Texecom Premier 412 Bedienungsanleitung

MASTER USER MANUAL

Security Control Panels with Integrated

Communicator

Issue 5

THANK YOU FOR VOTING TEXECOM

THANK YOU FOR VOTING TEXECOMTHANK YOU FOR VOTING TEXECOM

THANK YOU FOR VOTING TEXECOM

Contents Premier 412 & 816 Master User Manual

2 INS141-5

Contents

1. About the Alarm System ............................. 3

Introduction ......................................................................3

About this Manual............................................................ 3

Fire Detection................................................................... 3

Monitoring ........................................................................ 3

Zones and Partitions........................................................ 3

Access Codes.................................................................. 3

Remote Keypads ..............................................................4

Keypad Types.................................................................. 4

Keypad Layouts ............................................................... 4

Function Keys .................................................................. 5

Emergency Keys.............................................................. 5

2. Operating the Alarm System ...................... 6

Introduction ......................................................................6

Access Codes.................................................................. 6

Arming & Disarming the Alarm System...........................6

Checking if the System is Ready to Arm ........................ 6

Away Arming.................................................................... 6

Stay Arming...................................................................... 6

Cancelling the Arming Process....................................... 7

Disarming During Entry ................................................... 7

Disarming when not in Entry ........................................... 7

Disarming after an Alarm................................................. 7

Auto Stay Arming............................................................. 7

Changing from Delayed to Instant Stay.......................... 7

Arming and Disarming Partitions ....................................8

Away Arming Partitions ................................................... 8

Stay Arming Partitions ..................................................... 8

Disarming Partitions......................................................... 8

Changing to another Partition ......................................... 9

Bypassing Zones..............................................................9

Manually Bypassing Zones ............................................. 9

Unbypassing Zones......................................................... 9

Group Bypass.................................................................. 9

Quick Bypass and Arm.................................................. 10

3. User Functions Menu ................................ 11

Reset Alarms ..................................................................11

Last Alarm Log ...............................................................11

Service Faults................................................................. 11

Acknowledging a New Service Fault ............................ 11

View Service Faults........................................................ 11

Anti-code Reset..............................................................12

Toggle Chime On and Off ..............................................12

Change User Code.........................................................13

View Log (LCD Only)...................................................... 13

Abort Communications ..................................................13

4. System Program Menus ........................... 14

Programming Text (LCD Only)...................................... 14

Programming Users .......................................................15

Program User ............ 16

User Options 1 ............ 16

User Options 2 ............ 16

User Options 3 ............ 17

User Text (LCD Only) ............ 17

System Tests & Utilities .................................................18

Walk Test ............ 19

Test Speakers & Outputs ............ 19

Send Test Call ............ 19

Enable Download/Engineer Access ............ 19

Start Call Back ............ 19

Program Time ............ 19

Program Date .............19

Program Banner Text (LCD only) .............19

Print 100 Events .............19

5. Fire Safety & Maintenance ....................... 20

Fire Safety.......................................................................20

Fire Alarm Operation ......................................................20

Household Fire Safety Audit ..........................................20

Fire Escape Planning .....................................................20

Maintenance ...................................................................21

Glossary..........................................................................21

6. Installation Records ................................. 22

Control Panel..................................................................22

Keypads..........................................................................22

Timers .............................................................................22

Zones ..............................................................................22

Users...............................................................................23

Notes...............................................................................23

DO NOT REMOVE COVER



MAINS VOLTAGES INSIDE

No user serviceable parts, servicing by qualified

personnel only.

Premier 412 & 816 Master User Manual About the Alarm System

INS141-5 3

1. About the Alarm System

Introduction

Your alarm system consists of a control panel, one or more

keypads and various detectors and sensors. The control

panel will normally be mounted out of sight in a utility room

or basement etc. The control panel houses the system’s

electronics and stand-by battery. There is normally no

reason for anyone except an installer or service person to

have access to the control panel.

