Terex Z4525XCF-101 Bedienungsanleitung

Operator's Manual

Serial Number Range

Z®-45 XC™

from Z4525XCF-101

AUS

Australia

with

Maintenance

Information

Original Instructions

First Edition

Second Printing

Part No. 1301594GT

Operator's Manual First Edition • Second Printing

Z®-45 XC™Part No. 1301594GT

Front Matter

Contents

Introduction ........................................................... 1

Symbol and Hazard Pictorials Definitions............. 5

General Safety ...................................................... 8

Personal Safety................................................... 11

Work Area Safety................................................ 12

Legend ................................................................ 22

Controls............................................................... 23

Inspections.......................................................... 36

Operating Instructions......................................... 49

Transport and Lifting Instructions ....................... 59

Maintenance ....................................................... 62

Specifications...................................................... 66

First Edition: Second Printing, June 2022

Genie and "Z" are registered trademarks of Terex South

Dakota, Inc. in the U.S.A. and many other countries.

These machines comply with

AS 1418.10

First Edition • Second Printing Operator's Manual

Introduction

Part No. 1301594GT Z®-45 XC™1

Introducti on

About this manual

Genie appreciates your choice of our machine for

your application. Our number one priority is user

safety, which is best achieved by our joint efforts.

This book is an operation and daily maintenance

manual for the user or operator of a Genie

machine.

This manual should be considered a permanent

part of your machine and should remain with the

machine at all times. If you have any questions,

contact Genie.

Product Identification

The machine serial number is located on the serial

label.

Serial number

stamped on chassis

Serial label

(located under cover)

Intended Use and Familiarization

Guide

The intended use of this machine is to lift

personnel, including tools, and materials to an

aerial work site. Before operating the machine, it’s

the operator’s responsibility to read and

understand this familiarization guide.

Each person must be trained to operate a

Mobile Elevating Work Platform (MEWP).

Familiarization with the MEWP must be given

to each person who is authorized, competent

and trained.

Only trained and authorized personnel should

be permitted to operate the machine.

The operator is responsible to read,

understand, and obey the manufacturer’s

instructions and safety rules provided in the

Operator’s Manual.

The Operator’s Manual is located in the

manual storage container, at the platform.

For specific product applications, see

Contacting The Manufacturer.

Operator's Manual First Edition • Second Printing

Introduction

2 Z®-45 XC™Part No. 1301594GT

Platform controls symbology and related

machine movement:

Platform level swtich

Platform rotate switch

Jib boom up/down

Primary boom up/down

Turntable rotate

Primary boom

extend/retract

switch

Secondary boom up/down

Drive forward/reverse

Steer right/left

Ground controls symbology and related

machine movement:

Platform level, jib boom

up/down, primary boom

extend/retract, primary

boom up/down, and

secondary boom

retract/lower.

Turntable rotate and

platform rotate

Sequential functions and movement:

•Drive and steer.

Interlocked functions:

•Elevated drive speed.

•Elevated drive in an off-level condition.

•Drive enable when the boom is rotated past

the non-steer wheels.

•All platform and ground controls.

Limitations of use:

•The intended use of this machine is to lift

personnel, including tools, and materials to an

aerial work site.

•Do not elevate the platform unless the machine

is on firm level ground.

Stability enhancing means:

•Foam filled tires (if equipped).

Restricted operating envelope:

•1,000 lbs/454 kg platform capacity. (if

equipped)

First Edition • Second Printing Operator's Manual

Introduction

Part No. 1301594GT Z®-45 XC™3

Bulletin Distribution and

Compliance

Safety of product users is of paramount

importance to Genie. Various bulletins are used by

Genie to communicate important safety and

product information to dealers and machine

owners.

The information contained in the bulletins is tied to

specific machines using the machine model and

serial number.

Distribution of bulletins is based on the most

current owner on record along with their

associated dealer, so it is important to register

your machine and keep your contact information

up to date.

To ensure safety of personnel and the reliable

continued operation of your machine, be sure to

comply with the action indicated in a respective

bulletin.

Contacting the Manufacturer

At times it may be necessary to contact Genie.

When you do, be ready to supply the model

number and serial number of your machine, along

with your name and contact information. At

minimum, Genie should be contacted for:

Accident reporting

Questions regarding product applications and

safety

Standards and regulatory compliance information

Current owner updates, such as changes in

machine ownership or changes in your contact

information. See Transfer of Ownership, below.

Transfer of Machine Ownership

Taking a few minutes to update owner information

will ensure that you receive important safety,

maintenance and operating information that

applies to your machine.

Please register your machine by visiting us on the

web at www.genielift.com or by calling us toll free

at 1-800-536-1800.

Operator's Manual First Edition • Second Printing

Introduction

4 Z®-45 XC™Part No. 1301594GT

Danger

Failure to obey the instructions and

safety rules in this manual will result

in death or serious injury.

Do Not Operate Unless:

You learn and practice the principles of safe

machine operation contained in this operator’s

manual.

1 Avoid hazardous situations.

Know and understand the safety rules

before going on to the next section.

2 Always perform a pre-operation inspection.

3 Always perform function tests prior to use.

4 Inspect the workplace.

5 Only use the machine as it was intended.

You read, understand and obey the

manufacturer’s instructions and safety rules—

safety and operator’s manuals and machine

decals.

You read, understand and obey employer’s

safety rules and worksite regulations.

You read, understand and obey all applicable

governmental regulations.

You are properly trained to safely operate the

machine.

Safety Sign Maintenance

Replace any missing or damaged safety signs.

