Tennsco 1472 Bedienungsanleitung

GENERAL SAFETY INFORMATION

Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.

For safety, wear a pair of work gloves when assembling or performing any maintenance on products.

LIMITED WARRANTY

Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply

in the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by persons not authorized by Seller, where goods are damaged during

shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:

a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:

b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND SHALL IN NO

EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.

NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the

goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty

and are returned within the warranty period stated above.

ASSEMBLY INSTRUCTIONS & PARTS MANUAL

PK-1760918

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE

Combination Storage Cabinet

Unassembled Model 1472 or CVD1472

Tennsco LLC., Dickson, TN 37056-1888 • (866) 446-8686

LOAD CAPACITIES PER SHELF LEVEL

36w x 18d

18w x 18d

200 lbs.

75 lbs.

UNIT SIZE WEIGHT CAPACITY

EVENLY DISTRIBUTED

ASSEMBLY OF 1472 or CVD1472 CABINET

Tools Needed: A free 11/32” nut driver is included with each Tennsco cabinet.

Two people are recommended for assembly. Approximate assembly time: 30-40 minutes.

2. Place the cabinet back (Ref. No. 1) on a

protected surface to prevent

scratching the paint.

The ange on the

bottom of the back

should be facing upward.

1. The reference numbers used throughout this sheet refer

to the illustration on the back cover. This is to help you

to identify the various parts as they are mentioned.

3. Attach the left side (Ref. No. 2) to the back by placing

ange (A) around the back and bolting together with

seven bolts and nuts (Ref. Nos. 21 & 22). Be sure that the

lances on all shelf adjustment strips (B) are pointing in the

same direction.

5. Insert the shelf (Ref. No. 4) into

the second lance of the side

and back panels.

6. Attach the top (Ref. No. 5) to the unit by sliding the outer ange

over the back of the unit and the side ange of the side panel on

the unit. The threaded studs should go through

the holes in the top lange of the side and

fasten with three nuts. Attach the back

to the top using four bolts

and nuts.

4. Attach the right side (Ref. No. 3) to the back in the same

manner as you did in step 3, again, making sure that

the ange is around the back and that the lances on the

shelf adjustment strips are pointed in the same direction

as those on the back and left side. 8. Place the rear ange of the bottom (Ref. No. 7) into the

bottom lances of the back. The ange with two holes should

face the front, hanging over the sill. Insert the bolts through

the bottom and still with the head

facing the front of the unit.

Secure with two nuts.

Tighten all bolts.

⁭

All lances point UP on

both backs and side.

Flange goes

under back.

Flange faces upward.

Flanges

face upward

Slide ends in to the slots

on the bottom of the sides.

Nuts placed loosely

on studs of the sill.

Insert bottom into

bottom lances.

⁭

NOTE: When bolting the unit together, leave

the bolts slightly loose until Step 8, unless

otherwise speciﬁed.

NOTE: All illustrations show a solid door. Assembly

for C-Thru doors (CVD1472) is identical.

Two holes must

be in front

⁭

Inset A

Use 2nd

lance

7. Next, attach the sill (Ref. No. 6) to the sides, as shown above.

Place nuts loosely on each of the studs and slide the ends of the

sill into the slots on both sides of the unit. Then, securely tighten

the nuts.

⁭

11. Insert the four partition shelves

(Ref. No. 11) at the desired levels.

The shelves should be inserted

using the same method used to

place the top shelf.

10. Attach the left coat rod bracket

(Ref. No. 19) beneath the left side

of the cabinet shelf by inserting one

bolt through the hole in the

left edge of the shelf. Secure with a

nut. Attach the right bracket in

the same way. Then slide the

coat rod (Ref. No. 18) through the

holes in the brackets.

Leveler

Access Holes

9. Using two people, set the unit

upright and insert the partition

(Ref. No. 10) into the cabinet,

alining the four holes in the

partition with the holes in the

cabinet bottom and the

cabinet shelf. Attach

with four bolts and

nuts, making sure that

the bolts are inserted from

the top downward to prevent

stored items from being snagged.

NOTE: In order to place the

shelves, you must ﬁrst tilt

the shelf slightly to the left

or right before inserting

into the unit.

13. The cabinet must be level

in order for the doors to

close properly. Levelers

may be adjusted by

placing the nut driver

through the hole in each

end of the sill and adjusting

the leveling screw.

12. Attach the left door (Ref.

No. 8) and the right door

(Ref. No. 9) to the unit

by placing the door on

the hinges, aligning the

hinge holes, and dropping

the hinge pins (Ref. No.

17) into the slots. Then,

tap the top of each hinge

pin until fully seated.

1. Place the locking handle

(Ref. No. 13) on the right

hand door and fasten with

two #8-32 X 1/4hex-head

bolts and lock washers,

provided with the handle.

2. Turn the handle to the

open position and

place the locking cam

(Ref. No. 14) over the

square shank of the

door handle. The latch

must be facing downward

as shown. Then place the

locking cotter pin (Ref. No.