The remote keypad is used to send commands to the

system and to display the current system status via the

various coloured lights (LED’s). The keypad also provides

audible feedback each time a key is pressed. Each keypad

will be mounted in convenient locations inside the protected

premises, near designated points of entry/exit.

Read this manual carefully and have your installer instruct

you on your system’s operation. Become familiar with the

features that have been implemented on your system. All

users of this system should be equally instructed in its use.

About this Manual

This manual is a thorough explanation of all system

functions, including troubleshooting and programming

Access codes in addition to performing basic system

functions. Most users of the system will not need to know all

of this information. The section of this manual, titled

“Operating your Alarm System” explains general system

concepts and instructs the user on how to arm and disarm

the system and bypass zones. The remaining sections of the

manual are reserved for more detailed system information.

Fire Detection

This equipment is capable of monitoring fire detection

devices such as smoke detectors and providing a warning

alarm if a fire condition is detected. Good fire detection

depends on having adequate numbers of fire detectors

placed in appropriate locations. This equipment should be

installed in accordance with the relevant local authority fire

regulations. Carefully review the “Fire Escape Planning”

guidelines in this manual.



Your installer must enable the fire detection feature of

this equipment before it will work.

Monitoring

This system is capable of transmitting alarms, troubles and

emergency information over telephone lines to an alarm

monitoring station. If you inadvertently initiate an alarm,

immediately call the Alarm Receiving Centre (ARC) to

prevent an unnecessary response.



Your installer must enable the monitoring function

before it will work.

Zones and Partitions

Your installer has divided the protected premises into zones

and partitions. A zone is an area of protection that has one

or more detection sensors connected to it (motion detectors,

glass-break detectors, door contacts or shock sensors). A

single zone might be a room, a hallway or a door or window.

Two or more of these zones will be linked together by the

control panel to form a partition.

A partition is an area of the protected premises. A partition

can be armed and disarmed independently from other

partitions. All of the partitions together form the entire alarm

system. If your alarm system is not divided into partitions

then all devices will be assigned to Partition 1.

Some zones may belong to more than one partition, such as

points of entry/exit and hallways. These are called Global

Zones because they are not assigned to a single partition.

The following table shows the number of zones and

partitions for the Premier 412 &816 control panels:

Control Panel Partitions Zones Zones (max)

Premier 412 2 4 12

Premier 816 4 8 16

Access Codes

As a user of the alarm system, you will be assigned a 4, 5 or

6 digit Access code. Access codes are used to arm and

disarm the partition(s) to which they are assigned. Some

Access codes can perform additional system functions,

such as programming system options, bypassing zones and

performing system tests.

Your Access code may not allow you to access certain

system functions. For instance, if your code is only allowed

to arm and disarm Partition 1, you will not be able to arm or

disarm other partitions, or the entire system.

Your Access code may also be programmed for Global

Access. A Global Access code can be used at any keypad

and will allow you to arm and disarm any of the partitions

assigned to your code. Alternatively your code may be

programmed for Partition Access. A Partition Access code

will only allow you to arm and disarm the partitions that are

assigned to both the keypad and your code.

About the Alarm System Premier 412 & 816 Master User Manual

4 INS141-5

Remote Keypads

One or more remote keypads will be installed throughout

the protected premises, usually one at each entry/exit door.

Each remote keypad is normally assigned to the partition

that it is going to control. A keypad can be assigned to more

than one partition, if required (global keypad).

Keypad Types

The following keypad types are available:

Premier RKP4:The Premier RKP4 is styled around the

Premier RKP16. This remote keypad has 4 zone indicator

lights and is designed for use with the Premier 412 control

panel.

Premier RKP8:The Premier RKP8 is styled around the

Premier RKP16. This remote keypad has 8 zone indicator

lights and is designed for use with the Premier 816 control

panel.

Premier RKP16:The Premier RKP16 has 16 zone indicator

lights and is designed for use with the Premier 412 and

Premier 816 control panels when expanded to 12 and 16

zones respectively.

