Texecom Veritas R8Plus Bedienungsanleitung

o400

MASTER USER GUIDE

For Service Call Scorpion Group Security - 01452 525397

THANK YOU FOR VOTING TEXECOM

Assigning Access Codes Master User Guide

2 INS140-2

Master User Guide

Assigning Access Codes

The control panel allows up to eight users to operate the alarm system,

each user is assigned an “Access code”, “Access Level” and “User

Number”. The figure below shows an example of users assigned to

a typical alarm system:

User Number

Each user is identified by the alarm system as User 1 through to User 8.

Access Code

Each user has a programmable 4 digit Personal Access code which the

user enters in order to operate the alarm system.

Access Level

Each user has a programmable Access Level that determines how the

alarm system responds and which of the system facilities the user can

access.

Each Access Level has an associated number (1 – 8) which is used

when programming the Access Level of a user.

User Number:1

ccess Code:

ccess Level:

Access Type:

4321

Boss Engineer

Installer

User Number:2

ccess Code:

ccess Level:

Access Type:

????

Master User

Customer

User Number:3

ccess Code:

ccess Level:

Access Type:

5678

User

Customer

User Number:8

ccess Code:

ccess Level:

Access Type:

2580

Cleaner

Customer

4...7

Master User Guide Assigning Access Codes

INS140-2 3

There are eight possible User Access Levels:

User !

A User may set, unset, silence an alarm and reset the system. In

addition a User can test the system outputs, perform a walk test and

view the event log. A User cannot change Access codes (other than

their own) or Access Levels.

Engineer "

Engineers cannot change Access Levels or Access codes (other than

their own). However they can access all system programming options.

Personal Attack #

Entering a PA code will cause an immediate alarm, sounding both the

internal and external sounders.

Duress $

A Duress code behaves exactly as a User code (Level 1) but will in

addition activate the Duress channel on the communicator interface to

secretly summon assistance.

Master User %

A Master User may set, unset, silence an alarm and reset the system. In

addition a Master can test the system outputs, perform a walk test and

view the event log. A Master User can also assign new user Access

code and Access Levels.

Cleaner &

If the system is full set or part set then a Cleaner code will automatically

omit the Cleaner Suite zones without affecting the other zones. In

addition pressing a key will NOT cause the system to start entry mode.

On leaving, the cleaner should enter their Access code '''' and

press either (or ). The *key is disabled and the previous

set will be restored irrespective of which key was pressed. A cleaner

cannot access Chime. Nor can they cancel an alarm or reset the

system.

Assigning Access Codes Master User Guide

4 INS140-2

1. When a cleaner is Setting the system the Cleaner Suite zones

will flash indicating that they are currently omitted but are about

to be re-included. Any other omitted zones (e.g. if the system

was previously part set rather than full set) will also flash but will

NOT be included.

2. If the system is unset then a cleaner can full set, part set and

omit zones.

Null +

The Null level is the only level which can be changed both by a Master

User and by a Boss Engineer. The Null level has two functions:

1. If a user is no longer required, its Access Level should be

changed to Null. This will erase the associated Access code.

2. To change a Customer Access Type to an Installer Access Type,

or vice versa, it must first be changed to the Null level.

Boss Engineer ,

Boss Engineers cannot change Customer Access Levels or Customer

Access codes. They can only change Installer Access Levels and

Installer Access codes. Boss Engineers can also access all system

programming options.

Access Type

There are two Access Types, Customer and Installer. The Boss Engineer

level can only program the Installer Types. The Master User Level can

only program the Customer Types.

The table below shows a summary of each Access Level and who is

responsible for assigning the level:

Access Level Access Level

Number Access

Type Can be Programmed

User !Customer Master $#"!

Engineer "Installer Boss ''''

PA (Panic) #Customer Master $#"!

Duress $Customer Master $#"!

Master User %Customer Master $#"!

Cleaner &Customer Master $#"!

Null +Customer

Installer

Master $#"!

Boss ''''

Boss Engineer ,Installer Boss ''''

Master User Guide Programming Access Codes

INS140-2 5

Programming Access Codes

Each user has a programmable 4 digit Access code which the user

enters in order to operate the alarm system.

Changing Your Own Access Code &-

Every user has the ability to change their own 4 digit Access code, as

follows:

From the Unset State:

1) Enter your existing Access code ''''

2) Press PROG to access the Programming Menu .

3) Enter 60 to select the Change Your Access code option &-

4) Enter your new 4 digit Access Code ''''

5) Press PROG, the system will chime to confirm your new code .

6) Press RESET to revert to the unset state /

Assigning a New Access Code &! – &,

The Master User can assign a new Access code or change an existing

Access code providing it is a Customer Type. The Boss Engineer can

assign a new Access code or change an existing Access code providing

it is a Installer Type.

From the Unset State:

1) Enter your Access code (Master User or Boss Engineer only) ''''

2) Press PROG to access the Programming Menu .

3) Enter 6 to select the Change Access code option &

4) Enter the User Number (1 - 8) you wish to change, e.g. 5 %

5) Enter their new 4 digit Access code ''''

6) Press PROG, the system will chime to confirm the new code .

7) Press RESET to revert to the unset state /

Displaying Your User Number &0

Each user is identified by the alarm system as User 1 through to User 8.

Every user may view their User Number (1 - 8) as follows:

Programming Access Codes Master User Guide

6 INS140-2

From the Unset State:

1) Enter your Access code ''''

2) Press PROG to access the Programming Menu .

