Bedienungsanleitung

Tennant

Tennant 1220 Produkthandbuch

Tennant

Tennant T17 Series Bedienungsanleitung

Tennant

Tennant ReadySpace 1610 Bedienungsanleitung

Tennant

Tennant T16 Schulungshandbuch

Tennant

Tennant 2330 Bedienungsanleitung

Tennant

Tennant T7 Bedienungsanleitung

Tennant

Tennant 1550 Produkthandbuch

Tennant

Tennant 240 Bedienungsanleitung

Beliebte Bodenreinigungsmaschine Handbücher anderer Marken

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Bedienungsanleitung

Numatic

Numatic ET 4045 Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Bedienungsanleitung

Mytee

Mytee 8070 Mytee-Lite Bedienungsanleitung

Kärcher

Kärcher B 140 R Bedienungsanleitung

Triple S

Triple S Ace 26T1 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SW 750 Bedienungsanleitung

Tornado

Tornado Marathon 2000 98190 Handbuch

Windsor

Windsor ADMIRAL Admiral 8 Bedienungsanleitung

Numatic

Numatic TTB 1117/100 Bedienungsanleitung

Nobles

Nobles Frontier Produkthandbuch

lavina

lavina 21-X Bedienungsanleitung

KENT

KENT Edge 28B Bedienungsanleitung

Windsor

Windsor BDP 51/2000C Bedienungsanleitung

CleanFreak

CleanFreak DURA-18HD Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Administratorhandbuch

BETCO

BETCO PB24 Bedienungsanleitung

IPC

IPC CT51-71 BT Bedienungsanleitung