Texecom Premier 24 Bedienungsanleitung

Veritas User Guide Quick Reference Guide

1 INS167

USER GUIDE

Security Control Panels

Issue 2

THANK YOU FOR VOTING TEXECOM

Overview Premier Series User Guide

2 INS221

1. Overview

Introduction

Users of the alarm system will be assigned a unique 4, 5 or 6 digit User code. User

codes are used to arm and disarm the system. Some User codes can also access

additional options such as, system tests and omitting zones.

Keypads will be installed throughout the premises, usually one at each entry/exit door.

The keypads are used to perform all of the system operations i.e. Arming, Disarming etc.

Most User codes can be used at any keypad on the system. However, Local Users will only

be able to use certain keypads on the system.

The Emergency Keys

In case of emergency, the alarm system can provide three immediate emergency alarms

by pressing and holding two specific keys for two seconds.

The emergency keys can be enabled/disabled for each keypad on the system.

The Panic alarm can be programmed for either audible or silent operation.

The Panic alarm can be programmed for either instant or delayed operation.

Emergency Alarm Press Keys

Panic Alarm (PA) !&"

Fire #&$

Medical %&&

The Quick Arm Keys

The ‘Quick Arm’ keys allow the system to be armed without having to enter a User code first.

The ‘Quick Arm’ keys will only work if the keypad has been programmed to allow

arming in this way.

To FULL arm the system, press

To PART arm the system, press

(

followed by

)

Keypad Lock

The keys on the keypad can be locked to prevent unwanted access to the system.

The Emergency keys will NOT operate with the keys locked.

To Lock the keys, press

and

together.

To Unlock the keys, press

and

together again.

Premier SeriesUser Guide Overview

INS221 3

LED Indicators

Five LED indicators have been provided to indicate the status of the system.

LED Status Meaning

Power On AC mains is present on the control panel

Flashing AC Mains is not present, the control panel is running on the standby battery

Service On The system requires attention, contact your installer

Off The system does NOT require attention

Ready On All zones are secure and the system is ready to be armed

Off One or more zones are active

Flashing The system has zones (with the ‘Force Omit’ attribute) that are active

Info. On The system is armed (can also be programmed for other indications)

Off The system is unarmed (can also be programmed for other indications)

Omit On One or more zones are omitted

Off No zones are omitted

Zone Faults During Arming

Before attempting to arm the system, ensure that the premises are secure (all doors and

windows closed etc.) and the Ready light is on.

If an attempt is made to arm the system with any zones active (e.g. door ajar, open

window, etc.) the internal sounders will bleep repeatedly (fault tone) and the display will

show the zones that are active.

The fault tone will stop and the exit tone will resume when all zones are secure. If it is

necessary to leave a zone open then it must be omitted (see page 8 for details).

If an active zone cannot be secured then it may be ‘in fault’, in this case contact

the alarm company immediately.

Arm Fail - Failing to Arm

If the exit procedure is started and zones are still ‘Active’ at the end of the exit procedure,

an Internal alarm will occur (internal sounders only) and the strobe light on the external

sounder will flash.

If this occurs the arm fail must be cleared and the zone in fault identified before the

system can be armed (see page 6 for details on clearing an Arm Fail).

The Ready LED

To help prevent faults during arming a Ready light has been provided, see table above

for details on how the Ready LED operates.

Operating the Alarm System Premier Series User Guide

4 INS221

2. Operating the Alarm System

To FULL Arm the System

The system is FULL Armed when ALL zones are ON (not omitted).

Your Installer may have programmed the system so that it can be set by just pressing

, if this is the case then there is no need to enter the User code below.

1. Ensure that the premises are secure (all doors and windows closed etc.) and the

Ready light is on

2. Enter a valid User code

,,,,

3. Press

to arm

The exit tone will sound

4. Leave the premises

When the system has armed the exit tone will stop

To PART Arm the System

The system is PART Armed, when ONE OR MORE zones have been left OFF (omitted)

i.e. the landing or a bedroom.

The system is only Part Armed when zones are omitted using the ‘Part Arm’ procedure

(omitting zones manually (see page 8 for details) is not classed as Part Arming).

The bottom line of the display is programmable for each Part Arm.

Your Installer may have programmed the system so that it can be Part Armed by

just pressing

(

followed by

)

, if this is the case then there is

no need to enter the User code below.

1. Ensure that the premises are secure (all windows and doors not being omitted are

closed) and the Ready light is on

2. Enter a valid User code

,,,,

3. Press

)

4. Use keys

to select the required Part Arm

5. Press

to arm normally or press

to arm silently

The exit tone will sound (if silent arm has not been selected)

6. Leave the protected area

When the system has armed, the exit tone (if sounding) will stop

Premier SeriesUser Guide Operating the Alarm System

INS221 5

To ARM Individual Areas

If the system has been split up into separate areas of protection i.e. Area 1 = House,

Area 2 = Garage, Area 3 = Shed etc. These areas can be individually selected for FULL

or PART arming as required.

Areas are selected by using keys

(the

key can also be used to

select an area followed by

Only areas that exist on the system can be selected. (A ‘Star’ means the area can

be selected and a ‘Dot’ means the area cannot be selected).

Pressing

will select/deselect all areas, pressing

will toggle between the

first 8 areas and the second 8 areas (where applicable).

1. Ensure that the premises are secure (all windows and doors not being omitted are

closed) and the Ready light is on

2. Enter a valid User code

,,,,

3. Press

4. Use keys

to select the required areas

5. Press

to FULL arm the areas

5. Press

(

followed by

to PART arm the areas

The exit tone will sound (if silent arm has not been selected)

6. Leave the premises

When the system has armed, the exit tone (if sounding) will stop

To DISARM the System

The entry time is divided into two sections, the Entry time and the 2

Entry time. If the

Entry time expires, an Internal alarm will occur and the 2

Entry time will start. If the 2

Entry time expires, an Intruder alarm will occur (all internal and external sounders).

It is perfectly normal for the 2

Entry time to be programmed as zero, in which

case, an Intruder alarm will occur as soon as the Entry time expires.

1. Enter the premises via the designated entry point

The entry tone will start

2. Enter a valid User code

,,,,

The entry tone will stop

Operating the Alarm System Premier Series User Guide

6 INS221

To DISARM the System When Not in Entry

1. Enter a valid User code

,,,,

2. Press

To CANCEL the Exit Mode

Once the exit mode has been started you should leave the premises immediately,

however, if for some reason you decide not to leave, the exit mode must be cancelled.

1. Enter a valid User code

,,,,

2. Press

The exit tone will stop.

To CLEAR an Arm Fail

When the system tries to arm with zones active (open), the internal sounders will sound

and the external strobe will be flashing to indicate a problem. For details on preventing

an Arm Fail condition, please refer to page 3.

If you were not present when the Arm Fail occurred or you do not clear the Arm

Fail, the internal sounders will continue to sound and the external strobe will

continue to flash.

1. Enter a valid User code

,,,,

The internal and external sounders will stop, the external strobe will continue to flash

and the number of the zone that caused the Arm Fail will be displayed.

2. Enter a valid User code

,,,,

and press

To SILENCE an Alarm

When an alarm occurs on the system, the internal and external sounders will normally

sound for a pre-programmed time (normally 15 minutes).

If you were not present when the alarm activated, the internal and external

sounders may have already stopped but the external strobe will still be flashing.

When alarm information is being displayed, pressing the SCROLL key will slow

down the display and also allow manual scrolling through the events.

1. Enter a valid User code

,,,,

The internal and external sounders will stop and the number of the zone that caused the

alarm will be displayed.

The alarm now needs to be reset.

Premier SeriesUser Guide Operating the Alarm System

INS221 7

To RESET After an Alarm

USER Reset

Once the alarm has been silenced (see page 6 for details), the system will need to be reset.

If the system has been programmed, to be reset by an Engineer, pressing

will

not return the display to normal, if this is the case see ENGINEER Reset for details.

The system may have been programmed to be reset by Anti-code, if this is the

case, see ANTI-CODE Reset for details.