Premier RKP16 Plus:The Premier RKP16 Plus has all the

features of the standard Premier RKP16 plus dedicated

indications for Fire, Bypass, Instant and Stay. It also features

two programmable zone inputs that can be utilised by your

installer for detection devices close to the location of the

remote keypad.

Premier LCD:The Premier LCD has a standard size 32

character back-lit Liquid Crystal Display. It also features two

programmable zone inputs that can be utilised by your

installer for detection devices close to the location of the

remote keypad.

Premier LCDL:The Premier LCDL has a large size 32

character back-lit Liquid Crystal Display. It also features two

programmable zone inputs that can be utilised by your

installer for detection devices close to the location of the

remote keypad.

Keypad Layouts

4ghi

2abc 3def

7pqrs

Area

5jkl

8tuv

6mno

9wxyz

Yes

Disarm

Stay

Arm Bypass

Chime

Reset

Alarm Armed

Service Ready

Stay

Fire

12345678

910 11 12 13 14 15 16

Bypass Instant

456

123

7890

Armed

Zones

Ready

Alarm

Service

ARM

STAY

DISARM

PASS

AREA

Premier RKP4/8/16

Premier RKP16 Plus

ghi

abc

def

pqrs

Area

jkl

tuv

mno

wxyz

Yes

Stay

Chime

Bypass Reset

Bypass Service

Power

Armed

Ready

Premier 816

12:55.22 21/11

Premier LCD/LCDL

Premier 412 & 816 Master User Manual About the Alarm System

INS141-5 5

 - Alarm Light: If an alarm has occurred whilst the

partition/system was armed the Alarm light will illuminate.

The alarm partition/system cannot be Armed until

standing Alarm has been acknowledged/reset (see

“Acknowledging an Alarm” on page 11).

 - Service Light: The Service light will flash when a new fault

occurs and will change to on steady when the fault has

been acknowledged. When the system is free of all faults

the Service light will be off.

The alarm system cannot be armed until the new faults

have been acknowledged (see “Service Faults” on page

11).

 - Armed Light: The Armed light indicates the armed status

of the partition/system. The Armed light is on when the

partitions assigned to the keypad are armed. When the

Armed light is off the partitions are disarmed. The Armed

light will flash as follows:

Partition in Exit: Slow flash (1 second on, 1 second off).

Partition is Delayed Stay Armed: Slow flash (1 second on,

1 second off).

Partition is Instant Stay Armed: Fast flash (200

milliseconds on, 200 milliseconds off).

 - Ready Light: If the Ready light is on the partition/system is

ready for arming. If the Ready light is off, one or more

zones within the partition/system are violated, check the

relevant zones as indicated on the keypads. If the Read

light is flashing, one or more zones are bypassed or are

violated and force-armable.

 - Zone Lights: The zone lights indicate the status of each

alarm zone within the partition. When a zone is violated o

in trouble the relevant zone light will illuminate. When

zone is secure the relevant zone light will be off.

A keypad can be programmed to blank its display after

period of time. An Access code may be required to re-

enable the display. Otherwise simply press any key.

Zone display is always enabled when the alarm system is in

alarm.

 - Function Keys: See “Function Keys”.

 - Fire: if the Fire light is on with no zone indicators

illuminated, then a fire alarm has occurred from one of the

2-wire smoke sensors. If there is an accompanied zone

indication, the fire alarm has occurred from the smoke

sensor on the indicated zone.

 - Bypass: If the Bypass light is on, one or more zones have

been manually bypassed, (see “Manually Bypassing

Zones” on page 9).

 - Stay: If the Stay light is on, the partition/system is in the

stay armed mode. The Armed light will also be flashing.

 - Instant: If the Instant light is on, the partition/system is in

the stay armed mode and the delayed zones (front doo

etc) are instant. The Armed light will also be flashing

rapidly.

$ - Power Light: The power light is on steady when mains

supply is present and flashes when the system is running

on battery (mains fail).

! - LCD Display: 16 character Liquid Crystal Display (LCD).

Function Keys

The remote keypad function keys are described as follows:

Key Function

" The Bypass key is used for either group or manual

bypass of zones (see page 9).