3) Enter 69 to select the View Your User Number option &0

4) The zone light corresponding to your User Number will illuminate

5) Press RESET, the system will return to the Programming Menu /

6) Press RESET to revert to the unset state /

Changing Access Levels +! –+,

Each Access Level has an associated Number (1 –8) as follows:

Access Level Access Level

Number Access

Type Can be Programmed

User !Customer Master $#"!

Engineer "Installer Boss ''''

PA (Panic) #Customer Master $#"!

Duress $Customer Master $#"!

Master User %Customer Master $#"!

Cleaner &Customer Master $#"!

Null +Customer

Installer

Master $#"!

Boss ''''

Boss Engineer ,Installer Boss ''''

The Master User can only assign Customer Access Types and the

Boss Engineer can only assign Installer Access Type.

From the Unset State:

1) Enter your Access code (Master User or Boss Engineer only) ''''

2) Press PROG to access the Programming Menu .

3) Enter 7 to select the Change Access Level option +

4) Enter the User Number (1 - 8) you wish to change, e.g. 5 %

5) Enter their new Access Level (1 - 8) e.g. 4 = Duress $

6) Press PROG, the system will chime to confirm the new Access Level .

7) Press RESET to revert to the unset state /

Master User Guide Programming Access Codes

INS140-2 7

Displaying Your Access Level +0

Every user may view their own Access Level

From the Unset State:

1) Enter your Access code ''''

2) Press PROG to access the Programming Menu .

3) Enter 79 to select the View Your Access Level option +0

4) The zone light corresponding to your Access Level will illuminate

5) Press RESET, the system will return to the Programming Menu /

6) Press RESET to revert to the unset state /

For security reasons the Duress Access Level will be displayed as

the User Access Level.

Noteswww.scorpion-group.co.uk

Code Table Master User Guide

INS140-2 For Service Call Scorpion Group Security - 01452 525397 - www.scorpion-group.co.uk

Code Table

User

No. User

Name

Default

Access

Code

Option to

Change

Access

Code

New

Access

Code

Default

Access

Level

Option to

Change

Access

Level

New

Access

Level

1$#"! &! %Master +!

2'''' &" ,Boss +"

3N/A &# +Null +#

4N/A &$ +Null +$

5N/A &% +Null +%

6N/A && +Null +&

7N/A &+ +Null ++

8N/A &, +Null +,

1. Customer codes can only be programmed when the

Programming Menu is accessed using a Master User code.

2. Installer codes can only be programmed when the

Programming Menu is accessed using a Boss Engineer code.

Access Level Access Level

Number Can be Programmed by

User !Master $#"!

Engineer "Boss ''''

PA #Master $#"!

Duress $Master $#"!

Master User %Master $#"!

Cleaner &Master $#"!

Null +Master $#"!

Boss ''''

Boss Engineer ,Boss ''''

Inhaltsverzeichnis

Andere Texecom Bedienfeld Handbücher

Texecom

Texecom Premier 832 Bedienungsanleitung

Texecom

Texecom Premier 888 Bedienungsanleitung

Texecom

Texecom Veritas 8 Bedienungsanleitung

Texecom

Texecom Premier Elite 48-W Bedienungsanleitung

Texecom

Texecom Veritas R8 Plus Bedienungsanleitung

Texecom

Texecom Veritas 8 Bedienungsanleitung

Texecom

Texecom Premier 412 Bedienungsanleitung

Texecom

Texecom Premier 8168 Bedienungsanleitung

Texecom

Texecom Premier 412 Bedienungsanleitung

Texecom

Texecom PREMIER 48 Bedienungsanleitung

Texecom

Texecom Premier 412 Bedienungsanleitung

Texecom

Texecom Veritas R8 Plus Bedienungsanleitung

Texecom

Texecom Premier Elite 88 Bedienungsanleitung

Texecom

Texecom Premier 24 Gebrauchsanweisung

Texecom

Texecom Premier 24 Bedienungsanleitung

Texecom

Texecom Premier Elite Series Bedienungsanleitung

Texecom

Texecom Premier 24 Bedienungsanleitung

Texecom

Texecom Premier 24 Bedienungsanleitung

Texecom

Texecom PREMIER 48 Bedienungsanleitung

Texecom

Texecom Premier Elite Micro Contact-W Bedienungsanleitung

Texecom

Texecom Premier Elite ComIP Bedienungsanleitung

Texecom

Texecom Veritas 8 Bedienungsanleitung

Texecom

Texecom Premier 8SP Bedienungsanleitung

Texecom

Texecom Premier 412 Bedienungsanleitung

Beliebte Bedienfeld Handbücher anderer Marken

RDZ

RDZ PC-HRX Bedienungsanleitung

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Technisches Handbuch

Efka

Efka Variocontrol V810 Bedienungsanleitung

Cebora

Cebora 208-10 Bedienungsanleitung

AMX

AMX AutoPatch CP-15 Bedienungsanleitung

Satel

Satel CA-6 KLED-S Bedienungsanleitung

Evolution

Evolution IQ plus 800 Bedienungsanleitung

Fagor

Fagor 8040 TCO CNC Bedienungsanleitung

Trane

Trane ComfortLink II XL950 Control Bedienungsanleitung

AKO

AKO PROCool AKO-17635-2 Bedienungsanleitung

ABB

ABB 6136/30M-101 Bedienungsanleitung

Telikou

Telikou BK-603 Belt Pack Bedienungsanleitung

Mapei

Mapei Mapeheat Thermo Touch Bedienungsanleitung

Bosch

Bosch D9412GV4 Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Bedienungsanleitung

Sminn

Sminn BOX L VF1L EI Bedienungsanleitung

Balboa

Balboa TP600 Bedienungsanleitung

Nice

Nice HSCU1 Technische Daten