Keep operator safety in mind at all times. Use mild

soap and water to clean safety signs. Do not use

solvent-based cleaners because they may

damage the safety sign material.

Hazard Classification

Decals on this machine use symbols, color coding,

and signal words to identify the following:

Safety alert symbol

—

used to alert

you to potential personal injury

hazards. Obey all safety

messages that follow this symbol

to avoid possible injury or death.

Indicates a hazardous situation

which, if not avoided, will result in

death or serious injury.

Indicates a hazardous situation

which, if not avoided, could result

in death or serious injury.

Indicates a hazardous situation

which, if not

avoided, could result

in minor or moderate injury.

Indicates a property damage

message.

First Edition • Second Printing Operator's Manual

Symbol and Hazard Pictorials Definitions

Part No. 1301594GT Z®-45 XC™5

Symbol and Hazard Pic torials Definiti ons

Crush hazard Keep away from

moving parts

Read the operator’s

manual

Fire extinguisher Overhead obstruction

Electrocution hazard Maintain required

clearance

Tip-over hazard Manual force Tip-over hazard

Electrocution hazard Avoid contact Disconnect battery Lifting point Wind speed

Operator's Manual First Edition • Second Printing

Symbol and Hazard Pictorials Definitions

6 Z®-45 XC™Part No. 1301594GT

Weight of welder

reduces capacity

No smoking.

No flame.

Stop engine.

Explosion hazard Collision hazard Corrosive acid.

Wheel load Tire specifications No smoking Overhead

obstruction

Explosion hazard

Platform tie-down

instructions

Lifting and tie down

instructions

Lanyard anchorage

points

Support the platform

or boom during

maintenance

Tie-down point

First Edition • Second Printing Operator's Manual

Symbol and Hazard Pictorials Definitions

Part No. 1301594GT Z®-45 XC™7

Maximum capacity Runaway hazard Color coded

direction arrows

Voltage rating for

power to platform

Pressure rating for air

line to platform

Recovery procedure if tilt alarm sounds while

elevated.

Platform uphill:

Lower primary.

Lower secondary.

3 Retract primary.

Platform downhill:

Retract primary.

Lower secondary.

3 Lower primary.

Access by trained

and authorized

personnel onlyl

Emergency lowering Read the service

manual

Do not use ether or

other high energy

starting aids on

machines equipped

with glow plugs.

Crush hazard

Operator's Manual First Edition • Second Printing

General Safety

8 Z®-45 XC™Part No. 1301594GT

General Safety

* These decals are model, option or configuration specific.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Terex Hubarbeitsbühne Handbücher

Terex

Terex Genie Z-45/25 Bi-Energy Bedienungsanleitung

Terex

Terex Genie S-60 FE Bedienungsanleitung

Terex

Terex Z60H-3000 Bedienungsanleitung

Terex

Terex S85XCH-3740 Bedienungsanleitung

Terex

Terex Genie Z-45 FE Installations- und Betriebsanleitung

Terex

Terex Z30NF-23000 Bedienungsanleitung

Terex

Terex Genie ZX-135/70 Installations- und Betriebsanleitung

Terex

Terex TM Series Bedienungsanleitung

Terex

Terex Genie GTH-4518 ER Bedienungsanleitung

Terex

Terex Genie S-3200 Bedienungsanleitung

Terex

Terex Genie Z-34 IC Installations- und Betriebsanleitung

Terex

Terex Genie GTH1056 Installations- und Betriebsanleitung

Terex

Terex Genie GS-3369DC Bedienungsanleitung

Terex

Terex Z80H-7733 Bedienungsanleitung

Terex

Terex Genie ZX-135/70 Bedienungsanleitung

Terex

Terex Genie GS-2669DC Bedienungsanleitung

Terex

Terex Genie Z6215A-101 Bedienungsanleitung

Terex

Terex Genie Z331815M-101 Bedienungsanleitung

Terex

Terex Genie ZX-135/70 Bedienungsanleitung

Terex

Terex Genie S-45XC Bedienungsanleitung

Terex

Terex Genie TZ-50 Bedienungsanleitung

Terex

Terex Genie GR-20J Bedienungsanleitung

Terex

Terex GTH10T-16501 Installations- und Betriebsanleitung

Terex

Terex Genie Z-34 Bedienungsanleitung

Beliebte Hubarbeitsbühne Handbücher anderer Marken

Genie

Genie Z-80 Bedienungsanleitung

Genie

Genie Z-45/25 Bedienungsanleitung

JLG

JLG Skytrak 6036 Gebrauchs- und Pflegehandbuch

LGMG

LGMG T65JE Bedienungsanleitung

Genie

Genie Z-135/70 Bedienungsanleitung

Oshkosh Corporation

Oshkosh Corporation JLG H800AJ Gebrauchs- und Pflegehandbuch

Oshkosh

Oshkosh JLG 1500SJ Installations- und Benutzerhandbuch

Skyjack

Skyjack SJ30AJE Bedienungsanleitung

Oshkosh

Oshkosh JLG 800A Installations- und Benutzerhandbuch

Skyjack

Skyjack SJ 46AJ Bedienungsanleitung

Molift

Molift Quick Raiser 205 Bedienungsanleitung

Snorkel

Snorkel SL26RTE Kurzanleitung

Oshkosh Corporation

Oshkosh Corporation JLG E300A Bedienungsanleitung

Skyjack

Skyjack SJ45 T+ Bedienungsanleitung

Genie

Genie S-105 Bedienungsanleitung

nifty

nifty 170SD series Montageanleitung

JLG

JLG 15MVL Series Bedienungsanleitung

Genie

Genie Z-45 XC Bedienungsanleitung