TESTO 616 Bedienungsanleitung
testo 616
Materialfeuchte-Messgerät Bedienungsanleitung
Material moisture measuring instrument Instruction manual
Appareil de mesure de l'humidité
des matériaux. Mode d’emploi
Content 17
Content
General notes ....................................................18
1. Safety instructions..............................................19
2. Intended purpose ..............................................20
3. Product description ............................................21
3.1 Display and control elements ........................................21
3.2 Voltage supply ..............................................................22
3.3 Humidity measurement procedure ................................22
4. Commissioning ..................................................23
5. Operation ..........................................................23
5.1 Switching the instrument on/off ....................................23
5.2 Switching the display light on/off ..................................24
5.3 Performing settings ......................................................24
6. Measuring ..........................................................25
7. Care and maintenance ......................................27
8. Questions and answers......................................28
9. Technical data ....................................................28
10. Tips and assistance............................................29
11. Accessories/spare parts ....................................29
deenfresitptsvnl????
General notes18
General notes
This chapter provides important advice on using this
documentation.
This documentation contains information that must be
applied if the product is to be used safely and efficiently.
Please read this documentation through carefully and
familiarize yourself with the operation of the product before
putting it to use. Keep this document to hand so that you
can refer to it when necessary.
Identification
Representation Meaning Comments
Warning advice: Warning! Read warning advice carefully and take
the precautionary measures indicated!
Serious physical injury could occur if
you do not take the precautionary
measures indicated.
Warning advice: Caution! Read warning advice carefully and take
the precautionary measures indicated!
Slight physical injury or damage to
equipment could occur if you do not
take the precautionary measures
indicated.
Note Offers helpful tips and information.
±, 1, 2 Objective Denotes the objective that is to be
achieved via the steps described. Where
steps are numbered, you must always
follow the order given!
Condition A condition that must be met if an action
is to be carried out as described.
i, 1, 2, ... Step Carry out steps. Where steps are
numbered, you must always follow the
order given!
Text Display text Text appears on the instrument display.
Control key Press the key.
- Result Denotes the result of a previous step.
ºCross-reference Refers to more extensive or detailed
information.
Taste
1. Safety instructions 19
1. Safety instructions
This chapter gives general rules which must be followed
and observed if the product is to be handled safely.
Avoiding personal injury/damage to equipment
iDo not use the measuring instrument and sensors to
measure on or near live parts.
iNever store the measuring instrument/probe together
with solvents and do not use any desiccants.
Product safety/preserving warranty claims
iOperate the measuring instrument only within the
parameters specified in the Technical data.
iAlways use the measuring instrument properly and for its
intended purpose. Do not use force.
iDo not expose handles and feed lines to temperatures in
excess of 70 °C unless they are expressly permitted for
higher temperatures. Temperatures given on
probes/sensors relate only to the measuring range of the
sensors.
iOpen the instrument only when this is expressly
described in the documentation for maintenance and
repair purposes.
Carry out only the maintenance and repair work that is
described in the documentation. Follow the prescribed
steps when doing so. For safety reasons, use only
original spare parts from testo.
Ensure correct disposal
iTake faulty rechargeable batteries/spent batteries to the
collection points provided for them.
iSend the product back to testo at the end of its useful
life. We will ensure that it is disposed of in an
environmentally friendly manner.
deenfresitptsvnl????
2. Intended purpose20
2. Intended purpose
This chapter gives the areas of application for which the
product is intended.
Use the product only for those applications for which it was
designed. Ask testo if you are in any doubt.
The product was designed for the following
tasks/applications:
· Fast and non-destructive evaluation of material moisture
courses in woods and building materials.
Does not replace reference methods such as CM
method or Darr-Wäge (dry-and-weigh) method.
The instrument is not calibratable.
The product must not be used in the following areas:
· Areas at risk of explosion.
Materials subject to electrical voltage.
Electric shock!
If in doubt, check whether the materials are
energized before the measurement (e.g. in the
event of water damage in walls)
3. Product description 21
3. Product description
This chapter provides an overview of the components of
the product and their functions.
3.1 Display and control
elements
Overview Contact plates
Display
Control keys
Battery compartment (rear)
Key functions
Key Functions
Switch instrument on;
switch instrument off (press and hold)
Switch display light on/off
Keep reading, display
maximum/minimum value
Open/leave configuration mode (press
and hold);
In configuration mode:
Confirm input
In configuration mode:
Increase value, select option
In configuration mode:
Decrease value, select option
Important displays
Display Meaning
Battery capacity (bottom right in display):
· 4 segments in the battery symbol are lit: Instrument battery is fully
charged
· No segments in the battery symbol are lit: Battery is almost spent
deenfresitptsvnl????
3. Product description22
3.2 Voltage supply
Voltage is supplied by means of a 9 V monobloc battery
(included in delivery) or rechargeable battery. It is not
possible to run the instrument from the mains supply or
charge a rechargeable battery in the instrument.
3.3 Humidity measurement
procedure
The non-destructive stray field measurement uses the
ability of water molecules to dampen and thus change
electromagnetic fields. The electric field penetrates the
material via the contact plates and creates a measuring
field with a depth of approx. 5 cm (2”).
The following factors can influence the measurement result:
Factors Ideal condition
Measurement depth Material thickness > 5 cm (> 2”). Caution: The upper
layers of the material influence the measurement result
more than the deeper layers.
Material surface As level as possible as contact plates should lay flat
against it.
Material properties As homogeneous as possible with no air pockets.
Moisture distribution As even as possible.
Metals and electric fields None, if possible.
4. Commissioning 23
4. Commissioning
This chapter describes the steps required to commission
the product.
²Removing the protective film on the display:
iPull the protective film off carefully.
²Inserting a battery/rechargeable battery:
1To open the battery compartment on the rear of the
instrument, push the lid of the battery compartment in
the direction of the arrow and remove it.
2Insert a battery/rechargeable battery (9 V monobloc).
Observe the polarity!
3To close the battery compartment, replace the lid of
the battery compartment in position and push it
against the direction of the arrow.
5. Operation
This chapter describes the steps that have to be executed
frequently when using the product.
5.1 Switching the instrument
on/off
²Switching the instrument on:
iPress .
- The current reading is shown
²Switching the instrument off:
iPress and hold (for approx. 2 s) until the display
goes out.
deenfresitptsvnl????
5. Operation24
5.2 Switching the display
light on/off
²Switching the display light on/off:
The instrument is switched on.
iPress .
5.3 Performing settings
1To open configuration mode:
The instrument is switched on and is in measurement
view. Hold,Max or Min are not activated.
iPress and hold (for approx. 2 s) until the display
changes.
- The instrument is now in configuration mode.
You can change to the next function with .
You can leave configuration mode at any time. To do
so, press and hold (for approx. 2 s) until the
instrument has changed to measurement view. Any
changes that have already been made in configuration
mode will be saved.
2To set Auto Off:
Configuration mode is opened, AutoOff is flashing.
iSelect the desired option with / and confirm
with :
·on: The measuring instrument switches off
automatically if no key is pressed for 10 min.
Exception: A recorded reading is shown on the
display (Hold or Auto Hold is lit).
· oFF: The measuring instrument does not switch
itself off automatically.
6. Measuring 25
3To reset:
Configuration mode is opened, RESET is lit.
iSelect the desired option with / and confirm
with :
·no: Instrument is not reset.
· Yes: Instrument is reset. The instrument is reset to
the factory settings.
- The instrument returns to measurement view.
6. Measuring
This chapter describes the steps that are required to
perform measurements with the product.
²Setting the material characteristic curve:
1Switch between the display of wood moisture (F) and
building moisture (M): or press .
2Select the desired option with or and confirm
with :
Display Category Example
F 1 Softwood lumber Spruce, larch, cherry, pine, poplar, meranti
F 2 Hardwood lumber Beech, oak, maple, ash, Douglas-fir,
walnut, birch
F 3 Chipboard
M 1 Cement screed
M 2 Anhydrite screed
M 3 Concrete
M 4 Solid brick
M 5 High-insulating brick
M 6 Limestone
M7 Gas concrete
CAL Testing characteristic Not for on-site measurements!
deenfresitptsvnl????
Inhaltsverzeichnis
Andere TESTO Messgerät Handbücher
TESTO
TESTO Saveris Bedienungsanleitung
TESTO
TESTO 416 Bedienungsanleitung
TESTO
TESTO 310 Bedienungsanleitung
TESTO
TESTO 512-1 Bedienungsanleitung
TESTO
TESTO 550 Bedienungsanleitung
TESTO
TESTO 6457 Bedienungsanleitung
TESTO
TESTO 606-1 Bedienungsanleitung
TESTO
TESTO 523 Bedienungsanleitung
TESTO
TESTO 320 Bedienungsanleitung
TESTO
TESTO 420 Bedienungsanleitung
TESTO
TESTO 350 Maritime V2 Bedienungsanleitung
TESTO
TESTO 330 Bedienungsanleitung
TESTO
TESTO 540 Bedienungsanleitung
TESTO
TESTO 0638 1345 Bedienungsanleitung
TESTO
TESTO 417 Bedienungsanleitung
TESTO
TESTO 316-1 Bedienungsanleitung
TESTO
TESTO 300 Bedienungsanleitung
TESTO
TESTO 816 Bedienungsanleitung
TESTO
TESTO 425 Bedienungsanleitung
TESTO
TESTO 425 Bedienungsanleitung