1. Enter a valid User code

,,,,

2. Press

The external strobe will stop, the system will chime and the display will return to normal.

ENGINEER Reset

If the system has been programmed to be reset by an Engineer following an alarm

activation, you will still be able to silence the alarm by entering a valid User code (see

page 6 for details).

The system cannot be armed again until the alarm has been reset.

1. Contact the telephone number on the display (if programmed) or the telephone

number on the last page of this User Guide

ANTI-CODE Reset

If the system has been programmed to be reset using an Anti-Code following an alarm

activation, you will still be able to silence the alarm by entering a valid User code (see

page 6 for details).

The system cannot be armed again until the alarm has been reset.

1. Enter a valid User code

,,,,

2. Press

The display will show a random code number i.e. 4281.

3. Contact the telephone number on the display (if programmed) or the telephone

number on the last page of this User Guide and quote the random code number

You will be given a 4-digit Anti-Code i.e. 5624.

4. Enter the Anti-code that has been given to you

,,,,

5. Press

If the Anti-code is correct, the keypad will bleep to indicate that the system has been

reset and the display will return to normal.

Operating the Alarm System Premier Series User Guide

8 INS221

To OMIT Zones

It is possible to exclude (omit) individual zones when arming i.e. if a zone is ‘in fault’. Users

with access to this function can only omit zones that have been programmed as ‘Omittable’.

If the zone can be omitted, there will be a ‘Star’ to the right of the zone number.

Only zones that have the ‘Omit’ attribute assigned to them can be omitted.

A ‘Star’ will appear to the left of the zone number to indicate that the zone has been

selected for omitting.

All omitted zones will be automatically reinstated the next time the system is

disarmed, unless programmed otherwise.

To re-instate zones manually, simply follow the instructions again. However, when

the

key is pressed on this occasion, the zones will be re-instated.

1. Enter a valid User code

,,,,

and press

2. Enter the zone number

,,,

3. Press

to omit the selected zone

Repeat for other zones if required.

4. Press

when finished

Continue to arm the system as normal.

The Turn CHIME On and Off

The system can be set up so that activating (opening) certain zones will cause the

internal sounders to chime. This would normally be used on a front door, exit button etc.

Zones will only cause the internal sounders to chime if they are selected for chime

(see page Master User Guide for details on selecting which zones chime).

Once a zone has been selected for chime, the Chime facility can be manually turned on

and off as required.

The system can also be programmed to automatically turn chime on and off under

certain conditions i.e. certain times of the day, door left open etc.

If no zones have been programmed for Chime, then turning Chime on and off will

have no effect.

To turn CHIME On To turn CHIME Off

1. Press

The Chime tone will sound. The Error tone will sound.

Premier SeriesUser Guide Operating the Alarm System

INS221 9

To CHANGE Your User Code

Users with access to this option can change their own User codes. User codes are

unique to each user and can be 4, 5 or 6 digits long.

Only the User code that is entered to access the change code menu will be changed.

Before changing your code, it is vital that you memorise or write down the new

code you are about to program. Failure to remember your code will require an

engineer visit to re-program a new code for you. This may incur a call-out charge.

1. Enter the User code that requires changing

,,,,

2. Press

3. Press

4. Press

(

5. Press

6. Enter a new 4, 5 or 6-digit User code

,,,,

7. Press

to accept the new code

8. Press

to exit the menu

The display will return to normal.

Quick Reference Guide Premier Series User Guide

10 INS221

4. Quick Reference Guide

Operation Description Action

To Full Arm the System Enter a valid User code ,,,,

Press Yes (or press Chime to arm silently) *or -

To Part Arm the System Enter a valid User code ,,,,

Press Part )

Select Required Part Arm !,(

Press Yes (or press Chime to arm silently) *or -

To Arm Individual Areas Enter a valid User code ,,,,

Press Area '

Select Required Area using keys 1 - 8 !

Press Yes (or press Chime to arm silently) *or -

To Disarm the System Enter a valid User code ,,,,

Press Yes (if the entry mode was not started) *

To Cancel the Exit Mode Enter a valid User code ,,,,

Press Yes *

To Clear an Arm Fail Enter a valid User code ,,,,

Press Reset 1

To Silence an Alarm Enter a valid User code ,,,,

To Reset After an Alarm Enter a valid User code ,,,,

Press Reset 1

To Engineer Reset Contact Your Installation Company _____________

To Anti-code Reset Enter a valid User code ,,,,

Press Reset 1

Contact Your Alarm Receiving Centre _____________

Quote 4-digit code shown on display !"#$%&'(((('

Enter 4-digit code given by Receiving Centre ,,,,

Press Yes *

To Omit Zones Enter a valid User code ,,,,

Press Omit 3

Enter Zone Number(s)

,,,…

Press Menu when finished 3

Press Yes to Arm *

Turn Chime On/Off Press Chime Once to Turn ON -

Press Chime Again to Turn OFF -

To Change User Code Enter a valid User code ,,,,

Press Menu followed by Yes 4*

Press 2 followed by Yes (*

Enter a new 4, 5 or 6 digit User code ,,,,

Press Yes to accept *

Press Reset to return to the normal display 1

Andere Handbücher für Premier 24

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Texecom Bedienfeld Handbücher

Texecom

Texecom Veritas 8 Bedienungsanleitung

Texecom

Texecom Premier 412 Bedienungsanleitung

Texecom

Texecom Premier 8SP Bedienungsanleitung

Texecom

Texecom Premier 412 Bedienungsanleitung

Texecom

Texecom PREMIER 48 Bedienungsanleitung

Texecom

Texecom Veritas R8Plus Bedienungsanleitung

Texecom

Texecom Premier 8168 Bedienungsanleitung

Texecom

Texecom Premier Elite ComIP Bedienungsanleitung

Texecom

Texecom Premier 412 Premier 816 Premier 832 Bedienungsanleitung

Texecom

Texecom Premier Elite 88 Bedienungsanleitung

Texecom

Texecom Veritas Excel Master Bedienungsanleitung

Texecom

Texecom Veritas R8 Plus Bedienungsanleitung

Texecom

Texecom Premier Elite 48-W Bedienungsanleitung

Texecom

Texecom Premier 832 Bedienungsanleitung

Texecom

Texecom Premier Elite Series Bedienungsanleitung

Texecom

Texecom Premier 8SP Bedienungsanleitung

Texecom

Texecom Premier 24 Gebrauchsanweisung

Texecom

Texecom Veritas 8 Bedienungsanleitung

Texecom

Texecom Premier Elite 48-W Bedienungsanleitung

Texecom

Texecom PREMIER 48 Bedienungsanleitung

Texecom

Texecom Premier 24 Montage- und Bedienungsanleitung

Texecom

Texecom Premier Elite Micro Contact-W Bedienungsanleitung

Texecom

Texecom Premier 412 Bedienungsanleitung

Texecom

Texecom Veritas 8 Bedienungsanleitung

Beliebte Bedienfeld Handbücher anderer Marken

RDZ

RDZ PC-HRX Bedienungsanleitung

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Technisches Handbuch

Efka

Efka Variocontrol V810 Bedienungsanleitung

Cebora

Cebora 208-10 Bedienungsanleitung

AMX

AMX AutoPatch CP-15 Bedienungsanleitung

Satel

Satel CA-6 KLED-S Bedienungsanleitung

Evolution

Evolution IQ plus 800 Bedienungsanleitung

Fagor

Fagor 8040 TCO CNC Bedienungsanleitung

Trane

Trane ComfortLink II XL950 Control Bedienungsanleitung

AKO

AKO PROCool AKO-17635-2 Bedienungsanleitung

ABB

ABB 6136/30M-101 Bedienungsanleitung

Telikou

Telikou BK-603 Belt Pack Bedienungsanleitung

Mapei

Mapei Mapeheat Thermo Touch Bedienungsanleitung

Bosch

Bosch D9412GV4 Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Bedienungsanleitung

Sminn

Sminn BOX L VF1L EI Bedienungsanleitung

Balboa

Balboa TP600 Bedienungsanleitung

Nice

Nice HSCU1 Technische Daten