 The Menu key is used to access the more advanced

user functions and programming options.

 The Arm key is used when away arming the system or

partition.

 The Stay key is used when Stay arming the system or

partition.

! The Disarm key is used when disarming the system or

partition.



The Area key is normally used when arming and

disarming a particular partition. When the Area key is

pressed on its own the keypad will indicate the armed

status of all partitions.

The Area key can also be used to temporarily switch

the keypad to a different partition, see page 9.

 The Chime key is used to enable/disable the chime

feature, see page 12.

 The Reset key is used to reset the system after an

alarm or service fault condition, see page 11.

 The Yes key is used to arm the system and to select

menu options.

 The No key is used when disarming the system or

partition.



When a keypad is in use other keypads will be locked-

out except for emergency functions. The lock-out will

persist 4 seconds after the last key is pressed.

Information tones will be limited to the keypad in use.

Emergency Keys

In case of emergency, the alarm system can provide three

immediate emergency alarms by pressing and holding two

specific keys for three seconds.

Emergency Alarm Press Keys

&

&

& 



The emergency keys can be individually enabled or

disabled for each keypad on your alarm system by

the installer.

The Panic alarm can be individually programmed for

either audible or silent operation for each keypad.

Emergency commands are detailed on the inside flap

label of each remote keypad.

Operating the Alarm System Premier 412 & 816 Master User Manual

6 INS141-5

2. Operating the Alarm System

Introduction

Before attempting to operate the alarm system ensure you

have familiarised yourself with all the arming and disarming

methods covered in this section.

Access Codes

• If you make a mistake whilst entering your Access code,

simply enter the correct Access code.

Arming & Disarming the Alarm System

Checking if the System is Ready to Arm

To help prevent faults during arming, a Ready light has

been provided on each keypad. The Ready light works as

follows:

• If the Ready light is on steady then the alarm system is

ready to be armed.

• If the Ready light is flashing then the alarm system has

bypassed zones and/or Force Armable zones that are

violated, check these zones before proceeding.

• If the Ready light is off then one or more zones are

violated, either secure or bypass these zones before

proceeding. The keypads will display the zones that are

violated:

Zone 04 Active

Patio Doors

Armed

Zones

87654321

Ready

Alarm

Service

Zone 01 Active

Front Door

Active zones are scrolled

in sequence on LCD keypads

Active zones are indicated by

the relevant zone lights on

LED Keypads



If any unbypassed zones that are not enabled for

“Force Arming” are violated at the end of the exit

delay this is termed an exit error and the alarm system

will go into fail set state (internal alarm). If

programmed by the installer the external bell will also

sound. Enter a valid user Access code to silence this

alarm.

A zone will only be armed when ALL associated

partitions are armed but will be disarmed when ANY

associated partition is disarmed.

Away Arming

The Away arming mode is normally used when leaving the

premises. When the system is armed in this mode all

detection zones assigned to your partition(s) will be armed.

The Ready light must be on steady before the alarm system

can be Away armed.

➤ To Away arm the alarm system proceed as follows:

Please Exit....

17: 0.21 28/04

YES to Arm?

MENU for Options

The light will flash and the exit tone will sound.

, when the system has armed the

exit tone will stop. The system is now Away armed.

Armed

Leave the premises

Press a

Enter Access code ????

Press y

Armed

Zones

87654321

Ready

Alarm

Service

Armed

Zones

87654321

Ready

Alarm

Service



If the Quick Arm feature is enabled, you can omit step

1 from the above procedure.

Stay Arming

The Stay arming mode is normally used when the premises

will be occupied. When the system is armed in this mode all

Interior detection zones assigned to your partition(s) will be

bypassed. Before Stay arming check the following:

• Secure or bypass any perimeter zones that are violated.

• Ensure no perimeter zones are bypassed

unintentionally.

• Ensure no perimeter Force Armable zones are violated

unintentionally.

➤ To Stay arm the alarm system proceed as follows:

Premier 816

17: 0.21 28/04

YES to Arm?