15) through the hole of the

square shank.

3. With the handle still in the open position, hook the

locking bars (Ref. No. 12) to the locking cam (see

“A” at left). Once in position, slowly rotate the door

handle to the closed position so the lock bars

prot rude from the holes at the top and bottom

of the door (shown at right, below).

4. Slide the nylon lock bar

guide inserts (Ref. No.

16) over the lock bar

ends and through the

door slots (see “B” at

right). Push down rmly

until the guides snap

into place.

Handle/Locking System Installation

⁭

⁭⁭

⁭

⁭⁭

⁭

REPLACEMENT PARTS

⁭

Tennsco Nut Driver

(Ref No. 20)

Bottom

(Ref No. 7)

Sill

(Ref No. 6)

Left Side

(Ref No. 2)

Top

(Ref No. 5)

Shelf

(Ref No. 4)

Right Side

(Ref No. 3)

Cotter Pin

(Ref No. 15)

Locking Bar Guide

Nylon Insert

(Ref No. 16)

Locking Bar Set

(Ref No. 12)

Locking Cam

(Ref No. 14)

Locking Handle

with Keys

(Ref No. 13)

Back Panel

(Ref No. 1)

REF. NO. DESCRIPTION

1 Back Panel 1 944BA

2 Left Side 1 944LS

3 Right Side 1 944RS

4 Shelf 1 301

5 Top 1 944TO

6 Sill 1 944SIN

7 Bottom 1 292BO

8 Left Door: Solid for 1472 1 944LD

Left Door: C-Thru for CVD1472 (not shown above) 1 CVD-72LD

9 Right Door: Solid for 1472 1 944RD

Right Door: C-Thru for CVD1472 (not shown above) 1 CVD-72RD

10 Partition 1 047PA

11 Partition Shelves 4 304

12 Locking Bar Set 1 944LB

13 Locking Handle w/keys & hardware 1 944LH

14 Locking Cam* 1 944LC

15 Cotter Pin* 1 CTRPN

16 Locking Bar Guide Insert (Nylon)* 2 944GI

17 Hinge Pins* (not shown above) 6 944HP

18 Coat Rod 1 046CR

19 Coat Rod Bracket 2 045RB

20 Tennsco Nut Driver 1 TOOL-2

21 #8-32 x 3/8” bolts (not shown above) 26 **

22 #8-32 nuts (not shown above) 36 **

*Included in Ref. No. 13, locking handle with keys and hardware (Part No. 944LH). **Available Locally

QTY. PART NO.

⁭

Left Door

(Ref No. 8)

Right Door

(Ref No. 9)

Coat Rod

(Ref No. 18)

Partition Shelf

(Ref No. 11)

⁭

Coat Rod

Bracket

(Ref No. 19)

⁭

Partition

(Ref No. 10)

⁭

NOTE: Additional hardware may be included for replacement purposes.

Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.

However, should your unit contain missing or damaged parts, please contact your purchase location.

49B176

Dieses Handbuch passt für folgende Modelle

Andere Tennsco Inneneinrichtung Handbücher

Tennsco

Tennsco SRS-601878 Series Bedienungsanleitung

Tennsco

Tennsco 1870RH Bedienungsanleitung

Tennsco

Tennsco Imperial Shelving Bedienungsanleitung

Tennsco

Tennsco Open Foreman's Desk Bedienungsanleitung

Tennsco

Tennsco Jumbo Storage Cabinet J2478SU Bedienungsanleitung

Tennsco

Tennsco 1870 Bedienungsanleitung

Tennsco

Tennsco WELDED 3-PERSON LOCKER Bedienungsanleitung

Tennsco

Tennsco J2478A-N Bedienungsanleitung

Tennsco

Tennsco J2478A-N-W Bedienungsanleitung

Tennsco

Tennsco WBHC-1516-MGY Bedienungsanleitung

Tennsco

Tennsco B-3000 Bedienungsanleitung

Tennsco

Tennsco ESP-1236 Bedienungsanleitung

Tennsco

Tennsco 1472 Bedienungsanleitung

Tennsco

Tennsco BCD18-72 Bedienungsanleitung

Tennsco

Tennsco J1878A-N-W Bedienungsanleitung

Tennsco

Tennsco Standard Combination Cabinet CVD7214 Bedienungsanleitung

Tennsco

Tennsco EB-12 Bedienungsanleitung

Tennsco

Tennsco BK6-121512-3 Bedienungsanleitung

Tennsco

Tennsco ZA7-4824S-4D Bedienungsanleitung

Tennsco

Tennsco Z-Line Steel Shelf Unit Bedienungsanleitung

Tennsco

Tennsco APT-3672S Bedienungsanleitung

Tennsco

Tennsco CINCO NIVELES Bedienungsanleitung

Tennsco

Tennsco Stackable Workbench Drawer Unit Bedienungsanleitung

Tennsco

Tennsco 1871 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung