Tennsco J2478A-N-W Bedienungsanleitung

PK-2800918

ASSEMBLY INSTRUCTIONS & PARTS MANUAL

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE

Jumbo Wardrobe Cabinet

Unassembled Model J2478A-N-W

Tennsco LLC.

, Dickson, TN 37056-1888 • (866) 446-8686

GENERAL SAFETY INFORMATION

Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.

For safety, wear a pair of work gloves when assembling or performing any maintenance on the units.

LIMITED WARRANTY

Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply in

the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by persons not authorized by Seller, where goods are damaged during

shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:

a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:

b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND SHALL IN NO

EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.

NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the

goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty

and are returned within the warranty period stated above.

LOAD CAPACITIES PER SHELF LEVEL

48w x 24d 400 lbs.

UNIT SIZE WEIGHT CAPACITY

EVENLY DISTRIBUTED

ASSEMBLY OF J2478A-N-W CABINET

Tools Needed: A free 11/32” nut driver is included with each Tennsco cabinet.

Two people are recommended for assembly. Approximate assembly time: 30-40 minutes.

2. Place the 2-piece cabinet back (Ref.

No. 1) on a protected surface to

prevent scratching the paint.

The ange on the

bottom of the back

should be facing upward.

Bolt the back panels together with

seven bolts and nuts (Ref Nos. 19 & 20).

1. The reference numbers used throughout this sheet refer

to the illustration on the back cover. This is to help you

to identify the various parts as they are mentioned.

3. Attach the left side (Ref. No. 2) to the back by placing

ange (A) around the back and bolting together with

seven bolts and nuts. Be sure that the lances on all

shelf adjustment strips (B) point in the same direction.

5. Attach the right side (Ref. No. 3) to the back in the same manner

as you did in step 3, again, making sure that the ange is

around the back and that the lances on the shelf adjustment

strips are pointed in the same direction as those on the back and

left side. Push the side panel up so the studs in the top go

through the holes in the top

ange of the side and

fasten with three

nuts as in

step 4).

6. Attach the sill (Ref. No. 8) to the sides. Place nuts loosely on each

of the studs and slide the ends of the sill into the slots on both

sides of the unit. Then, securely tighten the nuts.

4. Attach the top (Ref. No. 5) to the unit by sliding the outer

ange over the back of the unit and the side ange on

the top over the side panel. The

threaded studs should go

through the holes in the

top ange of the

side and

fasten with

three nuts.

Attach the

back to the

top using four

bolts and nuts.

7. Place the rear ange of one of the shelves (Ref. No. 4) into the

four bottom lances of the back. The front of the shelf will rest

on the sill.

⁭

All lances point UP on

both backs and side.

Flange goes

under back.

Flange faces upward.

Flanges

face upward

Threaded studs go

through the holes

in the ﬂange at the

top of the side.

Slide ends in to the slots

on the bottom of the sides.

Nuts placed loosely

on studs of the sill.

Insert bottom into

bottom lances.

⁭

NOTE: When bolting the unit together, leave

the bolts slightly loose until Step 10, unless

otherwise speciﬁed.

8. Insert the second shelf into the

second lance from the top of

the sides and back.

⁭

1. Place the locking handle

(Ref. No. 12) on the right

hand door and fasten with

two #8-32 X 1/4hex-head

bolts and lock washers,

provided with the handle.

2. Turn the handle to the

open position and

place the locking cam

(Ref. No. 13) over the

square shank of the

door handle. The latch

must be facing downward

as shown. Then place the

locking cotter pin (Ref. No.

15) through the hole of the

square shank.

3. With the handle still in the open position, hook the

locking bars (Ref. No. 11) to the locking cam (see

“A” at left). Once in position, slowly rotate the door

handle to the closed position so the lock bars

prot rude from the holes at the top and bottom

of the door (shown at right, below).

4. Slide the nylon lock bar

guide inserts (Ref. No.

14) over the lock bar

ends and through the

door slots (see “B” at

right). Push down rmly

until the guides snap

into place.

5. Attach the “dummy” handle

(Ref. No. 16) using two

#8-32 X 1/4hex-head bolts

and lock washers.

Handle/Locking System Installation

⁭

11.

The cabinet must be level in order for the doors to close

properly. Levelers may be adjusted by placing the nut driver

through the hole in each end of the sill and adjusting the

leveling screw.

⁭

Attach the left coat rod bracket (Ref. No. 9) to the underside of

the shelf, inserting one bolt and nut through the hole provided

9. Using two people, set the

unit upright. Attach the left

door (Ref. No. 6) and right

door (Ref. No. 7) to the unit

by placing the door on the

hinges, aligning the hinges

on the door to the hinges on

the sides, pushing the hinge

pins (Ref. No. 17) through

both hinges. Tap the top of

each hinge pin until it is

fully seated.

10.

on the far right and far

left side. The open side of

the side brackets should

face into the unit. Place

the last bracket on the

coat rod (Ref. No. 10)

and insert the rod into

the other by exing the

second bracket. Secure

the bracket to the middle

of the shelf with one bolt

and nut through the hole

provided in the center

of the shelf. At this time,

tighten all of the nuts

and bolts around the

entire unit.

Leveler

Access Holes

⁭

REPLACEMENT PARTS

⁭

⁭⁭

⁭

Tennsco Nut Driver

(Ref No. 18)

Hinge Pin

(Ref No. 17)

Coat Rod

(Ref No. 10)

Sill

(Ref No. 8)

Coat Rod

Bracket

(Ref No. 9)

Dummy Handle

(Ref No. 16)

Left Side

(Ref No. 2)

Top

(Ref No. 5)

Shelf

(Ref No. 4)

Right Side

(Ref No. 3)

Cotter Pin

(Ref No. 15)

Locking Bar Guide

Nylon Insert

(Ref No. 14)

Locking Bar Set

(Ref No. 11)

Locking Cam

(Ref No. 13)

Locking Handle

with Keys

(Ref No. 12)

Back Panel

(Ref No. 1)

REF. NO. DESCRIPTION

1 Back Panels 2 055BA

2 Left Side 1 056LS

3 Right Side 1 056RS

4 Shelf 2 307

5 Top 1 055T24

6 Left Door 1 056LD

7 Right Door 1 056RD

8 Sill 1 055SI

9 Coat Rod Bracket 3 045RB

10 Coat Rod 1 055CR

11 Locking Bar Set 1 043LB

12 Locking Handle w/keys & hardware 1 043LH

13 Locking Cam* 1 944LC

14 Locking Bar Guide Insert (Nylon)* 2 944GI

15 Cotter Pin* 1 CTRPN

16 Dummy Handle* 1 043DH

17 Hinge Pins* 8 944HP

18 Tennsco Nut Driver 1 TOOL-2

19 #8-32 x 3/8” bolts (not shown above) 25 **

20 #8-32 nuts (not shown above) 35 **

*Included in Ref. No. 12, locking handle with keys and hardware (Part No. 043LH). **Available Locally

QTY. PART NO.

⁭

Left Door

(Ref No. 6)

Right Door

(Ref No. 7)

NOTE: Additional hardware may be included for replacement purposes.

Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.

However, should your unit contain missing or damaged parts, please contact your purchase location.

Andere Tennsco Inneneinrichtung Handbücher

Tennsco

Tennsco Z-Line Steel Shelf Unit Bedienungsanleitung

Tennsco

Tennsco B-8400 Bedienungsanleitung

Tennsco

Tennsco 3018 Bedienungsanleitung

Tennsco

Tennsco 1870 Bedienungsanleitung

Tennsco

Tennsco Imperial Shelving Bedienungsanleitung

Tennsco

Tennsco 3070 Bedienungsanleitung

Tennsco

Tennsco 1436 Bedienungsanleitung

Tennsco

Tennsco J1878C-N Bedienungsanleitung

Tennsco

Tennsco APT-3672S Bedienungsanleitung

Tennsco

Tennsco JUMBO Gebrauchsanweisung

Tennsco

Tennsco CC-30 Bedienungsanleitung

Tennsco

Tennsco B-3000 Bedienungsanleitung

Tennsco

Tennsco 1871 Bedienungsanleitung

Tennsco

Tennsco RGL-1236S Bedienungsanleitung

Tennsco

Tennsco DWR-4218 Bedienungsanleitung

Tennsco

Tennsco Jumbo Storage Cabinet J1878SU Bedienungsanleitung

Tennsco

Tennsco ZL7 Series Bedienungsanleitung

Tennsco

Tennsco ESPC-1236 Bedienungsanleitung

Tennsco

Tennsco Enclosed Foreman’s Desk Bedienungsanleitung

Tennsco

Tennsco Standard Combination Cabinet 7220 Bedienungsanleitung

Tennsco

Tennsco Imperial Shelving 3630 Bedienungsanleitung

Tennsco

Tennsco SINGLE TIER Bedienungsanleitung

Tennsco

Tennsco ZA7-4824S-4D Bedienungsanleitung

Tennsco

Tennsco WBHC-1516-MGY Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung