Tennant M17 Series Schulungshandbuch

IB 9015105 (06- 2017) 1

INSTRUCTION BULLETIN

No. 9015105

Machine: M17

Published: 06- 2017

Rev. 03

NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the

Parts List in the appropriate place in the machine manual for future

reference. Retaining the Parts List will make it easier to reorder

individual parts and will save the cost of ordering an entire kit.

NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.

Installation instructions for kit number 9015041

SYNOPSIS:

This kit contains the parts needed to replace standard pod assembly on M17 sweeper scrubbers.

Please follow step-by-step instructions.

SPECIAL TOOLS / CONSIDERATIONS: NONE

(Estimated time to complete: 50 minutes)

PROTECT THE ENVIRONMENT

Please dispose of packaging materials, used machine components

such as batteries and fluids in an environmentally safe way according

to local waste disposal regulations.

Always remember to recycle.

PREPARATION:

1. If steering pod assembly on machine is

operable, connect service computer to the

pod, turn the key to the ON position, start the

Capture application, and note machine

settings. The new steering pod assembly (1)

must be configured to the same settings.

NOTE:If steering pod assembly is completely

inoperable, the machine configuration settings will

need to be set to the optional equipment on the

machine and / or set to the standard default

settings.

2. If steering pod assembly on machine is

operable, record the hours from the hour

meter.

FOR SAFETY: Before leaving or servicing

machine, stop on level surface, turn off

machine, and remove key.

3. Disconnect the battery cable from the

machine.

WARNING: Always disconnect battery

cables from machine before working on

electrical components.

4. Remove the access panel from the machine.

Set the access panel and all hardware aside.

INSTALLATION:

1. Disconnect the main wire harness from the

steering pod assembly. (Fig. 1)

FIG. 1

IB 9015105 (06- 2017)2

FRONT

Steering

column

assembly

Loosen socket set

screws (Qty. 2)

Steeringwheel

Replace existing

steering pod assembly

with new steering pod

assembly (1)

Bearing plate

Thrust washers

(Qty. 2)

Note: Steering wheel / steering column assembly do not need

to be removed from machine when replacing standard panel

assembly. These items are shown disassembled to better

show part locations.

FIG. 2

2. Loosen the socket set screws in the bearing

plate securing the steering pod assembly to

the steering column assembly. (Fig. 2 / Fig. 3)

FIG. 3

3. Pull the steering pod assembly out from the

steering wheel / steering column assembly.

(Fig. 2)

4. Remove the thrust washers from the removed

steering pod assembly and slide the thrust

washers onto the new steering pod assembly

(1). Discard the removed steering pod

assembly. (Fig. 2)

5. Insert the new steering pod assembly (1) into

the steering assembly. (Fig. 2)

6. Orient the steering pod assembly (1) so the

display is positioned correctly in the steering

wheel and tighten the socket screws to secure

the steering pod assembly into the bearing

plate. (Fig. 2 / Fig. 3)

7. Connect the steering pod assembly (1) to the

main wire harness. (Fig. 1)

8. Reinstall the access panel onto the machine

9. Reconnect the battery cable to the machine.

IB 9015105 (06- 2017) 3

ACCESSING TENNANT SERVICE

APPLICATION SOFTWARE:

Tennant Service Application Software is required

to program the new control console control board.

The software can be accessed or installed.

For Tennant service personnel equipped with

ServiceLink computers, the software is already

installed on the service computer.

Proceed to PROGRAM THE CONTROL BOARD.

For other Service Groups,download the Service

Application Software from the “My Tennant”

website. Frequently check site for latest version of

the Service Application Software.

1. Go to www.tennantco.com and click on the

“My Tennant Customer Sign In” tabinthe

upper left corner. (Fig. 4)

FIG. 4

2. Log on to the “My Tennant” website or register

as a new user. (Fig. 5)

FIG. 5

3. Once logged on to the “My Tennant” website,

click on the “Service Application Software”

link in the “Product Support & Solution”

section. (Fig. 6)

FIG. 6

4. Within the Service Application Software page,

click on the “Service Diagnostics...” link to

download the application installer. (Fig. 7)

NOTE:If the version is the same as current

install, there is no need to update..

FIG. 7

IB 9015105 (06- 2017)4

5. Click the Save button.(Fig. 8)

FIG. 8

6. Open the Downloads folder and click on the

“Setup” file to install the application software

onto the computer. (Fig. 9)

FIG. 9

7. After the application software is installed on

the computer, Proceed to PROGRAM THE

CONTROL BOARD.

PROGRAM THE CONTROL BOARD:

If any problems are encountered during the

programming process, contact the Technical

Service Department for support.

1. Access the software through either the

desktop icon or the Start Menu. The software

application is titled “Service Diagnostics”.

(Fig.10/Fig.11/Fig.12)

FIG. 10

From Start menu

FIG. 11

Start menu > All Programs > Tennant

Company > Tennant Service Diagnostics

FIG. 12

IB 9015105 (06- 2017) 5

2. Start the Service Software Application

program. The following screen will appear.

(Fig. 13)

FIG. 13

3. Connect the USB cable to the computer and

the USB port on machine. Turn the key switch

to the ON position.

4. The application software will connect to the

machine (Fig. 14).

FIG. 14

If the application remains on the “Connecting

to Machine...” screen for an extended period,

cycle key or close and restart the application

software. If it still fails to connect, restart the

computer.

5. The following screen appears when the

application software is connected to machine

(Fig. 15). Enter the machine serial number

from the label on machine (ex. M17-

12345678). Select the appropriate model from

the drop- down menu. Click the arrow button

to advance to next screen.

FIG. 15

6. Carefully select the correct installed options

on the machine (Fig. 16). This may require

visually inspecting the machine to confirm all

installed options. Click the arrow button to

advance to next screen.

NOTE: If the machine is configured with an option

it does not have, a fault code may appear during

machine start up.

FIG. 16

IB 9015105 (06- 2017)6

7. The application will begin configuring the new

control board. Allow the configuration process

to be completed. (Fig. 17)

FIG. 17

8. The Machine Setup Complete screen appears

after configuration is complete. (Fig. 18)

FIG. 18

9. Disconnect the USB cable from the machine

and turn key off. The machine is now ready

for operation.

10. Test machine to ensure all installed options

are functioning and no fault codes appear. If a

fault code appears, proceed to next step.

11. Reconnect the USB cable to the computer

and the machine. The Main Menu will appear

on the computer screen.

12. Check the machine configuration selections

for incorrect installed options. Click the

Configuration button. (Fig. 19)

FIG. 19

13. Correct the installed options. (Fig. 20)

FIG. 20

14. Click the down arrow button located at the top

right of the window to program the machine. A

green check appears next to the down arrow

button when programmed. (Fig. 20)

15. Cycle key to apply the corrected configuration

setting.

16. Disconnect the USB cable from the machine.

IB 9015105 (06- 2017) 7

17. Press and hold the right arrow key and turn

the key switch to the ON position. (Fig. 21)

FIG. 21

18. The steering pod assembly (1) should boot to

the Service Modes menu. Press the right

arrow button / left arrow button to scroll to the

CONFIG MODE menu from the Service

Modes menu. (Fig. 22)

FIG. 22

19. Press the main scrub brush pressure button

to enter the CONFIG MODE. (Fig. 23)

FIG. 23

20. Press either the right arrow button or the left

arrow button to scroll to C16: PROPEL H. M.

Press the main scrub brush pressure button

to enter the C18: Propel H.M. Log in screen.

(Fig. 24)

FIG. 24

21. Log in to C18: Propel H.M. (hour meter reset

password is 0000): Press the minus (- ) button

to enter 0 (zero) at first asterisk. Press the

right arrow button to move to next asterisk

and again press the minus (- ) button to enter

0 (zero). Repeat for the remaining asterisks.

Press the main scrub brush pressure button

when finished. (Fig. 25 / Fig. 26)

FIG. 25

FIG. 26

IB 9015105 (06- 2017)8

22. Reset the hour meter at the C18: Chg Prpl Hr

screen: Use the minus (- ) button and plus (+)

button to set / reset numbers and the right

arrow button to move to the next number. If

necessary, use left arrow to move back to

previous number. (Fig. 27 / Fig. 28)

FIG. 27

FIG. 28

NOTE:If hour meter was inaccessible due to pod

being inoperable call Field Service Support for the

hour meter time from the last time the machine

was serviced.

23. Press the main scrub brush pressure button

when finished entering the time for the hour

meter.

24. Press either the right arrow button or left

arrow button to scroll to Exit Config Mode.

Yes should appear under the top line of text.

Press the main scrub brush pressure button.

(Fig. 29)

FIG. 29

25. The Exit Config Mode menu should open.

<Yes > should appear under the top

line of text. Press the main scrub brush

pressure button again to exit the Configuration

Mode. (Fig. 30)

FIG. 30

26. Turn key switch to OFF position to turn off the

machine / exit the Config Mode.