MENU for Options

The alarm system will arm immediately and the

light will flash.

The system is now Stay armed.

Armed

Press s

Enter Access code ????

Armed

Zones

87654321

Ready

Alarm

Service

Armed

Zones

87654321

Ready

Alarm

Service



If the Quick Arm feature is enabled, you can omit step

1 from the above procedure.

If the system is fitted with a Premier RKP16 Plus then

the Stay light will also illuminate when the system is

Stay armed.

Premier 412 & 816 Master User Manual Operating the Alarm System

INS141-5 7

Cancelling the Arming Process

➤ To cancel the arming process during the exit delay:

Premier 816

17: 0.21 28/04

Armed

Zones

87654321

Ready

Alarm

Service

MENU for Options

NO to Disarm?

Arming has been cancelled and the alarm system is

now disarmed.

Press d

Enter Access code ????

Armed

Zones

87654321

Ready

Alarm

Service

Press n



If the system only has one partition you will not have

to perform step 2.

Disarming During Entry

➤ To disarm the alarm system during entry, proceed as

follows:

Premier 816

08: 1.12 28/04

Armed

Zones

87654321

Ready

Alarm

Service

Enter Your Code

08: 0.59 28/04

The entry tone will stop and the light will turn off.

The alarm system is now disarmed.

Armed

Enter Access code ????

Armed

Zones

87654321

Ready

Alarm

Service

Enter the premises via the designated entry point,

the entry tone will sound. Proceed directly to the

remote keypad.



If a valid Access code is not entered before the end of

the entry delay, an alarm will occur.

Disarming when not in Entry

➤ To disarm the alarm system when not in entry, proceed

as follows:

Premier 816

17: 0.21 28/04

Armed

Zones

87654321

Ready

Alarm

Service

MENU for Options

NO to Disarm?

The light will turn off. The alarm system is now

disarmed.

Armed

Press d

Enter Access code ????

Press n

Armed

Zones

87654321

Ready

Alarm

Service



If the system only has one partition you will not have

to perform step 2.

If the Quick Disarm feature is enabled and the system

is Stay armed you can omit step 1 from the above

procedure.

Disarming after an Alarm

➤ To disarm the alarm system after an alarm, proceed as

follows:

Zone 05 Active

Master Bedroom

Perim 05 Alm

1... 21:10.56 28

The system is disarmed and the keypads display the

source of the alarm.

Enter Access code ????

Armed

Zones

87654321

Ready

Alarm

Service

The system must now be reset before you can arm again,

see page 11 for details on resetting alarms.

Auto Stay Arming

If your installer has enabled the Auto Stay feature the system

will automatically Stay arm if the entry/exit zone (front door)

is not activated whilst attempting to Away arm the system.

➤ To auto Stay arm your alarm system proceed as follows:

Please Exit....

17: 0.21 28/04

YES to Arm?

MENU for Options

The light will flash and the exit tone will sound.Armed

Do NOT leave the premises during the exit delay. At

the end of the exit delay the alarm system will Stay arm.

Press a

Enter Access code ????

Press y

Armed

Zones

87654321

Ready

Alarm

Service

Armed

Zones

87654321

Ready

Alarm

Service

Changing from Delayed to Instant Stay

When Stay arming the system the delayed zones (front door

etc) are normally delayed, i.e., when a delayed zone is

violated it will start the entry delay timer. However, it is

possible to change the delayed zones to instant when the

system is in a Stay armed mode. If a delayed zone is

violated when the system is in the “Instant Stay” mode the

system will generate an alarm immediately.

➤ To change from Delayed Stay to Instant Stay, proceed

as follows:

INSTANT STAY

17: 0.21 28/04

The light will flash quickly.

The system is armed.

Armed

Instant Stay

Press and hold the key until you hear the

confirmation tone.

Ensure that the system is armed.Stay

Armed

Zones

87654321

Ready

Alarm

Service



If the system is fitted with a Premier RKP16 Plus the

Instant light will also illuminate.

