Timeguard SLB2300RF Handbuch
Installation & Operating Instructions
2300W PIR Light Controller
c/w RF Control
Model: SLB2300RF – Black
Model: SLW2300RF – White
Model: LEDPROFOB RF Remote Fob
1
1. General Information
These instructions should be read carefully
and retained for further reference and maintenance.
2. Safety
• Before installation or maintenance, ensure the
mains supply to the PIR sensor is switched off
and the circuit supply fuses are removed or the
circuit breaker turned off.
• It is recommended that a qualified electrician is
consulted or used for the installation of this PIR
sensor and install in accordance with the current
IEE wiring and Building Regulations.
• Check that the total load on the circuit including
when this PIR sensor is fitted does not exceed the
rating of the circuit cable, fuse or circuit breaker.
3. Technical Specifications
PIR Light Controller
• Operating Voltage: 230V AC 50 Hz
• This product is of Class ll Construction and must
not be earthed
•Detection Angle: 180°
• Motion Detection Range:
Up to 12m distance at a 2.5m mounting height
2
• Back plate Mounting Centres: 51mm
• Maximum Switching Load;
2300W Halogen lighting
500W Fluorescent tube w/o PF correction
250W LED lighting (PF > 0.9)
200W CFL Lighting
• Time ON Adjustment: 3 seconds to 18 minutes
• Warm Up Period: Approximately 35 seconds
• Dusk (LUX) level adjustment: 2 to 1000 Lux
• Operating Temperature: -20°C to +40°C
• Standby (W): <0.5W
• Manual Override Mode: ON/OFF operation using
RF Remote Fob (6 fobs max)
• Sensor Head Adjustment: Pan angle = Left/right
90°, Tilt angle = Up 15°, Down 60°
• RF Module: RX Receiver
• RF Frequency: 433.92MHz
• IP55 Rated suitable for restricted external
applications
• CE Compliant
• Dimensions (H x W x D): 96 x 78 x 158mm
•Multiple PIR light controller switching: A maximum
of 8 SLB-W2300RF PIR light controllers can be wired
in parallel, to enable any detector to turn ON all the
lights connected. The total load must not exceed
the lamp rating of a single SLB-W2300RF unit.
3
RF Remote Fob
• Battery: 3V (1x CR2032)
• Battery Life:
Approximately 24 months (@ 10x opt/day)
• Class Rating: Class III
• Transmission and Receiving Distance:
100m hand held (clear line of sight)
10m when mounted inside a wall switch
(recommended mounting height = 1.2m)
• Total number of fobs usable per PIR: 6
• Operating Temperature: -20°C to +40°C
•RF Module: TX Transmitter
• RF Frequency: 433.72MHz to 434.12MHz
• IP44 Rated suitable for restricted external
applications
• CE Compliant
• Dimensions (H x W x D): 60 x 38 x 15mm
4. Pack contents
• 1x SLB-W2300RF PIR Light Controller
• 1x LEDPROFOB RF Remote Fob
• 1x Instruction Manual
• 1x 3V CR2032 Battery
• 1x Lens Sticker
• 2x Fixing Screws
•2x Wall Plugs
• 2x Wire (for wall mounting a fob)
4
5. Selecting a Location
• The light controller has number of detection zones,
at various vertical and horizontal angles as shown
(see diagram A).
• A moving human body needs to cross/enter one
of these zones to activate the light controller.
The best all-round coverage is achieved with the
unit mounted at the optimum height of 2.5 metres.
• Careful positioning of the light controller will be
required to ensure optimum performance (see
diagram A detailing detection range and direction).
• The light controller is more sensitive to movement
ACROSS its field of vision than to movement
directly TOWARDS (see diagram B). Therefore
position the unit so that the light controller looks
ACROSS the likely approach path.
• Avoid positioning the light controller where
there are any sources of heat in the detection
area (extractor fans, tumble dryer exhausts etc.)
including opposite any other light sources such
as other security lights.
• Reflective surfaces (i.e. pools of water or white
painted walls) and overhanging branches may
cause false activation under extreme conditions.
5
6. Installation
6.1 Ensure the mains supply is
switched off and the circuit
supply fuses are removed or
the circuit breaker turned off.
6.2 An isolating switch should be installed
to enable the power to be switched ON & OFF
for maintenance purposes.
• During extreme weather conditions the motion
light controller may exhibit unusual behaviour.
This does not indicate a fault with the light
controller. Once normal weather conditions return,
the light controller will resume normal operation.
6
6.3 Remove the back plate from the PIR light controller.
6.4 Mark the position of the mounting holes on the
wall using the back box as a template.
6.5 Drill the holes ensuring not to infringe with any
gas/water pipes or electrical cables that may be
hidden below the surface. Insert the rawl plugs
into the holes.
6.6 Pass the 230V 50Hz mains supply and load
cables through the cable entry point on the
backing plate, ensuring the grommet(s) is used to
maintain the IP rating of the PIR light controller.
7
6.7 Fix the back plate to the wall. Take care not to
overtighten the screws to prevent damage to the
back plate. If using a power screwdriver, use the
lowest torque setting.
6.8 Terminate the cables into the terminal block
ensuring correct polarity is observed and that
all bare conductors are sleeved (See section 6.
Connection Diagram).
6.9 Re-attach the PIR light controller to the back
plate pushing firmly into place.
LN
230V AC 50Hz
MAINS SUPPLY LOAD
L
N
ISOLATION
SWITCH
LOOP
TERMINAL Ll
8
7. Connection Diagram
• Connect the cables to the terminal block as follows;
Load
Switch Live (Brown or Red) to L1
Neutral Load (Blue or Black) to N
230V 50Hz Mains Supply
Live Supply (Brown or Red) to L
Neutral Supply (Blue or Black) to N
A ‘Loop Terminal’ (centre terminal) is provided
should a 3 core cable be used
9
8. Setting Up
Walk Test Procedure (Test Mode)
• The sensor will rotate from left to right, and will
tilt downwards. Adjust the light controller to point
in the required direction and angle down to limit
forward range as required.
• Set the two adjustment controls on the underside
of the unit to the following positions:
DELAY TIME ADJUST – Fully anti-clockwise
DUSK LEVEL ADJUST – Fully clockwise
• Turn the power to the unit ON.
Andere Handbücher für SLB2300RF
1
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Timeguard Controller Handbücher
Timeguard
Timeguard TRT039N Handbuch
Timeguard
Timeguard E269H-Synchronous Handbuch
Timeguard
Timeguard SLFM360N Handbuch
Timeguard
Timeguard PDRS1500N Montageanleitung
Timeguard
Timeguard ProgramaSTAT UFPT24 Bedienungsanleitung
Timeguard
Timeguard SLDD1000 Handbuch
Timeguard
Timeguard SureTime STLW1000 Handbuch
Timeguard
Timeguard RTS113Q Programmierhandbuch
Timeguard
Timeguard SLW360L Handbuch
Timeguard
Timeguard MLB3000 Handbuch
Timeguard
Timeguard RTS113 Programmierhandbuch
Timeguard
Timeguard PDFM1500 Handbuch
Timeguard
Timeguard SLB2300 Handbuch
Timeguard
Timeguard LEDPRORFKB Handbuch
Timeguard
Timeguard PDWM1500 Handbuch
Timeguard
Timeguard PDFM1500N Handbuch
Timeguard
Timeguard ELU56 Handbuch
Timeguard
Timeguard MLSA360N Handbuch
Timeguard
Timeguard MTLW3000 Handbuch
Timeguard
Timeguard MLB3000 Handbuch