27. Turn the key to the ON position and ensure

hopper is completely lowered and rolled in.

The hopper must be completely lowered and

rolled in (in the home position) before it can

be reset to the factory roll settings.

IB 9015105 (06- 2017) 9

28. Press and hold the right arrow key and turn

the key switch to the ON position. (Fig. 31).

FIG. 31

29. The steering pod assembly (1) should boot to

the Service Modes menu. Press the right

arrow button / left arrow button to scroll to the

MANUAL MODE menu from the Service

Modes menu. (Fig. 32)

FIG. 32

30. Press the main scrub brush pressure button

to enter the MANUAL MODE. (Fig. 33)

FIG. 33

31. Press the left arrow button to scroll to M35:

Fact SetRoll. Press the main scrub brush

pressure button to reset the hopper roll out to

the factory setting. (Fig. 34)

FIG. 34

32. Verify the value on the left closely matches

the value in the parentheses. (Fig. 34)

NOTE:The hopper factory roll out setting may

fluctuate +/- 0.002 when reset. This is normal.

33. Turn key switch to OFF position to turn off the

machine / exit the Manual Mode.

34. Retest machine to ensure all installed options

are functioning. Operate the machine with the

various scrub / sweep functions to ensure all

the controls / buttons function. Raise, roll out,

lower, and roll in the hopper to ensure all

hopper functions are operational.

IB 9015105 (06- 2017)10

Bill Of Materials For Panel Kit, Pod, Afmkt [M17,Standard LCD] - 9015041

Ref.

Tennant

Part No. Description Qty.

11219319 )Panel Assy [M17, UL, Standard LCD] 1

TENNANT COMPANY

P. O. Box 1452

Minneapolis, MN 55440-1452

Andere Handbücher für M17 Series

Inhaltsverzeichnis

Andere Tennant Bodenreinigungsmaschine Handbücher

Tennant

Tennant IRIS T300 Bedienungsanleitung

Tennant

Tennant 2370 Bedienungsanleitung

Tennant

Tennant 2100 Produkthandbuch

Tennant

Tennant 3530 Produkthandbuch

Tennant

Tennant 97 Bedienungsanleitung

Tennant

Tennant 265 Bedienungsanleitung

Tennant

Tennant 1200 Produkthandbuch

Tennant

Tennant T1 Bedienungsanleitung

Tennant

Tennant T7 Bedienungsanleitung

Tennant

Tennant EX-SC-1530 Bedienungsanleitung

Tennant

Tennant MM267 Bedienungsanleitung

Tennant

Tennant T1 Bedienungsanleitung

Tennant

Tennant B1 Series Produkthandbuch

Tennant

Tennant S30 XP Schulungshandbuch

Tennant

Tennant 5300T Bedienungsanleitung

Tennant

Tennant 607647 Produkthandbuch

Tennant

Tennant 6100 Bedienungsanleitung

Tennant

Tennant 5540 Produkthandbuch

Tennant

Tennant T7 Bedienungsanleitung

Tennant

Tennant IRIS T300 Bedienungsanleitung

Tennant

Tennant 6600 Bedienungsanleitung

Tennant

Tennant 5280 Bedienungsanleitung

Tennant

Tennant 1140 607681 Produkthandbuch

Tennant

Tennant CS5 Bedienungsanleitung

Beliebte Bodenreinigungsmaschine Handbücher anderer Marken

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Bedienungsanleitung

Numatic

Numatic ET 4045 Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Bedienungsanleitung

Mytee

Mytee 8070 Mytee-Lite Bedienungsanleitung

Kärcher

Kärcher B 140 R Bedienungsanleitung

Triple S

Triple S Ace 26T1 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SW 750 Bedienungsanleitung

Tornado

Tornado Marathon 2000 98190 Handbuch

Windsor

Windsor ADMIRAL Admiral 8 Bedienungsanleitung

Numatic

Numatic TTB 1117/100 Bedienungsanleitung

Nobles

Nobles Frontier Produkthandbuch

lavina

lavina 21-X Bedienungsanleitung

KENT

KENT Edge 28B Bedienungsanleitung

Windsor

Windsor BDP 51/2000C Bedienungsanleitung

CleanFreak

CleanFreak DURA-18HD Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Administratorhandbuch

BETCO

BETCO PB24 Bedienungsanleitung

IPC

IPC CT51-71 BT Bedienungsanleitung