Operating the Alarm System Premier 412 & 816 Master User Manual

8 INS141-5

➤ To change from Instant Stay to Delayed Stay, proceed

as follows:

Armed

Zones

87654321

Ready

Alarm

Service

DELAYED STAY

17: 8.21 28/04

The light will flash slowly.

The system is armed.

Armed

Delayed Stay

Press and hold the key until you hear the

confirmation tone.

Ensure that the system is armed.Instant Stay



If your system is fitted with a Premier RKP16 Plus the

Instant light will go off.

Arming and Disarming Partitions

This section covers arming and disarming partitions. In

order to use these procedures the following requirements

must be configured:

• The alarm system must be split into one or more

partitions.

• Your Access code must be assigned to more than one

partition.

• The keypad that you use to operate the alarm system

must be assigned to multiple partitions OR your Access

code is enabled for Global Access.

Away Arming Partitions

This option allows you to Away arm one or more partitions.

➤ To Away arm selected partitions, proceed as follows:

YES to Arm?

Area > **.. <

Armed

Zones

87654321

Ready

Alarm

Service

YES to Arm?

MENU for Options

The light will flash quickly.Ready

Press - to select/deselect partitions,

e.g. Press to select Partition 2.

Press A

Enter Access code ????

Armed

Zones

87654321

Ready

Alarm

Service

YES to Arm?

Area > *2.. <

Partition 2 is now selected.

Armed

Zones

87654321

Ready

Alarm

Service

Press aPress y

Please Exit....

17: 0.21 28/04

The light will flash and the exit tone will sound.

, when the partition has

armed the exit tone will stop. The selected partition(s) is

now Away armed.

Armed

Leave the area being armed

Armed

Zones

87654321

Ready

Alarm

Service



If the Quick Arm feature is enabled, you can omit step

1 from the above procedure.

Stay Arming Partitions

This option allows you to Stay arm one or more partitions.

➤ To Stay Arm selected partitions, proceed as follows:

YES to Arm?

Area > **.. <

YES to Arm?

MENU for Options

The light will flash quickly.Ready

Press - to select/deselect partitions,

e.g. Press to select Partition 1.

Press A

Enter Access code ????

Armed

Zones

87654321

Ready

Alarm

Service

YES to Arm?

Area > 1*.. <

Partition 1 is now selected.

Armed

Zones

87654321

Ready

Alarm

Service

4Press s

Premier 816

17: 0.21 28/04

Armed

Zones

87654321

Ready

Alarm

Service

The selected partition(s) will arm immediately and the

light will flash.

The selected partition(s) is now armed.

Armed

Stay

Armed

Zones

87654321

Ready

Alarm

Service

Disarming Partitions

This option allows you to disarm one or more partitions.

➤ To disarm selected partitions, proceed as follows:

NO to Disarm?

Area > **.. <

MENU for Options

NO to Disarm?

The light will flash quickly.Ready

Press - to select/deselect partitions,

e.g. Press to select Partition 2.

Press A

Enter Access code ????

Armed

Zones

87654321

Ready

Alarm

Service

NO to Disarm?

Area > *2.. <

Partition 2 is now selected for disarm.

Armed

Zones

87654321

Ready

Alarm

Service

Press d

Premier 816

17: 0.21 28/04

Armed

Zones

87654321

Ready

Alarm

Service

The selected partitions are disarmed.

Press n

Armed

Zones

87654321

Ready

Alarm

Service

Premier 412 & 816 Master User Manual Operating the Alarm System

INS141-5 9

Changing to another Partition

Normally the remote keypad that you use will be assigned to

a particular partition and therefore the zone and status lights

will indicate information relevant to the assigned partition.

However, you can temporarily switch the remote keypad to a

different partition so that the zone and status lights indicate

the information relevant to the partition that you have

selected. Whilst in this mode you can also use your Access

code to arm/disarm the partition you have selected

(providing you have access to the selected partition).

In order to use the cross partitioning feature, it is

recommend that the system is configured as follows:

• Cross partitioning must be enabled.

• The user must be assigned to multiple partitions.

• The user should be set for “Local Partition Access Only”,

see page 17.

• The remote keypads should only be assigned to a

single partition.

➤ To change to another partition, proceed as follows:

AREA ARMED >....

17: 5. 4 28/04

Enter partition - ,

e.g. Press to select Partition 2.

Press A

Armed

Zones

87654321

Ready

Alarm

Service

Premier 816

17: 5. 8 28/04

The remote keypad will now indicate information

relevant to the selected partition.

Armed

Zones

87654321

Ready

Alarm

Service



After changing to the selected partition, the remote

keypad will only remain in the selected partition for 10

seconds after the last key press. However if an

Access code is entered whilst the remote is in this

mode, the remote keypad will remain in the selected

partition for 1 minute after the last key press.

Bypassing Zones

Manually Bypassing Zones

Bypassing a zone prevents it from causing an alarm.



After manually bypassing a zone, the zone will remain

bypassed until the zone is manually unbypassed.

The Bypass menu will time-out if no key is pressed for

60 seconds.

➤ To manually bypass zones, proceed as follows:

Bypass Zone> 00

*NONE BYPASSED*

Armed

Zones

87654321

Ready

Alarm

Service

YES to Arm?

MENU for Options

The light will flash quickly.Ready

Enter the zone number ,

e.g. Enter to select Zone 2.

Press B

Enter Access code ????

Armed

Zones

87654321

Ready

Alarm

Service

Bypass Zone> 02

Zone 02 Bypassed

The selected zone is now bypassed. Repeat step 3 to

bypass additional zones.

Armed

Zones

87654321

Ready

Alarm

Service

Once the selected zones have been bypassed press:

/ to Away arm

to Stay arm

to return to the normal disarmed state



If the Quick Bypass feature is enabled, you can omit

step 1 from the above procedure.

When one or more zones are bypassed the Ready

light will flash and if the system is fitted with a Premier

RKP16 Plus or Premier LCD/LCDL then the Bypass

light will also illuminate.

Unbypassing Zones

To manually unbypass zones, perform the manual Bypass

procedure on a zone that is already bypassed.

• 24 hour zones cannot be unbypassed if they are still

violated.

• If your installer has enabled the “Reinstate Bypassed

Zones on Disarm” option, all zones will automatically be

unbypassed each time the system is disarmed.

Group Bypass

The Group Bypass feature allows you to bypass a

predefined group of zones. The alarm system has up to four

groups.

Operating the Alarm System Premier 412 & 816 Master User Manual

10 INS141-5

➤ To bypass a group of zones, proceed as follows:

Bypass Zone> 00

Zone 0 Bypassed

YES to Arm?

MENU for Options

The keypad will display the bypassed zones.

If required, zones can be added or removed from the

group by entering the required zone number ,

e.g. Enter to add Zone 5.

Enter bypass group 14- followed by B

Enter Access code ????

Armed

Zones

87654321

Ready

Alarm

Service

Bypass Zone> 05

Zone 0 Bypassed

The selected zone is now bypassed. Repeat step 3 to

bypass additional zones.

Armed

Zones

87654321

Ready

Alarm

Service

Once the selected zones have been bypassed press:

/ to Away arm

to Stay arm

to return to the normal disarmed state

Bypass Zone> 00

Zone 04 Bypassed

Bypass Zone> 05

Zone 04 Bypassed

Bypass Zone> 05

Zone 05 Bypassed

Armed

Zones

87654321

Ready

Alarm

Service



If the Quick Bypass feature is enabled, you can omit

step 1 from the above procedure.

When one or more zones are bypassed the Ready

light will flash and if the system is fitted with a Premier

RKP16 Plus or Premier LCD/LCDL then the Bypass

light will also illuminate.

Quick Bypass and Arm

The Quick Bypass and Arm feature allows you to bypass a

predefined group of zones and Away or Stay arm the

system. The alarm system has up to four groups.

➤ To Quick Bypass a group of zones and Away arm,

proceed as follows:

Armed

Zones

87654321

Ready

Alarm

Service

Premier 816

19: 0.56 28/04

Enter bypass group 14-

Armed

Zones

87654321

Ready

Alarm

Service

Press aPress y

Please Exit....

19: 0.56 28/04

The and lights will flash and the exit tone

will sound.

When the system is Away armed

with the selected group of zones bypassed.

Armed Ready

exit tone stops, the

➤ To Quick Bypass a group of zones and Stay arm,

proceed as follows:

Armed

Zones

87654321

Ready

Alarm

Service

Premier 816

19: 0.56 28/04

Enter bypass group 14-

Armed

Zones

87654321

Ready

Alarm

Service

Press s

Premier 816

19: 0.56 28/04

The alarm system will arm immediately and t

The

and lights will flash.

system is Stay armed with the selected group of

zones bypassed.

Armed

Ready



The Quick Arm feature must be enabled to use this

feature.

Andere Handbücher für Premier 412

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Texecom Bedienfeld Handbücher

Texecom

Texecom Veritas R8 Plus Bedienungsanleitung

Texecom

Texecom Premier 832 Bedienungsanleitung

Texecom

Texecom Veritas R8Plus Bedienungsanleitung

Texecom

Texecom Premier Elite Micro Contact-W Bedienungsanleitung

Texecom

Texecom Premier Elite 48-W Bedienungsanleitung

Texecom

Texecom Premier 412 Bedienungsanleitung

Texecom

Texecom Veritas Excel Master Bedienungsanleitung

Texecom

Texecom Premier 412 Bedienungsanleitung

Texecom

Texecom Premier 888 Bedienungsanleitung

Texecom

Texecom Premier Elite Series Bedienungsanleitung

Texecom

Texecom Premier 24 Gebrauchsanweisung

Texecom

Texecom PREMIER 48 Bedienungsanleitung

Texecom

Texecom Premier 24 Montage- und Bedienungsanleitung

Texecom

Texecom PREMIER 48 Bedienungsanleitung

Texecom

Texecom Premier 24 Bedienungsanleitung

Texecom

Texecom Premier 8SP Bedienungsanleitung

Texecom

Texecom Premier Elite 88 Bedienungsanleitung

Texecom

Texecom Veritas 8 Bedienungsanleitung

Texecom

Texecom Veritas R8 Plus Bedienungsanleitung

Texecom

Texecom Premier Elite ComIP Bedienungsanleitung

Texecom

Texecom Premier 24 Bedienungsanleitung

Texecom

Texecom Premier 412 Bedienungsanleitung

Texecom

Texecom Premier 24 Bedienungsanleitung

Texecom

Texecom Premier 412 Premier 816 Premier 832 Bedienungsanleitung

Beliebte Bedienfeld Handbücher anderer Marken

RDZ

RDZ PC-HRX Bedienungsanleitung

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Technisches Handbuch

Efka

Efka Variocontrol V810 Bedienungsanleitung

Cebora

Cebora 208-10 Bedienungsanleitung

AMX

AMX AutoPatch CP-15 Bedienungsanleitung

Satel

Satel CA-6 KLED-S Bedienungsanleitung

Evolution

Evolution IQ plus 800 Bedienungsanleitung

Fagor

Fagor 8040 TCO CNC Bedienungsanleitung

Trane

Trane ComfortLink II XL950 Control Bedienungsanleitung

AKO

AKO PROCool AKO-17635-2 Bedienungsanleitung

ABB

ABB 6136/30M-101 Bedienungsanleitung

Telikou

Telikou BK-603 Belt Pack Bedienungsanleitung

Mapei

Mapei Mapeheat Thermo Touch Bedienungsanleitung

Bosch

Bosch D9412GV4 Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Bedienungsanleitung

Sminn

Sminn BOX L VF1L EI Bedienungsanleitung

Balboa

Balboa TP600 Bedienungsanleitung

Nice

Nice HSCU1 Technische Daten